mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-26 08:51:13 +00:00
f9c28222c8
FCC ID: A8J-ESR900
Engenius ESR1200 is an indoor wireless router with
a gigabit ethernet switch, dual-band wireless,
internal antenna plates, and a USB 2.0 port
**Specification:**
- QCA9557 SOC 2.4 GHz, 2x2
- QCA9882 WLAN PCIe mini card, 5 GHz, 2x2
- QCA8337N SW 4 ports LAN, 1 port WAN
- 40 MHz clock
- 16 MB FLASH MX25L12845EMI-10G
- 2x 64 MB RAM
- UART at J1 populated, RX grounded
- 6 internal antenna plates (omni-directional)
- 5 LEDs, 1 button (power, 2G, 5G, WAN, WPS) (reset)
**MAC addresses:**
Base MAC address labeled as "MAC ADDRESS"
MAC "wanaddr" is not similar to "ethaddr"
eth0 *:c8 MAC u-boot-env ethaddr
phy0 *:c8 MAC u-boot-env ethaddr
phy1 *:c9 --- u-boot-env ethaddr +1
WAN *:66:44 u-boot-env wanaddr
**Serial Access:**
RX on the board for UART is shorted to ground by resistor R176
therefore it must be removed to use the console
but it is not necessary to remove to view boot log
optionally, R175 can be replaced with a solder bridge short
the resistors R175 and R176 are next to the UART RX pin
**Installation:**
Method 1: Firmware upgrade page
OEM webpage at 192.168.0.1
username and password "admin"
Navigate to Settings (gear icon) --> Tools --> Firmware
select the factory.bin image
confirm and wait 3 minutes
Method 2: TFTP recovery
Follow TFTP instructions using initramfs.bin
use sysupgrade.bin to flash using openwrt web interface
**Return to OEM:**
MTD partitions should be backed up before flashing
using TFTP to boot openwrt without overwriting flash
Alternatively, it is possible to edit OEM firmware images
to flash MTD partitions in openwrt to restore OEM firmware
by removing the OEM header and writing the rest to "firmware"
**TFTP recovery:**
Requires serial console, reset button does nothing at boot
rename initramfs.bin to 'uImageESR1200'
make available on TFTP server at 192.168.99.8
power board, interrupt boot by pressing '4' rapidly
execute tftpboot and bootm
**Note on ETH switch registers**
Registers must be written to the ethernet switch
in order to set up the switch's MAC interface.
U-boot can write the registers on it's own
which is needed, for example, in a TFTP transfer.
The register bits from OEM for the QCA8337 switch
can be read from interrupted boot (tftpboot, bootm)
by adding print lines in the switch driver ar8327.c
before 'qca,ar8327-initvals' is parsed from DTS and written.
for example:
pr_info("0x04 %08x\n", ar8xxx_read(priv, AR8327_REG_PAD0_MODE));
Signed-off-by: Michael Pratt <mcpratt@pm.me>
3024 lines
84 KiB
Makefile
3024 lines
84 KiB
Makefile
include ./common-buffalo.mk
|
|
include ./common-netgear.mk
|
|
include ./common-senao.mk
|
|
include ./common-tp-link.mk
|
|
include ./common-yuncore.mk
|
|
include ./common-ubnt.mk
|
|
|
|
DEVICE_VARS += ADDPATTERN_ID ADDPATTERN_VERSION
|
|
DEVICE_VARS += SEAMA_SIGNATURE SEAMA_MTDBLOCK
|
|
DEVICE_VARS += KERNEL_INITRAMFS_PREFIX DAP_SIGNATURE
|
|
DEVICE_VARS += EDIMAX_HEADER_MAGIC EDIMAX_HEADER_MODEL
|
|
DEVICE_VARS += OPENMESH_CE_TYPE ZYXEL_MODEL_STRING
|
|
DEVICE_VARS += SUPPORTED_TELTONIKA_DEVICES
|
|
|
|
define Build/addpattern
|
|
-$(STAGING_DIR_HOST)/bin/addpattern -B $(ADDPATTERN_ID) \
|
|
-v v$(ADDPATTERN_VERSION) -i $@ -o $@.new
|
|
-mv "$@.new" "$@"
|
|
endef
|
|
|
|
define Build/append-md5sum-bin
|
|
$(MKHASH) md5 $@ | sed 's/../\\\\x&/g' |\
|
|
xargs echo -ne >> $@
|
|
endef
|
|
|
|
define Build/cybertan-trx
|
|
@echo -n '' > $@-empty.bin
|
|
-$(STAGING_DIR_HOST)/bin/trx -o $@.new \
|
|
-f $(IMAGE_KERNEL) -F $@-empty.bin \
|
|
-x 32 -a 0x10000 -x -32 -f $@
|
|
-mv "$@.new" "$@"
|
|
-rm $@-empty.bin
|
|
endef
|
|
|
|
define Build/edimax-headers
|
|
$(eval edimax_magic=$(word 1,$(1)))
|
|
$(eval edimax_model=$(word 2,$(1)))
|
|
|
|
$(STAGING_DIR_HOST)/bin/edimax_fw_header -M $(edimax_magic) -m $(edimax_model)\
|
|
-v $(VERSION_DIST)$(firstword $(subst +, , $(firstword $(subst -, ,$(REVISION))))) \
|
|
-n "uImage" \
|
|
-i $(KDIR)/loader-$(DEVICE_NAME).uImage \
|
|
-o $@.uImage
|
|
$(STAGING_DIR_HOST)/bin/edimax_fw_header -M $(edimax_magic) -m $(edimax_model)\
|
|
-v $(VERSION_DIST)$(firstword $(subst +, , $(firstword $(subst -, ,$(REVISION))))) \
|
|
-n "rootfs" \
|
|
-i $@ \
|
|
-o $@.rootfs
|
|
cat $@.uImage $@.rootfs > $@
|
|
rm -rf $@.uImage $@.rootfs
|
|
endef
|
|
|
|
define Build/mkdapimg2
|
|
$(STAGING_DIR_HOST)/bin/mkdapimg2 \
|
|
-i $@ -o $@.new \
|
|
-s $(DAP_SIGNATURE) \
|
|
-v $(VERSION_DIST)-$(firstword $(subst +, , \
|
|
$(firstword $(subst -, ,$(REVISION))))) \
|
|
-r Default \
|
|
$(if $(1),-k $(1))
|
|
mv $@.new $@
|
|
endef
|
|
|
|
define Build/mkmylofw_16m
|
|
$(eval device_id=$(word 1,$(1)))
|
|
$(eval revision=$(word 2,$(1)))
|
|
|
|
# On WPJ344, WPJ531, and WPJ563, the default boot command tries 0x9f680000
|
|
# first and fails if the remains of the stock image are sill there
|
|
# - resulting in an infinite boot loop.
|
|
# The size parameter is grown to have that block deleted if the firmware
|
|
# isn't big enough by itself.
|
|
|
|
let \
|
|
size="$$(stat -c%s $@)" \
|
|
pad="$(subst k,* 1024,$(BLOCKSIZE))" \
|
|
pad="(pad - (size % pad)) % pad" \
|
|
newsize='size + pad' ; \
|
|
[ $$newsize -lt $$((0x660000)) ] && newsize=0x660000 ; \
|
|
$(STAGING_DIR_HOST)/bin/mkmylofw \
|
|
-B WPE72 -i 0x11f6:$(device_id):0x11f6:$(device_id) -r $(revision) \
|
|
-s 0x1000000 -p0x30000:$$newsize:al:0x80060000:"OpenWRT":$@ \
|
|
$@.new
|
|
@mv $@.new $@
|
|
endef
|
|
|
|
define Build/mkwrggimg
|
|
$(STAGING_DIR_HOST)/bin/mkwrggimg -b \
|
|
-i $@ -o $@.imghdr -d /dev/mtdblock/1 \
|
|
-m $(DEVICE_MODEL)-$(DEVICE_VARIANT) -s $(DAP_SIGNATURE) \
|
|
-v $(VERSION_DIST) -B $(REVISION)
|
|
mv $@.imghdr $@
|
|
endef
|
|
|
|
define Build/nec-enc
|
|
$(STAGING_DIR_HOST)/bin/nec-enc \
|
|
-i $@ -o $@.new -k $(1)
|
|
mv $@.new $@
|
|
endef
|
|
|
|
define Build/nec-fw
|
|
( stat -c%s $@ | tr -d "\n" | dd bs=16 count=1 conv=sync; ) >> $@
|
|
( \
|
|
echo -n -e "$(1)" | dd bs=16 count=1 conv=sync; \
|
|
echo -n "0.0.00" | dd bs=16 count=1 conv=sync; \
|
|
dd if=$@; \
|
|
) > $@.new
|
|
mv $@.new $@
|
|
endef
|
|
|
|
define Build/pisen_wmb001n-factory
|
|
-[ -f "$@" ] && \
|
|
mkdir -p "$@.tmp" && \
|
|
cp "$(KDIR)/loader-$(word 1,$(1)).uImage" "$@.tmp/uImage" && \
|
|
mv "$@" "$@.tmp/rootfs" && \
|
|
cp "bin/pisen_wmb001n_factory-header.bin" "$@" && \
|
|
$(TAR) -cp --numeric-owner --owner=0 --group=0 --mode=a-s --sort=name \
|
|
$(if $(SOURCE_DATE_EPOCH),--mtime="@$(SOURCE_DATE_EPOCH)") \
|
|
-C "$@.tmp" . | gzip -9n >> "$@" && \
|
|
rm -rf "$@.tmp"
|
|
endef
|
|
|
|
define Build/teltonika-fw-fake-checksum
|
|
# Teltonika U-Boot web based firmware upgrade/recovery routine compares
|
|
# 16 bytes from md5sum1[16] field in TP-Link v1 header (offset: 76 bytes
|
|
# from begin of the firmware file) with 16 bytes stored just before
|
|
# 0xdeadc0de marker. Values are only compared, MD5 sum is not verified.
|
|
let \
|
|
offs="$$(stat -c%s $@) - $(1)"; \
|
|
dd if=$@ bs=1 count=16 skip=76 |\
|
|
dd of=$@ bs=1 count=16 seek=$$offs conv=notrunc
|
|
endef
|
|
|
|
define Build/teltonika-v1-header
|
|
$(STAGING_DIR_HOST)/bin/mktplinkfw \
|
|
-c -H $(TPLINK_HWID) -W $(TPLINK_HWREV) -L $(KERNEL_LOADADDR) \
|
|
-E $(if $(KERNEL_ENTRY),$(KERNEL_ENTRY),$(KERNEL_LOADADDR)) \
|
|
-m $(TPLINK_HEADER_VERSION) -N "$(VERSION_DIST)" -V "RUT2xx " \
|
|
-k $@ -o $@.new $(1)
|
|
@mv $@.new $@
|
|
endef
|
|
|
|
metadata_json_teltonika = \
|
|
'{ $(if $(IMAGE_METADATA),$(IMAGE_METADATA)$(comma)) \
|
|
"metadata_version": "1.1", \
|
|
"compat_version": "$(call json_quote,$(compat_version))", \
|
|
"version":"$(call json_quote,$(VERSION_DIST))-$(call json_quote,$(VERSION_NUMBER))-$(call json_quote,$(REVISION))", \
|
|
"device_code": [".*"], \
|
|
"hwver": [".*"], \
|
|
"batch": [".*"], \
|
|
"serial": [".*"], \
|
|
$(if $(DEVICE_COMPAT_MESSAGE),"compat_message": "$(call json_quote,$(DEVICE_COMPAT_MESSAGE))"$(comma)) \
|
|
$(if $(filter-out 1.0,$(compat_version)),"new_supported_devices": \
|
|
[$(call metadata_devices,$(SUPPORTED_TELTONIKA_DEVICES))]$(comma) \
|
|
"supported_devices": ["$(call json_quote,$(legacy_supported_message))"]$(comma)) \
|
|
$(if $(filter 1.0,$(compat_version)),"supported_devices":[$(call metadata_devices,$(SUPPORTED_TELTONIKA_DEVICES))]$(comma)) \
|
|
"version_wrt": { \
|
|
"dist": "$(call json_quote,$(VERSION_DIST))", \
|
|
"version": "$(call json_quote,$(VERSION_NUMBER))", \
|
|
"revision": "$(call json_quote,$(REVISION))", \
|
|
"target": "$(call json_quote,$(TARGETID))", \
|
|
"board": "$(call json_quote,$(if $(BOARD_NAME),$(BOARD_NAME),$(DEVICE_NAME)))" \
|
|
}, \
|
|
"hw_support": {}, \
|
|
"hw_mods": {} \
|
|
}'
|
|
|
|
define Build/append-metadata-teltonika
|
|
echo $(call metadata_json_teltonika) | fwtool -I - $@
|
|
endef
|
|
|
|
define Build/wrgg-pad-rootfs
|
|
$(STAGING_DIR_HOST)/bin/padjffs2 $(IMAGE_ROOTFS) -c 64 >>$@
|
|
endef
|
|
|
|
define Build/zyxel-tar-bz2
|
|
mkdir -p $@.tmp
|
|
mv $@ $@.tmp/$(word 2,$(1))
|
|
cp $(KDIR)/loader-$(DEVICE_NAME).uImage $@.tmp/$(word 1,$(1)).lzma.uImage
|
|
$(TAR) -cjf $@ -C $@.tmp .
