Sven Eckelmann a4c0c031b8 ath79: Add support for OpenMesh OM5P-AC v2 ... Device specifications: ====================== * Qualcomm/Atheros QCA9558 ver 1 rev 0 * 720/600/200 MHz (CPU/DDR/AHB) * 128 MB of RAM * 16 MB of SPI NOR flash - 2x 7 MB available; but one of the 7 MB regions is the recovery image * 2T2R 2.4 GHz Wi-Fi (11n) * 2T2R 5 GHz Wi-Fi (11ac) * 4x GPIO-LEDs (3x wifi, 1x power) * 1x GPIO-button (reset) * external h/w watchdog (enabled by default)) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring * 2x ethernet - eth0 + AR8035 ethernet PHY (RGMII) + 10/100/1000 Mbps Ethernet + 802.3af POE + used as LAN interface - eth1 + AR8031 ethernet PHY (RGMII) + 10/100/1000 Mbps Ethernet + 18-24V passive POE (mode B) + used as WAN interface * 12-24V 1A DC * internal antennas This device support is based on the partially working stub from commit 53c474abbd ("ath79: add new OF only target for QCA MIPS silicon"). Flashing instructions: ====================== Various methods can be used to install the actual image on the flash. Two easy ones are: ap51-flash ---------- The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the image to the u-boot when the device boots up. initramfs from TFTP ------------------- The serial console must be used to access the u-boot shell during bootup. It can then be used to first boot up the initramfs image from a TFTP server (here with the IP 192.168.1.21): setenv serverip 192.168.1.21 setenv ipaddr 192.168.1.1 tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr The actual sysupgrade image can then be transferred (on the LAN port) to the device via scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/ On the device, the sysupgrade must then be started using sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin Signed-off-by: Sven Eckelmann <sven@narfation.org> (cherry picked from commit 1699c1dc7f)		2022-02-11 00:28:52 +01:00
..
bin	ath79: add support for PISEN WMB001N	2019-08-08 21:00:59 +08:00
lzma-loader	ath79: lzma-loader: allow setting custom kernel magic	2021-06-11 07:20:31 +02:00
common-buffalo.mk	ath79: use common device definition for Buffalo devices	2020-09-16 17:31:03 +02:00
common-mikrotik.mk	ath79/mikrotik: disable building NAND images	2020-12-27 20:33:57 +01:00
common-netgear.mk	ath79: fix factory image generation for Netgear and Zyxel boards	2021-02-14 19:21:38 +01:00
common-senao.mk	ath79: add Senao 'failsafe' sysupgrade procedure	2021-06-11 07:20:31 +02:00
common-tp-link.mk	ath79: replace custom uImageArcher generation	2020-06-29 01:08:09 +02:00
common-yuncore.mk	ath79: add support for YunCore TFTP image generation	2019-11-25 17:32:46 +01:00
generic-tp-link.mk	treewide: make AddDepends/usb-serial selective	2021-06-08 22:50:32 +02:00
generic-ubnt.mk	ath79: add support for Ubiquiti UniFi AP Outdoor+	2021-02-01 00:47:46 +01:00
generic.mk	ath79: Add support for OpenMesh OM5P-AC v2	2022-02-11 00:28:52 +01:00
Makefile	ath79: set lzma-loader variables to null by default	2021-06-11 07:20:31 +02:00
mikrotik.mk	ath79: add support for MikroTik RouterBOARD 912UAG-2HPnD	2021-07-09 17:14:01 +02:00
nand.mk	ath79: fix factory image generation for Netgear and Zyxel boards	2021-02-14 19:21:38 +01:00
tiny-netgear.mk	ath79: netgear: trim down uImage customisations	2020-11-25 16:33:49 +01:00
tiny-tp-link.mk	ath79: add support for TP-Link TL-WA901ND v3	2020-08-08 20:40:48 +02:00
tiny.mk	ath79: adjust ath79/tiny Senao APs to 4k blocksize	2021-06-11 07:20:31 +02:00