|
|
rm -rf $@.tmp
|
|
endef
|
|
|
|
define Device/seama
|
|
KERNEL := kernel-bin | append-dtb | relocate-kernel | lzma
|
|
KERNEL_INITRAMFS := $$(KERNEL) | seama
|
|
IMAGES += factory.bin
|
|
SEAMA_MTDBLOCK := 1
|
|
|
|
# 64 bytes offset:
|
|
# - 28 bytes seama_header
|
|
# - 36 bytes of META data (4-bytes aligned)
|
|
IMAGE/default := append-kernel | pad-offset $$$$(BLOCKSIZE) 64 | append-rootfs
|
|
IMAGE/sysupgrade.bin := $$(IMAGE/default) | seama | pad-rootfs | \
|
|
check-size | append-metadata
|
|
IMAGE/factory.bin := $$(IMAGE/default) | pad-rootfs -x 64 | seama | \
|
|
seama-seal | check-size
|
|
SEAMA_SIGNATURE :=
|
|
endef
|
|
|
|
|
|
define Device/8dev_carambola2
|
|
SOC := ar9331
|
|
DEVICE_VENDOR := 8devices
|
|
DEVICE_MODEL := Carambola2
|
|
DEVICE_PACKAGES := kmod-usb-chipidea2
|
|
IMAGE_SIZE := 16000k
|
|
SUPPORTED_DEVICES += carambola2
|
|
endef
|
|
TARGET_DEVICES += 8dev_carambola2
|
|
|
|
define Device/8dev_lima
|
|
SOC := qca9531
|
|
DEVICE_VENDOR := 8devices
|
|
DEVICE_MODEL := Lima
|
|
DEVICE_PACKAGES := kmod-usb2
|
|
IMAGE_SIZE := 15616k
|
|
SUPPORTED_DEVICES += lima
|
|
endef
|
|
TARGET_DEVICES += 8dev_lima
|
|
|
|
define Device/adtran_bsap1880
|
|
SOC := ar7161
|
|
DEVICE_VENDOR := Adtran/Bluesocket
|
|
DEVICE_PACKAGES += -swconfig -uboot-envtools fconfig
|
|
KERNEL := kernel-bin | append-dtb | lzma | pad-to $$(BLOCKSIZE)
|
|
KERNEL_INITRAMFS := kernel-bin | append-dtb
|
|
IMAGE_SIZE := 11200k
|
|
IMAGES += kernel.bin rootfs.bin
|
|
IMAGE/kernel.bin := append-kernel
|
|
IMAGE/rootfs.bin := append-rootfs | pad-rootfs | pad-to $$(BLOCKSIZE)
|
|
IMAGE/sysupgrade.bin := append-rootfs | pad-rootfs | \
|
|
check-size | sysupgrade-tar rootfs=$$$$@ | append-metadata
|
|
endef
|
|
|
|
define Device/adtran_bsap1800-v2
|
|
$(Device/adtran_bsap1880)
|
|
DEVICE_MODEL := BSAP-1800
|
|
DEVICE_VARIANT := v2
|
|
endef
|
|
TARGET_DEVICES += adtran_bsap1800-v2
|
|
|
|
define Device/adtran_bsap1840
|
|
$(Device/adtran_bsap1880)
|
|
DEVICE_MODEL := BSAP-1840
|
|
endef
|
|
TARGET_DEVICES += adtran_bsap1840
|
|
|
|
define Device/airtight_c-75
|
|
SOC := qca9550
|
|
DEVICE_VENDOR := AirTight Networks
|
|
DEVICE_MODEL := C-75
|
|
DEVICE_ALT0_VENDOR := Mojo Networks
|
|
DEVICE_ALT0_MODEL := C-75
|
|
DEVICE_ALT1_VENDOR := WatchGuard
|
|
DEVICE_ALT1_MODEL := AP320
|
|
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct kmod-usb2
|
|
IMAGE_SIZE := 32320k
|
|
KERNEL_SIZE := 15936k
|
|
endef
|
|
TARGET_DEVICES += airtight_c-75
|
|
|
|
define Device/alfa-network_ap121f
|
|
SOC := ar9331
|
|
DEVICE_VENDOR := ALFA Network
|
|
DEVICE_MODEL := AP121F
|
|
DEVICE_PACKAGES := kmod-usb-chipidea2 kmod-usb-storage -swconfig
|
|
IMAGE_SIZE := 16064k
|
|
SUPPORTED_DEVICES += ap121f
|
|
endef
|
|
TARGET_DEVICES += alfa-network_ap121f
|
|
|
|
define Device/alfa-network_ap121fe
|
|
SOC := ar9331
|
|
DEVICE_VENDOR := ALFA Network
|
|
DEVICE_MODEL := AP121FE
|
|
DEVICE_PACKAGES := kmod-usb-chipidea2 kmod-usb-gadget-eth -swconfig
|
|
IMAGE_SIZE := 16064k
|
|
endef
|
|
TARGET_DEVICES += alfa-network_ap121fe
|
|
|
|
define Device/alfa-network_n2q
|
|
SOC := qca9531
|
|
DEVICE_VENDOR := ALFA Network
|
|
DEVICE_MODEL := N2Q
|
|
DEVICE_PACKAGES := kmod-i2c-gpio kmod-gpio-pcf857x kmod-usb2 \
|
|
kmod-usb-ledtrig-usbport rssileds
|
|
IMAGE_SIZE := 15872k
|
|
endef
|
|
TARGET_DEVICES += alfa-network_n2q
|
|
|
|
define Device/alfa-network_n5q
|
|
SOC := ar9344
|
|
DEVICE_VENDOR := ALFA Network
|
|
DEVICE_MODEL := N5Q
|
|
DEVICE_PACKAGES := rssileds
|
|
IMAGE_SIZE := 15872k
|
|
SUPPORTED_DEVICES += n5q
|
|
endef
|
|
TARGET_DEVICES += alfa-network_n5q
|
|
|
|
define Device/alfa-network_pi-wifi4
|
|
SOC := qca9531
|
|
DEVICE_VENDOR := ALFA Network
|
|
DEVICE_MODEL := Pi-WiFi4
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport -swconfig
|
|
IMAGE_SIZE := 15872k
|
|
endef
|
|
TARGET_DEVICES += alfa-network_pi-wifi4
|
|
|
|
define Device/alfa-network_r36a
|
|
SOC := qca9531
|
|
DEVICE_VENDOR := ALFA Network
|
|
DEVICE_MODEL := R36A
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport
|
|
IMAGE_SIZE := 15872k
|
|
SUPPORTED_DEVICES += r36a
|
|
endef
|
|
TARGET_DEVICES += alfa-network_r36a
|
|
|
|
define Device/alfa-network_tube-2hq
|
|
SOC := qca9531
|
|
DEVICE_VENDOR := ALFA Network
|
|
DEVICE_MODEL := Tube-2HQ
|
|
DEVICE_PACKAGES := rssileds -swconfig
|
|
IMAGE_SIZE := 15872k
|
|
SUPPORTED_DEVICES += tube-2hq
|
|
endef
|
|
TARGET_DEVICES += alfa-network_tube-2hq
|
|
|
|
define Device/allnet_all-wap02860ac
|
|
$(Device/senao_loader_okli)
|
|
SOC := qca9558
|
|
DEVICE_VENDOR := ALLNET
|
|
DEVICE_MODEL := ALL-WAP02860AC
|
|
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct
|
|
IMAGE_SIZE := 11584k
|
|
LOADER_FLASH_OFFS := 0x220000
|
|
SENAO_IMGNAME := senao-allwap02860ac
|
|
endef
|
|
TARGET_DEVICES += allnet_all-wap02860ac
|
|
|
|
define Device/araknis_an-300-ap-i-n
|
|
$(Device/senao_loader_okli)
|
|
SOC := ar9344
|
|
DEVICE_VENDOR := Araknis
|
|
DEVICE_MODEL := AN-300-AP-I-N
|
|
IMAGE_SIZE := 12096k
|
|
LOADER_FLASH_OFFS := 0x220000
|
|
SENAO_IMGNAME := senao-an300
|
|
endef
|
|
TARGET_DEVICES += araknis_an-300-ap-i-n
|
|
|
|
define Device/araknis_an-500-ap-i-ac
|
|
$(Device/senao_loader_okli)
|
|
SOC := qca9557
|
|
DEVICE_VENDOR := Araknis
|
|
DEVICE_MODEL := AN-500-AP-I-AC
|
|
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct
|
|
IMAGE_SIZE := 11584k
|
|
LOADER_FLASH_OFFS := 0x220000
|
|
SENAO_IMGNAME := senao-generic-v1-an500
|
|
endef
|
|
TARGET_DEVICES += araknis_an-500-ap-i-ac
|
|
|
|
define Device/araknis_an-700-ap-i-ac
|
|
$(Device/senao_loader_okli)
|
|
SOC := qca9558
|
|
DEVICE_VENDOR := Araknis
|
|
DEVICE_MODEL := AN-700-AP-I-AC
|
|
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct
|
|
IMAGE_SIZE := 11584k
|
|
LOADER_FLASH_OFFS := 0x220000
|
|
SENAO_IMGNAME := senao-generic-v1-an700
|
|
endef
|
|
TARGET_DEVICES += araknis_an-700-ap-i-ac
|
|
|
|
define Device/arduino_yun
|
|
SOC := ar9331
|
|
DEVICE_VENDOR := Arduino
|
|
DEVICE_MODEL := Yun
|
|
DEVICE_PACKAGES := kmod-usb-chipidea2 kmod-usb-ledtrig-usbport \
|
|
kmod-usb-storage block-mount -swconfig
|
|
IMAGE_SIZE := 15936k
|
|
SUPPORTED_DEVICES += arduino-yun
|
|
endef
|
|
TARGET_DEVICES += arduino_yun
|
|
|
|
define Device/aruba_ap-105
|
|
SOC := ar7161
|
|
DEVICE_VENDOR := Aruba
|
|
DEVICE_MODEL := AP-105
|
|
IMAGE_SIZE := 16000k
|
|
DEVICE_PACKAGES := kmod-i2c-gpio kmod-tpm-i2c-atmel
|
|
endef
|
|
TARGET_DEVICES += aruba_ap-105
|
|
|
|
define Device/asus_pl-ac56
|
|
SOC := qca9563
|
|
DEVICE_VENDOR := ASUS
|
|
DEVICE_MODEL := PL-AC56
|
|
DEVICE_VARIANT := A1
|
|
IMAGE_SIZE := 15488k
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
|
append-rootfs | pad-rootfs
|
|
DEVICE_PACKAGES := kmod-ath10k-ct-smallbuffers ath10k-firmware-qca988x-ct
|
|
endef
|
|
TARGET_DEVICES += asus_pl-ac56
|
|
|
|
define Device/asus_rp-ac51
|
|
SOC := qca9531
|
|
DEVICE_VENDOR := ASUS
|
|
DEVICE_MODEL := RP-AC51
|
|
IMAGE_SIZE := 16000k
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
|
append-rootfs | pad-rootfs
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct \
|
|
-swconfig
|
|
endef
|
|
TARGET_DEVICES += asus_rp-ac51
|
|
|
|
define Device/asus_rp-ac66
|
|
SOC := qca9563
|
|
DEVICE_VENDOR := ASUS
|
|
DEVICE_MODEL := RP-AC66
|
|
IMAGE_SIZE := 16000k
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
|
append-rootfs | pad-rootfs
|
|
DEVICE_PACKAGES := kmod-ath10k-ct-smallbuffers ath10k-firmware-qca988x-ct \
|
|
rssileds -swconfig
|
|
endef
|
|
TARGET_DEVICES += asus_rp-ac66
|
|
|
|
define Device/atheros_db120
|
|
$(Device/loader-okli-uimage)
|
|
SOC := ar9344
|
|
DEVICE_VENDOR := Atheros
|
|
DEVICE_MODEL := DB120
|
|
DEVICE_PACKAGES := kmod-usb2
|
|
IMAGE_SIZE := 7808k
|
|
SUPPORTED_DEVICES += db120
|
|
LOADER_FLASH_OFFS := 0x50000
|
|
KERNEL := kernel-bin | append-dtb | lzma | uImage lzma -M 0x4f4b4c49
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
|
append-rootfs | pad-rootfs | check-size | pad-to 6336k | \
|
|
append-loader-okli-uimage $(1) | pad-to 64k
|
|
endef
|
|
TARGET_DEVICES += atheros_db120
|
|
|
|
define Device/avm
|
|
DEVICE_VENDOR := AVM
|
|
KERNEL := kernel-bin | append-dtb | lzma | eva-image
|
|
KERNEL_INITRAMFS := $$(KERNEL)
|
|
IMAGE/sysupgrade.bin := append-kernel | pad-to 64k | \
|
|
append-squashfs-fakeroot-be | pad-to 256 | append-rootfs | pad-rootfs | \
|
|
check-size | append-metadata
|
|
DEVICE_PACKAGES := fritz-tffs
|
|
endef
|
|
|
|
define Device/avm_fritz1750e
|
|
$(Device/avm)
|
|
SOC := qca9556
|
|
IMAGE_SIZE := 15232k
|
|
DEVICE_MODEL := FRITZ!WLAN Repeater 1750E
|
|
DEVICE_PACKAGES += rssileds kmod-ath10k-ct-smallbuffers \
|
|
ath10k-firmware-qca988x-ct -swconfig
|
|
endef
|
|
TARGET_DEVICES += avm_fritz1750e
|
|
|
|
define Device/avm_fritz300e
|
|
$(Device/avm)
|
|
SOC := ar7242
|
|
IMAGE_SIZE := 15232k
|
|
DEVICE_MODEL := FRITZ!WLAN Repeater 300E
|
|
DEVICE_PACKAGES += rssileds -swconfig
|
|
SUPPORTED_DEVICES += fritz300e
|
|
endef
|
|
TARGET_DEVICES += avm_fritz300e
|
|
|
|
define Device/avm_fritz4020
|
|
$(Device/avm)
|
|
SOC := qca9561
|
|
IMAGE_SIZE := 15232k
|
|
DEVICE_MODEL := FRITZ!Box 4020
|
|
SUPPORTED_DEVICES += fritz4020
|
|
endef
|
|
TARGET_DEVICES += avm_fritz4020
|
|
|
|
define Device/avm_fritz450e
|
|
$(Device/avm)
|
|
SOC := qca9556
|
|
IMAGE_SIZE := 15232k
|
|
DEVICE_MODEL := FRITZ!WLAN Repeater 450E
|
|
SUPPORTED_DEVICES += fritz450e
|
|
endef
|
|
TARGET_DEVICES += avm_fritz450e
|
|
|
|
define Device/avm_fritzdvbc
|
|
$(Device/avm)
|
|
SOC := qca9556
|
|
IMAGE_SIZE := 15232k
|
|
DEVICE_MODEL := FRITZ!WLAN Repeater DVB-C
|
|
DEVICE_PACKAGES += rssileds kmod-ath10k-ct-smallbuffers \
|
|
ath10k-firmware-qca988x-ct -swconfig
|
|
endef
|
|
TARGET_DEVICES += avm_fritzdvbc
|
|
|
|
define Device/belkin_f9x-v2
|
|
$(Device/loader-okli-uimage)
|
|
SOC := qca9558
|
|
DEVICE_VENDOR := Belkin
|
|
IMAGE_SIZE := 14464k
|
|
DEVICE_PACKAGES += kmod-ath10k-ct ath10k-firmware-qca988x-ct kmod-usb2 \
|
|
kmod-usb3 kmod-usb-ledtrig-usbport
|
|
LOADER_FLASH_OFFS := 0x50000
|
|
KERNEL := kernel-bin | append-dtb | lzma | uImage lzma -M 0x4f4b4c49
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
|
append-rootfs | pad-rootfs | check-size | \
|
|
edimax-headers $$$$(EDIMAX_HEADER_MAGIC) $$$$(EDIMAX_HEADER_MODEL) | \
|
|
pad-to $$$$(BLOCKSIZE)
|
|
endef
|
|
|
|
define Device/belkin_f9j1108-v2
|
|
$(Device/belkin_f9x-v2)
|
|
DEVICE_MODEL := F9J1108 v2 (AC1750 DB Wi-Fi)
|
|
EDIMAX_HEADER_MAGIC := F9J1108v1
|
|
EDIMAX_HEADER_MODEL := BR-6679BAC
|
|
endef
|
|
TARGET_DEVICES += belkin_f9j1108-v2
|
|
|
|
define Device/belkin_f9k1115-v2
|
|
$(Device/belkin_f9x-v2)
|
|
DEVICE_MODEL := F9K1115 v2 (AC1750 DB Wi-Fi)
|
|
EDIMAX_HEADER_MAGIC := eDiMaX
|
|
EDIMAX_HEADER_MODEL := F9K1115V2
|
|
endef
|
|
TARGET_DEVICES += belkin_f9k1115-v2
|
|
|
|
define Device/buffalo_bhr-4grv
|
|
$(Device/buffalo_common)
|
|
SOC := ar7242
|
|
DEVICE_MODEL := BHR-4GRV
|
|
BUFFALO_PRODUCT := BHR-4GRV
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport
|
|
IMAGE_SIZE := 32256k
|
|
SUPPORTED_DEVICES += wzr-hp-g450h
|
|
endef
|
|
TARGET_DEVICES += buffalo_bhr-4grv
|
|
|
|
define Device/buffalo_bhr-4grv2
|
|
SOC := qca9557
|
|
DEVICE_VENDOR := Buffalo
|
|
DEVICE_MODEL := BHR-4GRV2
|
|
IMAGE_SIZE := 16000k
|
|
endef
|
|
TARGET_DEVICES += buffalo_bhr-4grv2
|
|
|
|
define Device/buffalo_wzr_ar7161
|
|
$(Device/buffalo_common)
|
|
SOC := ar7161
|
|
BUFFALO_PRODUCT := WZR-HP-AG300H
|
|
DEVICE_PACKAGES := kmod-usb-ohci kmod-usb2 kmod-usb-ledtrig-usbport \
|
|
kmod-leds-reset kmod-owl-loader
|
|
IMAGE_SIZE := 32320k
|
|
SUPPORTED_DEVICES += wzr-hp-ag300h
|
|
endef
|
|
|
|
define Device/buffalo_wzr-600dhp
|
|
$(Device/buffalo_wzr_ar7161)
|
|
DEVICE_MODEL := WZR-600DHP
|
|
endef
|
|
TARGET_DEVICES += buffalo_wzr-600dhp
|
|
|
|
define Device/buffalo_wzr-hp-ag300h
|
|
$(Device/buffalo_wzr_ar7161)
|
|
DEVICE_MODEL := WZR-HP-AG300H
|
|
endef
|
|
TARGET_DEVICES += buffalo_wzr-hp-ag300h
|
|
|
|
define Device/buffalo_wzr-hp-g300nh
|
|
$(Device/buffalo_common)
|
|
SOC := ar9132
|
|
BUFFALO_PRODUCT := WZR-HP-G300NH
|
|
BUFFALO_HWVER := 1
|
|
DEVICE_PACKAGES := kmod-gpio-cascade kmod-mux-gpio kmod-usb2 kmod-usb-ledtrig-usbport
|
|
BLOCKSIZE := 128k
|
|
IMAGE_SIZE := 32128k
|
|
SUPPORTED_DEVICES += wzr-hp-g300nh
|
|
endef
|
|
|
|
define Device/buffalo_wzr-hp-g300nh-rb
|
|
$(Device/buffalo_wzr-hp-g300nh)
|
|
DEVICE_MODEL := WZR-HP-G300NH (RTL8366RB switch)
|
|
endef
|
|
TARGET_DEVICES += buffalo_wzr-hp-g300nh-rb
|
|
|
|
define Device/buffalo_wzr-hp-g300nh-s
|
|
$(Device/buffalo_wzr-hp-g300nh)
|
|
DEVICE_MODEL := WZR-HP-G300NH (RTL8366S switch)
|
|
DEVICE_PACKAGES += kmod-switch-rtl8366rb
|
|
endef
|
|
TARGET_DEVICES += buffalo_wzr-hp-g300nh-s
|
|
|
|
define Device/buffalo_wzr-hp-g302h-a1a0
|
|
$(Device/buffalo_common)
|
|
SOC := ar7242
|
|
DEVICE_MODEL := WZR-HP-G302H
|
|
DEVICE_VARIANT := A1A0
|
|
BUFFALO_PRODUCT := WZR-HP-G302H
|
|
BUFFALO_HWVER := 4
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport
|
|
IMAGE_SIZE := 32128k
|
|
SUPPORTED_DEVICES += wzr-hp-g300nh2
|
|
endef
|
|
TARGET_DEVICES += buffalo_wzr-hp-g302h-a1a0
|
|
|
|
define Device/buffalo_wzr-hp-g450h
|
|
$(Device/buffalo_common)
|
|
SOC := ar7242
|
|
DEVICE_MODEL := WZR-HP-G450H/WZR-450HP
|
|
BUFFALO_PRODUCT := WZR-HP-G450H
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport
|
|
IMAGE_SIZE := 32256k
|
|
SUPPORTED_DEVICES += wzr-hp-g450h
|
|
endef
|
|
TARGET_DEVICES += buffalo_wzr-hp-g450h
|
|
|
|
define Device/comfast_cf-e110n-v2
|
|
SOC := qca9533
|
|
DEVICE_VENDOR := COMFAST
|
|
DEVICE_MODEL := CF-E110N
|
|
DEVICE_VARIANT := v2
|
|
DEVICE_PACKAGES := rssileds -swconfig -uboot-envtools
|
|
IMAGE_SIZE := 16192k
|
|
endef
|
|
TARGET_DEVICES += comfast_cf-e110n-v2
|
|
|
|
define Device/comfast_cf-e120a-v3
|
|
SOC := ar9344
|
|
DEVICE_VENDOR := COMFAST
|
|
DEVICE_MODEL := CF-E120A
|
|
DEVICE_VARIANT := v3
|
|
DEVICE_PACKAGES := rssileds -uboot-envtools
|
|
IMAGE_SIZE := 8000k
|
|
endef
|
|
TARGET_DEVICES += comfast_cf-e120a-v3
|
|
|
|
define Device/comfast_cf-e130n-v2
|
|
SOC := qca9531
|
|
DEVICE_VENDOR := COMFAST
|
|
DEVICE_MODEL := CF-E130N
|
|
DEVICE_VARIANT := v2
|
|
DEVICE_PACKAGES := rssileds -swconfig -uboot-envtools
|
|
IMAGE_SIZE := 7936k
|
|
endef
|
|
TARGET_DEVICES += comfast_cf-e130n-v2
|
|
|
|
define Device/comfast_cf-e313ac
|
|
SOC := qca9531
|
|
DEVICE_VENDOR := COMFAST
|
|
DEVICE_MODEL := CF-E313AC
|
|
DEVICE_PACKAGES := rssileds kmod-ath10k-ct-smallbuffers \
|
|
ath10k-firmware-qca9888-ct -swconfig -uboot-envtools
|
|
IMAGE_SIZE := 7936k
|
|
endef
|
|
TARGET_DEVICES += comfast_cf-e313ac
|
|
|
|
define Device/comfast_cf-e314n-v2
|
|
SOC := qca9531
|
|
DEVICE_VENDOR := COMFAST
|
|
DEVICE_MODEL := CF-E314N
|
|
DEVICE_VARIANT := v2
|
|
DEVICE_PACKAGES := rssileds
|
|
IMAGE_SIZE := 7936k
|
|
endef
|
|
TARGET_DEVICES += comfast_cf-e314n-v2
|
|
|
|
define Device/comfast_cf-e375ac
|
|
SOC := qca9563
|
|
DEVICE_VENDOR := COMFAST
|
|
DEVICE_MODEL := CF-E375AC
|
|
DEVICE_PACKAGES := kmod-ath10k-ct \
|
|
ath10k-firmware-qca9888-ct -uboot-envtools
|
|
IMAGE_SIZE := 16000k
|
|
endef
|
|
TARGET_DEVICES += comfast_cf-e375ac
|
|
|
|
define Device/comfast_cf-e5
|
|
SOC := qca9531
|
|
DEVICE_VENDOR := COMFAST
|
|
DEVICE_MODEL := CF-E5/E7
|
|
DEVICE_PACKAGES := rssileds kmod-usb2 kmod-usb-net-qmi-wwan -swconfig \
|
|
-uboot-envtools
|
|
IMAGE_SIZE := 16192k
|
|
endef
|
|
TARGET_DEVICES += comfast_cf-e5
|
|
|
|
define Device/comfast_cf-e560ac
|
|
SOC := qca9531
|
|
DEVICE_VENDOR := COMFAST
|
|
DEVICE_MODEL := CF-E560AC
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca9888-ct
|
|
IMAGE_SIZE := 16128k
|
|
endef
|
|
TARGET_DEVICES += comfast_cf-e560ac
|
|
|
|
define Device/comfast_cf-ew72
|
|
SOC := qca9531
|
|
DEVICE_VENDOR := COMFAST
|
|
DEVICE_MODEL := CF-EW72
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca9888-ct \
|
|
-uboot-envtools -swconfig
|
|
IMAGE_SIZE := 16192k
|
|
endef
|
|
TARGET_DEVICES += comfast_cf-ew72
|
|
|
|
define Device/comfast_cf-wr650ac-v1
|
|
SOC := qca9558
|
|
DEVICE_VENDOR := COMFAST
|
|
DEVICE_MODEL := CF-WR650AC
|
|
DEVICE_VARIANT := v1
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
IMAGE_SIZE := 16128k
|
|
endef
|
|
TARGET_DEVICES += comfast_cf-wr650ac-v1
|
|
|
|
define Device/comfast_cf-wr650ac-v2
|
|
SOC := qca9558
|
|
DEVICE_VENDOR := COMFAST
|
|
DEVICE_MODEL := CF-WR650AC
|
|
DEVICE_VARIANT := v2
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
IMAGE_SIZE := 16000k
|
|
endef
|
|
TARGET_DEVICES += comfast_cf-wr650ac-v2
|
|
|
|
define Device/comfast_cf-wr752ac-v1
|
|
SOC := qca9531
|
|
DEVICE_VENDOR := COMFAST
|
|
DEVICE_MODEL := CF-WR752AC
|
|
DEVICE_VARIANT := v1
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca9888-ct \
|
|
-uboot-envtools
|
|
IMAGE_SIZE := 16192k
|
|
endef
|
|
TARGET_DEVICES += comfast_cf-wr752ac-v1
|
|
|
|
define Device/compex_wpj344-16m
|
|
SOC := ar9344
|
|
DEVICE_PACKAGES := kmod-usb2
|
|
IMAGE_SIZE := 16128k
|
|
DEVICE_VENDOR := Compex
|
|
DEVICE_MODEL := WPJ344
|
|
DEVICE_VARIANT := 16M
|
|
SUPPORTED_DEVICES += wpj344
|
|
IMAGES += cpximg-6a08.bin
|
|
IMAGE/cpximg-6a08.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | mkmylofw_16m 0x690 3
|
|
endef
|
|
TARGET_DEVICES += compex_wpj344-16m
|
|
|
|
define Device/compex_wpj531-16m
|
|
SOC := qca9531
|
|
DEVICE_PACKAGES := kmod-usb2
|
|
IMAGE_SIZE := 16128k
|
|
DEVICE_VENDOR := Compex
|
|
DEVICE_MODEL := WPJ531
|
|
DEVICE_VARIANT := 16M
|
|
SUPPORTED_DEVICES += wpj531
|
|
IMAGES += cpximg-7a03.bin cpximg-7a04.bin cpximg-7a06.bin cpximg-7a07.bin
|
|
IMAGE/cpximg-7a03.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | mkmylofw_16m 0x68a 2
|
|
IMAGE/cpximg-7a04.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | mkmylofw_16m 0x693 3
|
|
IMAGE/cpximg-7a06.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | mkmylofw_16m 0x693 3
|
|
IMAGE/cpximg-7a07.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | mkmylofw_16m 0x693 3
|
|
endef
|
|
TARGET_DEVICES += compex_wpj531-16m
|
|
|
|
define Device/compex_wpj558-16m
|
|
SOC := qca9558
|
|
IMAGE_SIZE := 16128k
|
|
DEVICE_VENDOR := Compex
|
|
DEVICE_MODEL := WPJ558
|
|
DEVICE_VARIANT := 16M
|
|
SUPPORTED_DEVICES += wpj558
|
|
IMAGES += cpximg-6a07.bin
|
|
IMAGE/cpximg-6a07.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
|
append-rootfs | pad-rootfs | mkmylofw_16m 0x691 3
|
|
DEVICE_PACKAGES := kmod-gpio-beeper
|
|
endef
|
|
TARGET_DEVICES += compex_wpj558-16m
|
|
|
|
define Device/compex_wpj563
|
|
SOC := qca9563
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-usb3
|
|
IMAGE_SIZE := 16128k
|
|
DEVICE_VENDOR := Compex
|
|
DEVICE_MODEL := WPJ563
|
|
SUPPORTED_DEVICES += wpj563
|
|
IMAGES += cpximg-7a02.bin
|
|
IMAGE/cpximg-7a02.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | mkmylofw_16m 0x694 2
|
|
endef
|
|
TARGET_DEVICES += compex_wpj563
|
|
|
|
define Device/devolo_dlan-pro-1200plus-ac
|
|
SOC := ar9344
|
|
DEVICE_VENDOR := devolo
|
|
DEVICE_MODEL := dLAN pro 1200+ WiFi ac
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
IMAGE_SIZE := 15872k
|
|
endef
|
|
TARGET_DEVICES += devolo_dlan-pro-1200plus-ac
|
|
|
|
define Device/devolo_dvl1200e
|
|
SOC := qca9558
|
|
DEVICE_VENDOR := devolo
|
|
DEVICE_MODEL := WiFi pro 1200e
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
IMAGE_SIZE := 15936k
|
|
endef
|
|
TARGET_DEVICES += devolo_dvl1200e
|
|
|
|
define Device/devolo_dvl1200i
|
|
SOC := qca9558
|
|
DEVICE_VENDOR := devolo
|
|
DEVICE_MODEL := WiFi pro 1200i
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
IMAGE_SIZE := 15936k
|
|
endef
|
|
TARGET_DEVICES += devolo_dvl1200i
|
|
|
|
define Device/devolo_dvl1750c
|
|
SOC := qca9558
|
|
DEVICE_VENDOR := devolo
|
|
DEVICE_MODEL := WiFi pro 1750c
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
IMAGE_SIZE := 15936k
|
|
endef
|
|
TARGET_DEVICES += devolo_dvl1750c
|
|
|
|
define Device/devolo_dvl1750e
|
|
SOC := qca9558
|
|
DEVICE_VENDOR := devolo
|
|
DEVICE_MODEL := WiFi pro 1750e
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
IMAGE_SIZE := 15936k
|
|
endef
|
|
TARGET_DEVICES += devolo_dvl1750e
|
|
|
|
define Device/devolo_dvl1750i
|
|
SOC := qca9558
|
|
DEVICE_VENDOR := devolo
|
|
DEVICE_MODEL := WiFi pro 1750i
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
IMAGE_SIZE := 15936k
|
|
endef
|
|
TARGET_DEVICES += devolo_dvl1750i
|
|
|
|
define Device/devolo_dvl1750x
|
|
SOC := qca9558
|
|
DEVICE_VENDOR := devolo
|
|
DEVICE_MODEL := WiFi pro 1750x
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
IMAGE_SIZE := 15936k
|
|
endef
|
|
TARGET_DEVICES += devolo_dvl1750x
|
|
|
|
define Device/devolo_magic-2-wifi
|
|
SOC := ar9344
|
|
DEVICE_VENDOR := devolo
|
|
DEVICE_MODEL := Magic 2 WiFi
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
IMAGE_SIZE := 15872k
|
|
endef
|
|
TARGET_DEVICES += devolo_magic-2-wifi
|
|
|
|
define Device/dlink_dap-13xx
|
|
SOC := qca9533
|
|
DEVICE_VENDOR := D-Link
|
|
DEVICE_PACKAGES += rssileds
|
|
IMAGE_SIZE := 7936k
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
|
append-rootfs | pad-rootfs | check-size | mkdapimg2 0xE0000
|
|
endef
|
|
|
|
define Device/dlink_dap-1330-a1
|
|
$(Device/dlink_dap-13xx)
|
|
DEVICE_MODEL := DAP-1330
|
|
DEVICE_VARIANT := A1
|
|
DAP_SIGNATURE := HONEYBEE-FIRMWARE-DAP-1330
|
|
SUPPORTED_DEVICES += dap-1330-a1
|
|
endef
|
|
TARGET_DEVICES += dlink_dap-1330-a1
|
|
|
|
define Device/dlink_dap-1365-a1
|
|
$(Device/dlink_dap-13xx)
|
|
DEVICE_MODEL := DAP-1365
|
|
DEVICE_VARIANT := A1
|
|
DAP_SIGNATURE := HONEYBEE-FIRMWARE-DAP-1365
|
|
endef
|
|
TARGET_DEVICES += dlink_dap-1365-a1
|
|
|
|
define Device/dlink_dap-2xxx
|
|
IMAGES += factory.img
|
|
IMAGE/factory.img := append-kernel | pad-offset 6144k 160 | \
|
|
append-rootfs | wrgg-pad-rootfs | mkwrggimg | check-size
|
|
IMAGE/sysupgrade.bin := append-kernel | mkwrggimg | \
|
|
pad-to $$$$(BLOCKSIZE) | append-rootfs | wrgg-pad-rootfs | \
|
|
check-size | append-metadata
|
|
KERNEL := kernel-bin | append-dtb | relocate-kernel | lzma
|
|
KERNEL_INITRAMFS := $$(KERNEL) | mkwrggimg
|
|
endef
|
|
|
|
define Device/dlink_dap-2230-a1
|
|
$(Device/dlink_dap-2xxx)
|
|
SOC := qca9533
|
|
DEVICE_VENDOR := D-Link
|
|
DEVICE_MODEL := DAP-2230
|
|
DEVICE_VARIANT := A1
|
|
IMAGE_SIZE := 15232k
|
|
DAP_SIGNATURE := wapn31_dkbs_dap2230
|
|
endef
|
|
TARGET_DEVICES += dlink_dap-2230-a1
|
|
|
|
define Device/dlink_dap-2660-a1
|
|
$(Device/dlink_dap-2xxx)
|
|
SOC := qca9557
|
|
DEVICE_VENDOR := D-Link
|
|
DEVICE_MODEL := DAP-2660
|
|
DEVICE_VARIANT := A1
|
|
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct
|
|
IMAGE_SIZE := 15232k
|
|
DAP_SIGNATURE := wapac09_dkbs_dap2660
|
|
endef
|
|
TARGET_DEVICES += dlink_dap-2660-a1
|
|
|
|
define Device/dlink_dap-2680-a1
|
|
$(Device/dlink_dap-2xxx)
|
|
SOC := qca9558
|
|
DEVICE_VENDOR := D-Link
|
|
DEVICE_MODEL := DAP-2680
|
|
DEVICE_VARIANT := A1
|
|
DEVICE_PACKAGES := ath10k-firmware-qca9984-ct kmod-ath10k-ct
|
|
IMAGE_SIZE := 15232k
|
|
DAP_SIGNATURE := wapac36_dkbs_dap2680
|
|
endef
|
|
TARGET_DEVICES += dlink_dap-2680-a1
|
|
|
|
define Device/dlink_dap-2695-a1
|
|
$(Device/dlink_dap-2xxx)
|
|
SOC := qca9558
|
|
DEVICE_VENDOR := D-Link
|
|
DEVICE_MODEL := DAP-2695
|
|
DEVICE_VARIANT := A1
|
|
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct
|
|
IMAGE_SIZE := 15360k
|
|
DAP_SIGNATURE := wapac02_dkbs_dap2695
|
|
SUPPORTED_DEVICES += dap-2695-a1
|
|
endef
|
|
TARGET_DEVICES += dlink_dap-2695-a1
|
|
|
|
define Device/dlink_dap-3320-a1
|
|
$(Device/dlink_dap-2xxx)
|
|
SOC := qca9533
|
|
DEVICE_VENDOR := D-Link
|
|
DEVICE_MODEL := DAP-3320
|
|
DEVICE_VARIANT := A1
|
|
IMAGE_SIZE := 15296k
|
|
DAP_SIGNATURE := wapn29_dkbs_dap3320
|
|
endef
|
|
TARGET_DEVICES += dlink_dap-3320-a1
|
|
|
|
define Device/dlink_dap-3662-a1
|
|
$(Device/dlink_dap-2xxx)
|
|
SOC := qca9558
|
|
DEVICE_VENDOR := D-Link
|
|
DEVICE_MODEL := DAP-3662
|
|
DEVICE_VARIANT := A1
|
|
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct
|
|
IMAGE_SIZE := 15296k
|
|
DAP_SIGNATURE := wapac11_dkbs_dap3662
|
|
endef
|
|
TARGET_DEVICES += dlink_dap-3662-a1
|
|
|
|
define Device/dlink_dch-g020-a1
|
|
SOC := qca9531
|
|
DEVICE_VENDOR := D-Link
|
|
DEVICE_MODEL := DCH-G020
|
|
DEVICE_VARIANT := A1
|
|
DEVICE_PACKAGES := kmod-gpio-pca953x kmod-i2c-gpio kmod-usb2 kmod-usb-acm
|
|
IMAGES += factory.bin
|
|
IMAGE_SIZE := 14784k
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
|
append-rootfs | pad-rootfs | check-size | mkdapimg2 0x20000
|
|
DAP_SIGNATURE := HONEYBEE-FIRMWARE-DCH-G020
|
|
endef
|
|
TARGET_DEVICES += dlink_dch-g020-a1
|
|
|
|
define Device/dlink_dir-505
|
|
SOC := ar9330
|
|
DEVICE_VENDOR := D-Link
|
|
DEVICE_MODEL := DIR-505
|
|
IMAGE_SIZE := 7680k
|
|
DEVICE_PACKAGES := kmod-usb-chipidea2
|
|
SUPPORTED_DEVICES += dir-505-a1
|
|
endef
|
|
TARGET_DEVICES += dlink_dir-505
|
|
|
|
define Device/dlink_dir-629-a1
|
|
$(Device/seama)
|
|
SOC := qca9558
|
|
IMAGE_SIZE := 7616k
|
|
DEVICE_VENDOR := D-Link
|
|
DEVICE_MODEL := DIR-629
|
|
DEVICE_VARIANT := A1
|
|
DEVICE_PACKAGES := -uboot-envtools
|
|
SEAMA_MTDBLOCK := 6
|
|
SEAMA_SIGNATURE := wrgn83_dlob.hans_dir629
|
|
endef
|
|
TARGET_DEVICES += dlink_dir-629-a1
|
|
|
|
define Device/dlink_dir-825-b1
|
|
SOC := ar7161
|
|
DEVICE_VENDOR := D-Link
|
|
DEVICE_MODEL := DIR-825
|
|
DEVICE_VARIANT := B1
|
|
DEVICE_PACKAGES := kmod-usb-ohci kmod-usb2 kmod-usb-ledtrig-usbport \
|
|
kmod-leds-reset kmod-owl-loader kmod-switch-rtl8366s
|
|
IMAGE_SIZE := 7808k
|
|
FACTORY_SIZE := 6144k
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin = append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | \
|
|
pad-rootfs | check-size $$$$(FACTORY_SIZE) | pad-to $$$$(FACTORY_SIZE) | \
|
|
append-string 01AP94-AR7161-RT-080619-00
|
|
endef
|
|
TARGET_DEVICES += dlink_dir-825-b1
|
|
|
|
define Device/dlink_dir-825-c1
|
|
SOC := ar9344
|
|
DEVICE_VENDOR := D-Link
|
|
DEVICE_MODEL := DIR-825
|
|
DEVICE_VARIANT := C1
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport kmod-leds-reset \
|
|
kmod-owl-loader
|
|
SUPPORTED_DEVICES += dir-825-c1
|
|
IMAGE_SIZE := 15936k
|
|
IMAGES := factory.bin sysupgrade.bin
|
|
IMAGE/default := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | \
|
|
pad-rootfs
|
|
IMAGE/factory.bin := $$(IMAGE/default) | pad-offset $$$$(IMAGE_SIZE) 26 | \
|
|
append-string 00DB120AR9344-RT-101214-00 | check-size
|
|
IMAGE/sysupgrade.bin := $$(IMAGE/default) | check-size | append-metadata
|
|
endef
|
|
TARGET_DEVICES += dlink_dir-825-c1
|
|
|
|
define Device/dlink_dir-835-a1
|
|
SOC := ar9344
|
|
DEVICE_VENDOR := D-Link
|
|
DEVICE_MODEL := DIR-835
|
|
DEVICE_VARIANT := A1
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-leds-reset kmod-owl-loader
|
|
SUPPORTED_DEVICES += dir-835-a1
|
|
IMAGE_SIZE := 15936k
|
|
IMAGES := factory.bin sysupgrade.bin
|
|
IMAGE/default := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | \
|
|
pad-rootfs
|
|
IMAGE/factory.bin := $$(IMAGE/default) | pad-offset $$$$(IMAGE_SIZE) 26 | \
|
|
append-string 00DB120AR9344-RT-101214-00 | check-size
|
|
IMAGE/sysupgrade.bin := $$(IMAGE/default) | check-size | append-metadata
|
|
endef
|
|
TARGET_DEVICES += dlink_dir-835-a1
|
|
|
|
define Device/dlink_dir-842-c
|
|
SOC := qca9563
|
|
DEVICE_VENDOR := D-Link
|
|
DEVICE_MODEL := DIR-842
|
|
KERNEL := kernel-bin | append-dtb | relocate-kernel | lzma
|
|
KERNEL_INITRAMFS := $$(KERNEL) | seama
|
|
IMAGES += factory.bin
|
|
SEAMA_MTDBLOCK := 5
|
|
SEAMA_SIGNATURE := wrgac65_dlink.2015_dir842
|
|
# 64 bytes offset:
|
|
# - 28 bytes seama_header
|
|
# - 36 bytes of META data (4-bytes aligned)
|
|
IMAGE/default := append-kernel | uImage lzma | \
|
|
pad-offset $$$$(BLOCKSIZE) 64 | append-rootfs
|
|
IMAGE/sysupgrade.bin := $$(IMAGE/default) | seama | pad-rootfs | \
|
|
check-size | append-metadata
|
|
IMAGE/factory.bin := $$(IMAGE/default) | pad-rootfs -x 64 | seama | \
|
|
seama-seal | check-size
|
|
IMAGE_SIZE := 15680k
|
|
endef
|
|
|
|
define Device/dlink_dir-842-c1
|
|
$(Device/dlink_dir-842-c)
|
|
DEVICE_VARIANT := C1
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct
|
|
endef
|
|
TARGET_DEVICES += dlink_dir-842-c1
|
|
|
|
define Device/dlink_dir-842-c2
|
|
$(Device/dlink_dir-842-c)
|
|
DEVICE_VARIANT := C2
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca9888-ct
|
|
endef
|
|
TARGET_DEVICES += dlink_dir-842-c2
|
|
|
|
define Device/dlink_dir-842-c3
|
|
$(Device/dlink_dir-842-c)
|
|
DEVICE_VARIANT := C3
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct
|
|
endef
|
|
TARGET_DEVICES += dlink_dir-842-c3
|
|
|
|
define Device/dlink_dir-859-a1
|
|
$(Device/seama)
|
|
SOC := qca9563
|
|
DEVICE_VENDOR := D-Link
|
|
DEVICE_MODEL := DIR-859
|
|
DEVICE_VARIANT := A1
|
|
IMAGE_SIZE := 15872k
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct-smallbuffers ath10k-firmware-qca988x-ct
|
|
SEAMA_SIGNATURE := wrgac37_dlink.2013gui_dir859
|
|
endef
|
|
TARGET_DEVICES += dlink_dir-859-a1
|
|
|
|
define Device/elecom_wrc-1750ghbk2-i
|
|
SOC := qca9563
|
|
DEVICE_VENDOR := ELECOM
|
|
DEVICE_MODEL := WRC-1750GHBK2-I/C
|
|
IMAGE_SIZE := 15808k
|
|
ifneq ($(CONFIG_TARGET_ROOTFS_INITRAMFS),)
|
|
ARTIFACTS := initramfs-factory.bin
|
|
ARTIFACT/initramfs-factory.bin := append-image initramfs-kernel.bin | \
|
|
pad-to 2 | edimax-header -b -s CSYS -m RN68 -f 0x70000 -S 0x01100000 | \
|
|
elecom-product-header WRC-1750GHBK2 | check-size
|
|
endif
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
endef
|
|
TARGET_DEVICES += elecom_wrc-1750ghbk2-i
|
|
|
|
define Device/elecom_wrc-300ghbk2-i
|
|
SOC := qca9563
|
|
DEVICE_VENDOR := ELECOM
|
|
DEVICE_MODEL := WRC-300GHBK2-I
|
|
IMAGE_SIZE := 7616k
|
|
ifneq ($(CONFIG_TARGET_ROOTFS_INITRAMFS),)
|
|
ARTIFACTS := initramfs-factory.bin
|
|
ARTIFACT/initramfs-factory.bin := append-image initramfs-kernel.bin | \
|
|
pad-to 2 | edimax-header -b -s CSYS -m RN51 -f 0x70000 -S 0x01100000 | \
|
|
elecom-product-header WRC-300GHBK2-I | check-size
|
|
endif
|
|
endef
|
|
TARGET_DEVICES += elecom_wrc-300ghbk2-i
|
|
|
|
define Device/embeddedwireless_balin
|
|
SOC := ar9344
|
|
DEVICE_VENDOR := Embedded Wireless
|
|
DEVICE_MODEL := Balin
|
|
DEVICE_PACKAGES := kmod-usb-chipidea2
|
|
IMAGE_SIZE := 16000k
|
|
endef
|
|
TARGET_DEVICES += embeddedwireless_balin
|
|
|
|
define Device/embeddedwireless_dorin
|
|
SOC := ar9331
|
|
DEVICE_VENDOR := Embedded Wireless
|
|
DEVICE_MODEL := Dorin
|
|
DEVICE_PACKAGES := kmod-usb-chipidea2
|
|
IMAGE_SIZE := 16000k
|
|
endef
|
|
TARGET_DEVICES += embeddedwireless_dorin
|
|
|
|
define Device/engenius_eap1200h
|
|
$(Device/senao_loader_okli)
|
|
SOC := qca9557
|
|
DEVICE_VENDOR := EnGenius
|
|
DEVICE_MODEL := EAP1200H
|
|
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct
|
|
IMAGE_SIZE := 11584k
|
|
LOADER_FLASH_OFFS := 0x220000
|
|
SENAO_IMGNAME := ar71xx-generic-eap1200h
|
|
endef
|
|
TARGET_DEVICES += engenius_eap1200h
|
|
|
|
define Device/engenius_eap1750h
|
|
$(Device/senao_loader_okli)
|
|
SOC := qca9558
|
|
DEVICE_VENDOR := EnGenius
|
|
DEVICE_MODEL := EAP1750H
|
|
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct
|
|
IMAGE_SIZE := 11584k
|
|
LOADER_FLASH_OFFS := 0x220000
|
|
SENAO_IMGNAME := ar71xx-generic-eap1750h
|
|
endef
|
|
TARGET_DEVICES += engenius_eap1750h
|
|
|
|
define Device/engenius_eap300-v2
|
|
$(Device/senao_loader_okli)
|
|
SOC := ar9341
|
|
DEVICE_VENDOR := EnGenius
|
|
DEVICE_MODEL := EAP300
|
|
DEVICE_VARIANT := v2
|
|
IMAGE_SIZE := 12096k
|
|
LOADER_FLASH_OFFS := 0x220000
|
|
SENAO_IMGNAME := senao-eap300v2
|
|
endef
|
|
TARGET_DEVICES += engenius_eap300-v2
|
|
|
|
define Device/engenius_eap600
|
|
$(Device/senao_loader_okli)
|
|
SOC := ar9344
|
|
DEVICE_VENDOR := EnGenius
|
|
DEVICE_MODEL := EAP600
|
|
IMAGE_SIZE := 12096k
|
|
LOADER_FLASH_OFFS := 0x220000
|
|
SENAO_IMGNAME := senao-eap600
|
|
endef
|
|
TARGET_DEVICES += engenius_eap600
|
|
|
|
define Device/engenius_ecb1200
|
|
SOC := qca9557
|
|
DEVICE_VENDOR := EnGenius
|
|
DEVICE_MODEL := ECB1200
|
|
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct
|
|
IMAGE_SIZE := 15680k
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
|
append-rootfs | pad-rootfs | check-size | \
|
|
senao-header -r 0x101 -p 0x6e -t 2
|
|
endef
|
|
TARGET_DEVICES += engenius_ecb1200
|
|
|
|
define Device/engenius_ecb1750
|
|
SOC := qca9558
|
|
DEVICE_VENDOR := EnGenius
|
|
DEVICE_MODEL := ECB1750
|
|
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct
|
|
IMAGE_SIZE := 15680k
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
|
append-rootfs | pad-rootfs | check-size | \
|
|
senao-header -r 0x101 -p 0x6d -t 2
|
|
endef
|
|
TARGET_DEVICES += engenius_ecb1750
|
|
|
|
define Device/engenius_ecb600
|
|
$(Device/senao_loader_okli)
|
|
SOC := ar9344
|
|
DEVICE_VENDOR := EnGenius
|
|
DEVICE_MODEL := ECB600
|
|
IMAGE_SIZE := 12096k
|
|
LOADER_FLASH_OFFS := 0x220000
|
|
SENAO_IMGNAME := senao-ecb600
|
|
endef
|
|
TARGET_DEVICES += engenius_ecb600
|
|
|
|
define Device/engenius_ens202ext-v1
|
|
$(Device/senao_loader_okli)
|
|
SOC := ar9341
|
|
DEVICE_VENDOR := EnGenius
|
|
DEVICE_MODEL := ENS202EXT
|
|
DEVICE_VARIANT := v1
|
|
DEVICE_PACKAGES := rssileds
|
|
IMAGE_SIZE := 12096k
|
|
LOADER_FLASH_OFFS := 0x220000
|
|
SENAO_IMGNAME := senao-ens202ext
|
|
endef
|
|
TARGET_DEVICES += engenius_ens202ext-v1
|
|
|
|
define Device/engenius_enstationac-v1
|
|
$(Device/senao_loader_okli)
|
|
SOC := qca9557
|
|
DEVICE_VENDOR := EnGenius
|
|
DEVICE_MODEL := EnStationAC
|
|
DEVICE_VARIANT := v1
|
|
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct rssileds
|
|
IMAGE_SIZE := 11584k
|
|
LOADER_FLASH_OFFS := 0x220000
|
|
SENAO_IMGNAME := ar71xx-generic-enstationac
|
|
endef
|
|
TARGET_DEVICES += engenius_enstationac-v1
|
|
|
|
define Device/engenius_epg5000
|
|
SOC := qca9558
|
|
DEVICE_VENDOR := EnGenius
|
|
DEVICE_MODEL := EPG5000
|
|
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct kmod-usb2
|
|
IMAGE_SIZE := 14656k
|
|
IMAGES += factory.dlf
|
|
IMAGE/factory.dlf := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
|
append-rootfs | pad-rootfs | check-size | \
|
|
senao-header -r 0x101 -p 0x71 -t 2
|
|
SUPPORTED_DEVICES += epg5000
|
|
endef
|
|
TARGET_DEVICES += engenius_epg5000
|
|
|
|
define Device/engenius_esr1200
|
|
SOC := qca9557
|
|
DEVICE_VENDOR := EnGenius
|
|
DEVICE_MODEL := ESR1200
|
|
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct kmod-usb2
|
|
IMAGE_SIZE := 14656k
|
|
IMAGES += factory.dlf
|
|
IMAGE/factory.dlf := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
|
append-rootfs | pad-rootfs | check-size | \
|
|
senao-header -r 0x101 -p 0x61 -t 2
|
|
SUPPORTED_DEVICES += esr1200 esr1750 engenius,esr1750
|
|
endef
|
|
TARGET_DEVICES += engenius_esr1200
|
|
|
|
define Device/engenius_esr1750
|
|
SOC := qca9558
|
|
DEVICE_VENDOR := EnGenius
|
|
DEVICE_MODEL := ESR1750
|
|
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct kmod-usb2
|
|
IMAGE_SIZE := 14656k
|
|
IMAGES += factory.dlf
|
|
IMAGE/factory.dlf := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
|
append-rootfs | pad-rootfs | check-size | \
|
|
senao-header -r 0x101 -p 0x62 -t 2
|
|
SUPPORTED_DEVICES += esr1750 esr1200 engenius,esr1200
|
|
endef
|
|
TARGET_DEVICES += engenius_esr1750
|
|
|
|
define Device/engenius_esr900
|
|
SOC := qca9558
|
|
DEVICE_VENDOR := EnGenius
|
|
DEVICE_MODEL := ESR900
|
|
DEVICE_PACKAGES := kmod-usb2
|
|
IMAGE_SIZE := 14656k
|
|
IMAGES += factory.dlf
|
|
IMAGE/factory.dlf := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
|
append-rootfs | pad-rootfs | check-size | \
|
|
senao-header -r 0x101 -p 0x4e -t 2
|
|
SUPPORTED_DEVICES += esr900
|
|
endef
|
|
TARGET_DEVICES += engenius_esr900
|
|
|
|
define Device/engenius_ews511ap
|
|
SOC := qca9531
|
|
DEVICE_VENDOR := EnGenius
|
|
DEVICE_MODEL := EWS511AP
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9887-ct
|
|
IMAGE_SIZE := 16000k
|
|
endef
|
|
TARGET_DEVICES += engenius_ews511ap
|
|
|
|
define Device/engenius_ews660ap
|
|
$(Device/senao_loader_okli)
|
|
SOC := qca9558
|
|
DEVICE_VENDOR := EnGenius
|
|
DEVICE_MODEL := EWS660AP
|
|
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct
|
|
IMAGE_SIZE := 11584k
|
|
LOADER_FLASH_OFFS := 0x220000
|
|
SENAO_IMGNAME := ar71xx-generic-ews660ap
|
|
endef
|
|
TARGET_DEVICES += engenius_ews660ap
|
|
|
|
define Device/enterasys_ws-ap3705i
|
|
SOC := ar9344
|
|
DEVICE_VENDOR := Enterasys
|
|
DEVICE_MODEL := WS-AP3705i
|
|
IMAGE_SIZE := 30528k
|
|
endef
|
|
TARGET_DEVICES += enterasys_ws-ap3705i
|
|
|
|
define Device/etactica_eg200
|
|
SOC := ar9331
|
|
DEVICE_VENDOR := eTactica
|
|
DEVICE_MODEL := EG200
|
|
DEVICE_PACKAGES := kmod-usb-chipidea2 kmod-ledtrig-oneshot \
|
|
kmod-usb-serial-ftdi kmod-usb-storage kmod-fs-ext4
|
|
IMAGE_SIZE := 16000k
|
|
SUPPORTED_DEVICES += rme-eg200
|
|
endef
|
|
TARGET_DEVICES += etactica_eg200
|
|
|
|
define Device/extreme-networks_ws-ap3805i
|
|
SOC := qca9557
|
|
BLOCKSIZE := 256k
|
|
DEVICE_VENDOR := Extreme Networks
|
|
DEVICE_MODEL := WS-AP3805i
|
|
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct
|
|
IMAGE_SIZE := 29440k
|
|
endef
|
|
TARGET_DEVICES += extreme-networks_ws-ap3805i
|
|
|
|
define Device/fortinet_fap-221-b
|
|
$(Device/senao_loader_okli)
|
|
SOC := ar9344
|
|
DEVICE_VENDOR := Fortinet
|
|
DEVICE_MODEL := FAP-221-B
|
|
FACTORY_IMG_NAME := FP221B-9.99-AP-build999-999999-patch99
|
|
IMAGE_SIZE := 9216k
|
|
LOADER_FLASH_OFFS := 0x040000
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
|
append-rootfs | pad-rootfs | \
|
|
check-size | pad-to $$$$(IMAGE_SIZE) | \
|
|
append-loader-okli-uimage $(1) | pad-to 10944k | \
|
|
gzip-filename $$$$(FACTORY_IMG_NAME)
|
|
endef
|
|
TARGET_DEVICES += fortinet_fap-221-b
|
|
|
|
define Device/glinet_6408
|
|
$(Device/tplink-8mlzma)
|
|
SOC := ar9331
|
|
DEVICE_VENDOR := GL.iNet
|
|
DEVICE_MODEL := 6408
|
|
DEVICE_PACKAGES := kmod-usb-chipidea2
|
|
IMAGE_SIZE := 8000k
|
|
TPLINK_HWID := 0x08000001
|
|
IMAGES := sysupgrade.bin
|
|
SUPPORTED_DEVICES += gl-inet
|
|
endef
|
|
TARGET_DEVICES += glinet_6408
|
|
|
|
define Device/glinet_6416
|
|
$(Device/tplink-16mlzma)
|
|
SOC := ar9331
|
|
DEVICE_VENDOR := GL.iNet
|
|
DEVICE_MODEL := 6416
|
|
DEVICE_PACKAGES := kmod-usb-chipidea2
|
|
IMAGE_SIZE := 16192k
|
|
TPLINK_HWID := 0x08000001
|
|
IMAGES := sysupgrade.bin
|
|
SUPPORTED_DEVICES += gl-inet
|
|
endef
|
|
TARGET_DEVICES += glinet_6416
|
|
|
|
define Device/glinet_gl-ar150
|
|
SOC := ar9330
|
|
DEVICE_VENDOR := GL.iNet
|
|
DEVICE_MODEL := GL-AR150
|
|
DEVICE_PACKAGES := kmod-usb-chipidea2
|
|
IMAGE_SIZE := 16000k
|
|
SUPPORTED_DEVICES += gl-ar150
|
|
endef
|
|
TARGET_DEVICES += glinet_gl-ar150
|
|
|
|
define Device/glinet_gl-ar300m-common-nor
|
|
SOC := qca9531
|
|
DEVICE_VENDOR := GL.iNet
|
|
DEVICE_PACKAGES := kmod-usb2
|
|
IMAGE_SIZE := 16000k
|
|
SUPPORTED_DEVICES += gl-ar300m
|
|
endef
|
|
|
|
define Device/glinet_gl-ar300m-lite
|
|
$(Device/glinet_gl-ar300m-common-nor)
|
|
DEVICE_MODEL := GL-AR300M
|
|
DEVICE_VARIANT := Lite
|
|
endef
|
|
TARGET_DEVICES += glinet_gl-ar300m-lite
|
|
|
|
define Device/glinet_gl-ar300m16
|
|
$(Device/glinet_gl-ar300m-common-nor)
|
|
DEVICE_MODEL := GL-AR300M16
|
|
endef
|
|
TARGET_DEVICES += glinet_gl-ar300m16
|
|
|
|
define Device/glinet_gl-ar750
|
|
SOC := qca9531
|
|
DEVICE_VENDOR := GL.iNet
|
|
DEVICE_MODEL := GL-AR750
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca9887-ct
|
|
IMAGE_SIZE := 16000k
|
|
SUPPORTED_DEVICES += gl-ar750
|
|
endef
|
|
TARGET_DEVICES += glinet_gl-ar750
|
|
|
|
define Device/glinet_gl-mifi
|
|
SOC := ar9331
|
|
DEVICE_VENDOR := GL.iNET
|
|
DEVICE_MODEL := GL-MiFi
|
|
DEVICE_PACKAGES := kmod-usb-chipidea2
|
|
IMAGE_SIZE := 16000k
|
|
SUPPORTED_DEVICES += gl-mifi
|
|
endef
|
|
TARGET_DEVICES += glinet_gl-mifi
|
|
|
|
define Device/glinet_gl-usb150
|
|
SOC := ar9331
|
|
DEVICE_VENDOR := GL.iNET
|
|
DEVICE_MODEL := GL-USB150
|
|
IMAGE_SIZE := 16000k
|
|
SUPPORTED_DEVICES += gl-usb150
|
|
endef
|
|
TARGET_DEVICES += glinet_gl-usb150
|
|
|
|
define Device/glinet_gl-x300b
|
|
SOC := qca9531
|
|
DEVICE_VENDOR := GL.iNet
|
|
DEVICE_MODEL := GL-X300B
|
|
DEVICE_PACKAGES := kmod-usb2
|
|
IMAGE_SIZE := 16000k
|
|
endef
|
|
TARGET_DEVICES += glinet_gl-x300b
|
|
|
|
define Device/glinet_gl-x750
|
|
SOC := qca9531
|
|
DEVICE_VENDOR := GL.iNet
|
|
DEVICE_MODEL := GL-X750
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca9887-ct
|
|
IMAGE_SIZE := 16000k
|
|
endef
|
|
TARGET_DEVICES += glinet_gl-x750
|
|
|
|
define Device/hak5_lan-turtle
|
|
$(Device/tplink-16mlzma)
|
|
SOC := ar9331
|
|
DEVICE_VENDOR := Hak5
|
|
DEVICE_MODEL := LAN Turtle
|
|
TPLINK_HWID := 0x5348334c
|
|
IMAGES := sysupgrade.bin
|
|
DEVICE_PACKAGES := kmod-usb-chipidea2 -iwinfo -kmod-ath9k -swconfig \
|
|
-uboot-envtools -wpad-basic-mbedtls
|
|
SUPPORTED_DEVICES += lan-turtle
|
|
endef
|
|
TARGET_DEVICES += hak5_lan-turtle
|
|
|
|
define Device/hak5_packet-squirrel
|
|
$(Device/tplink-16mlzma)
|
|
SOC := ar9331
|
|
DEVICE_VENDOR := Hak5
|
|
DEVICE_MODEL := Packet Squirrel
|
|
TPLINK_HWID := 0x5351524c
|
|
IMAGES := sysupgrade.bin
|
|
DEVICE_PACKAGES := kmod-usb-chipidea2 -iwinfo -kmod-ath9k -swconfig \
|
|
-uboot-envtools -wpad-basic-mbedtls
|
|
SUPPORTED_DEVICES += packet-squirrel
|
|
endef
|
|
TARGET_DEVICES += hak5_packet-squirrel
|
|
|
|
define Device/hak5_wifi-pineapple-nano
|
|
$(Device/tplink-16mlzma)
|
|
SOC := ar9331
|
|
DEVICE_VENDOR := Hak5
|
|
DEVICE_MODEL := WiFi Pineapple NANO
|
|
TPLINK_HWID := 0x4e414e4f
|
|
IMAGES := sysupgrade.bin
|
|
DEVICE_PACKAGES := kmod-ath9k-htc kmod-usb-chipidea2 kmod-usb-storage \
|
|
-swconfig -uboot-envtools
|
|
SUPPORTED_DEVICES += wifi-pineapple-nano
|
|
endef
|
|
TARGET_DEVICES += hak5_wifi-pineapple-nano
|
|
|
|
define Device/hiwifi_hc6361
|
|
SOC := ar9331
|
|
DEVICE_VENDOR := HiWiFi
|
|
DEVICE_MODEL := HC6361
|
|
DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-usb-chipidea2 kmod-usb-storage \
|
|
kmod-fs-ext4 kmod-nls-iso8859-1 e2fsprogs
|
|
BOARDNAME := HiWiFi-HC6361
|
|
KERNEL := kernel-bin | append-dtb | lzma | uImage lzma | pad-to $$(BLOCKSIZE)
|
|
IMAGE_SIZE := 16128k
|
|
endef
|
|
TARGET_DEVICES += hiwifi_hc6361
|
|
|
|
define Device/iodata_etg3-r
|
|
SOC := ar9342
|
|
DEVICE_VENDOR := I-O DATA
|
|
DEVICE_MODEL := ETG3-R
|
|
IMAGE_SIZE := 7680k
|
|
DEVICE_PACKAGES := -iwinfo -kmod-ath9k -wpad-basic-mbedtls
|
|
endef
|
|
TARGET_DEVICES += iodata_etg3-r
|
|
|
|
define Device/iodata_wn-ac1167dgr
|
|
SOC := qca9557
|
|
DEVICE_VENDOR := I-O DATA
|
|
DEVICE_MODEL := WN-AC1167DGR
|
|
IMAGE_SIZE := 14656k
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
|
append-rootfs | pad-rootfs | check-size | \
|
|
senao-header -r 0x30a -p 0x61 -t 2
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
endef
|
|
TARGET_DEVICES += iodata_wn-ac1167dgr
|
|
|
|
define Device/iodata_wn-ac1600dgr
|
|
SOC := qca9557
|
|
DEVICE_VENDOR := I-O DATA
|
|
DEVICE_MODEL := WN-AC1600DGR
|
|
IMAGE_SIZE := 14656k
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
|
append-rootfs | pad-rootfs | check-size | \
|
|
senao-header -r 0x30a -p 0x60 -t 2 -v 200
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
endef
|
|
TARGET_DEVICES += iodata_wn-ac1600dgr
|
|
|
|
define Device/iodata_wn-ac1600dgr2
|
|
SOC := qca9557
|
|
DEVICE_VENDOR := I-O DATA
|
|
DEVICE_MODEL := WN-AC1600DGR2/DGR3
|
|
IMAGE_SIZE := 14656k
|
|
IMAGES += dgr2-dgr3-factory.bin
|
|
IMAGE/dgr2-dgr3-factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
|
append-rootfs | pad-rootfs | check-size | \
|
|
senao-header -r 0x30a -p 0x60 -t 2 -v 200
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
endef
|
|
TARGET_DEVICES += iodata_wn-ac1600dgr2
|
|
|
|
define Device/iodata_wn-ag300dgr
|
|
SOC := ar1022
|
|
DEVICE_VENDOR := I-O DATA
|
|
DEVICE_MODEL := WN-AG300DGR
|
|
IMAGE_SIZE := 15424k
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
|
append-rootfs | pad-rootfs | check-size | \
|
|
senao-header -r 0x30a -p 0x47 -t 2
|
|
DEVICE_PACKAGES := kmod-usb2
|
|
endef
|
|
TARGET_DEVICES += iodata_wn-ag300dgr
|
|
|
|
define Device/jjplus_ja76pf2
|
|
SOC := ar7161
|
|
DEVICE_VENDOR := jjPlus
|
|
DEVICE_MODEL := JA76PF2
|
|
DEVICE_PACKAGES += -kmod-ath9k -swconfig -wpad-basic-mbedtls -uboot-envtools fconfig kmod-hwmon-lm75
|
|
LOADER_TYPE := bin
|
|
LOADER_FLASH_OFFS := 0x60000
|
|
COMPILE := loader-$(1).bin
|
|
COMPILE/loader-$(1).bin := loader-okli-compile | lzma | pad-to 128k
|
|
ARTIFACTS := loader.bin
|
|
ARTIFACT/loader.bin := append-loader-okli $(1)
|
|
IMAGES += firmware.bin
|
|
IMAGE/firmware.bin := append-kernel | uImage lzma -M 0x4f4b4c49 | pad-to $$$$(BLOCKSIZE) | \
|
|
append-rootfs | pad-rootfs | pad-to $$$$(BLOCKSIZE) | check-size
|
|
IMAGE/sysupgrade.bin := $$(IMAGE/firmware.bin) | \
|
|
sysupgrade-tar kernel=$$$$(KDIR)/loader-$(1).bin rootfs=$$$$@ | append-metadata
|
|
KERNEL := kernel-bin | append-dtb | lzma
|
|
KERNEL_INITRAMFS := kernel-bin | append-dtb
|
|
IMAGE_SIZE := 15872k
|
|
DEVICE_COMPAT_VERSION := 2.0
|
|
DEVICE_COMPAT_MESSAGE := Partition design has changed compared to older versions (19.07 and 21.02) \
|
|
due to kernel drivers restrictions. Upgrade via sysupgrade mechanism is one way operation. \
|
|
Downgrading OpenWrt version will involve usage of bootloader command line interface.
|
|
endef
|
|
TARGET_DEVICES += jjplus_ja76pf2
|
|
|
|
define Device/jjplus_jwap230
|
|
SOC := qca9558
|
|
DEVICE_VENDOR := jjPlus
|
|
DEVICE_MODEL := JWAP230
|
|
IMAGE_SIZE := 16000k
|
|
endef
|
|
TARGET_DEVICES += jjplus_jwap230
|
|
|
|
define Device/joyit_jt-or750i
|
|
SOC := qca9531
|
|
DEVICE_VENDOR := Joy-IT
|
|
DEVICE_MODEL := JT-OR750i
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9887-ct
|
|
IMAGE_SIZE := 16000k
|
|
endef
|
|
TARGET_DEVICES += joyit_jt-or750i
|
|
|
|
define Device/kuwfi_c910
|
|
$(Device/loader-okli-uimage)
|
|
SOC := qca9533
|
|
DEVICE_VENDOR := KuWFi
|
|
DEVICE_MODEL := C910
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-usb-net-cdc-ether comgt-ncm
|
|
LOADER_FLASH_OFFS := 0x50000
|
|
KERNEL := kernel-bin | append-dtb | lzma | uImage lzma -M 0x4f4b4c49
|
|
IMAGE_SIZE := 15936k
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
|
append-rootfs | pad-rootfs | check-size | pad-to 14528k | \
|
|
append-loader-okli-uimage $(1) | pad-to 64k
|
|
endef
|
|
TARGET_DEVICES += kuwfi_c910
|
|
|
|
define Device/letv_lba-047-ch
|
|
$(Device/loader-okli-uimage)
|
|
SOC := qca9531
|
|
DEVICE_VENDOR := Letv
|
|
DEVICE_MODEL := LBA-047-CH
|
|
DEVICE_PACKAGES := -uboot-envtools
|
|
FACTORY_SIZE := 14528k
|
|
IMAGE_SIZE := 15936k
|
|
LOADER_FLASH_OFFS := 0x50000
|
|
KERNEL := kernel-bin | append-dtb | lzma | uImage lzma -M 0x4f4b4c49
|
|
IMAGES += kernel.bin rootfs.bin
|
|
IMAGE/kernel.bin := append-loader-okli-uimage $(1) | pad-to 64k
|
|
IMAGE/rootfs.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
|
append-rootfs | pad-rootfs | check-size $$$$(FACTORY_SIZE)
|
|
endef
|
|
TARGET_DEVICES += letv_lba-047-ch
|
|
|
|
define Device/librerouter_librerouter-v1
|
|
SOC := qca9558
|
|
DEVICE_VENDOR := Librerouter
|
|
DEVICE_MODEL := LibreRouter
|
|
DEVICE_VARIANT := v1
|
|
IMAGE_SIZE := 7936k
|
|
DEVICE_PACKAGES := kmod-usb2
|
|
endef
|
|
TARGET_DEVICES += librerouter_librerouter-v1
|
|
|
|
define Device/meraki_mr12
|
|
SOC := ar7242
|
|
DEVICE_VENDOR := Meraki
|
|
DEVICE_MODEL := MR12
|
|
IMAGE_SIZE := 15616k
|
|
DEVICE_PACKAGES := kmod-owl-loader rssileds
|
|
SUPPORTED_DEVICES += mr12
|
|
DEVICE_COMPAT_VERSION := 2.0
|
|
DEVICE_COMPAT_MESSAGE := Partitions differ from ar71xx version of MR12. Image format is incompatible. \
|
|
To use sysupgrade, you must change /lib/update/common.sh::get_image to prepend 128K zeroes to this image, \
|
|
and change the bootcmd in u-boot to "bootm 0xbf0a0000". After that, you can use "sysupgrade -F -n". \
|
|
Make sure you do not keep your old config, as ethernet setup is not compatible either. \
|
|
For more details, see the OpenWrt Wiki: https://openwrt.org/toh/meraki/MR12, \
|
|
or the commit message of the MR12 ath79 port on git.openwrt.org.
|
|
endef
|
|
TARGET_DEVICES += meraki_mr12
|
|
|
|
define Device/meraki_mr16
|
|
SOC := ar7161
|
|
DEVICE_VENDOR := Meraki
|
|
DEVICE_MODEL := MR16
|
|
IMAGE_SIZE := 15616k
|
|
DEVICE_PACKAGES := kmod-owl-loader
|
|
SUPPORTED_DEVICES += mr16
|
|
DEVICE_COMPAT_VERSION := 2.0
|
|
DEVICE_COMPAT_MESSAGE := Partitions differ from ar71xx version of MR16. Image format is incompatible. \
|
|
To use sysupgrade, you must change /lib/update/common.sh::get_image to prepend 128K zeroes to this image, \
|
|
and change the bootcmd in u-boot to "bootm 0xbf0a0000". After that, you can use "sysupgrade -F". \
|
|
For more details, see the OpenWrt Wiki: https://openwrt.org/toh/meraki/mr16, \
|
|
or the commit message of the MR16 ath79 port on git.openwrt.org.
|
|
endef
|
|
TARGET_DEVICES += meraki_mr16
|
|
|
|
define Device/mercury_mw4530r-v1
|
|
$(Device/tplink-8mlzma)
|
|
SOC := ar9344
|
|
DEVICE_VENDOR := Mercury
|
|
DEVICE_MODEL := MW4530R
|
|
DEVICE_VARIANT := v1
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport
|
|
TPLINK_HWID := 0x45300001
|
|
SUPPORTED_DEVICES += tl-wdr4300
|
|
endef
|
|
TARGET_DEVICES += mercury_mw4530r-v1
|
|
|
|
define Device/nec_wx1200cr
|
|
DEVICE_VENDOR := NEC
|
|
IMAGE/default := append-kernel | pad-offset $$$$(BLOCKSIZE) 64 | append-rootfs
|
|
IMAGE/sysupgrade.bin := $$(IMAGE/default) | seama | pad-rootfs | \
|
|
check-size | append-metadata
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct
|
|
endef
|
|
|
|
define Device/nec_wf1200cr
|
|
$(Device/nec_wx1200cr)
|
|
SOC := qca9561
|
|
DEVICE_MODEL := Aterm WF1200CR
|
|
IMAGE_SIZE := 7680k
|
|
SEAMA_MTDBLOCK := 5
|
|
SEAMA_SIGNATURE := wrgac62_necpf.2016gui_wf1200cr
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := $$(IMAGE/default) | pad-rootfs -x 64 | seama | \
|
|
seama-seal | nec-enc ryztfyutcrqqo69d | check-size
|
|
endef
|
|
TARGET_DEVICES += nec_wf1200cr
|
|
|
|
define Device/nec_wg1200cr
|
|
$(Device/nec_wx1200cr)
|
|
SOC := qca9563
|
|
DEVICE_MODEL := Aterm WG1200CR
|
|
IMAGE_SIZE := 7616k
|
|
SEAMA_MTDBLOCK := 6
|
|
SEAMA_SIGNATURE := wrgac72_necpf.2016gui_wg1200cr
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := $$(IMAGE/default) | pad-rootfs -x 64 | seama | \
|
|
seama-seal | nec-enc 9gsiy9nzep452pad | check-size
|
|
endef
|
|
TARGET_DEVICES += nec_wg1200cr
|
|
|
|
define Device/nec_wg800hp
|
|
SOC := qca9563
|
|
DEVICE_VENDOR := NEC
|
|
DEVICE_MODEL := Aterm WG800HP
|
|
IMAGE_SIZE := 7104k
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
|
append-rootfs | pad-rootfs | check-size | \
|
|
xor-image -p 6A57190601121E4C004C1E1201061957 -x | nec-fw LASER_ATERM
|
|
DEVICE_PACKAGES := kmod-ath10k-ct-smallbuffers ath10k-firmware-qca9887-ct-full-htt
|
|
endef
|
|
TARGET_DEVICES += nec_wg800hp
|
|
|
|
define Device/netgear_ex7300
|
|
SOC := qca9558
|
|
DEVICE_VENDOR := NETGEAR
|
|
DEVICE_MODEL := EX7300
|
|
DEVICE_ALT0_VENDOR := NETGEAR
|
|
DEVICE_ALT0_MODEL := EX6400
|
|
NETGEAR_BOARD_ID := EX7300series
|
|
NETGEAR_HW_ID := 29765104+16+0+128
|
|
IMAGE_SIZE := 15552k
|
|
IMAGES += factory.img
|
|
IMAGE/default := append-kernel | pad-offset $$$$(BLOCKSIZE) 64 | \
|
|
netgear-rootfs | pad-rootfs
|
|
IMAGE/sysupgrade.bin := $$(IMAGE/default) | check-size | append-metadata
|
|
IMAGE/factory.img := $$(IMAGE/default) | netgear-dni | check-size
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca99x0-ct
|
|
SUPPORTED_DEVICES += netgear,ex6400
|
|
endef
|
|
TARGET_DEVICES += netgear_ex7300
|
|
|
|
define Device/netgear_ex7300-v2
|
|
SOC := qcn5502
|
|
DEVICE_VENDOR := NETGEAR
|
|
DEVICE_MODEL := EX7300
|
|
DEVICE_VARIANT := v2
|
|
DEVICE_ALT0_VENDOR := NETGEAR
|
|
DEVICE_ALT0_MODEL := EX6250
|
|
DEVICE_ALT1_VENDOR := NETGEAR
|
|
DEVICE_ALT1_MODEL := EX6400
|
|
DEVICE_ALT1_VARIANT := v2
|
|
DEVICE_ALT2_VENDOR := NETGEAR
|
|
DEVICE_ALT2_MODEL := EX6410
|
|
DEVICE_ALT3_VENDOR := NETGEAR
|
|
DEVICE_ALT3_MODEL := EX6420
|
|
DEVICE_ALT4_VENDOR := NETGEAR
|
|
DEVICE_ALT4_MODEL := EX7320
|
|
NETGEAR_BOARD_ID := EX7300v2series
|
|
NETGEAR_HW_ID := 29765907+16+0+128
|
|
IMAGE_SIZE := 14528k
|
|
IMAGES += factory.img
|
|
IMAGE/default := append-kernel | pad-offset $$$$(BLOCKSIZE) 64 | \
|
|
netgear-rootfs | pad-rootfs
|
|
IMAGE/sysupgrade.bin := $$(IMAGE/default) | check-size | append-metadata
|
|
IMAGE/factory.img := $$(IMAGE/default) | check-size | netgear-dni
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9984-ct
|
|
endef
|
|
TARGET_DEVICES += netgear_ex7300-v2
|
|
|
|
define Device/netgear_wndap360
|
|
$(Device/netgear_generic)
|
|
SOC := ar7161
|
|
DEVICE_MODEL := WNDAP360
|
|
DEVICE_PACKAGES := kmod-leds-reset
|
|
IMAGE_SIZE := 7744k
|
|
BLOCKSIZE := 256k
|
|
KERNEL := kernel-bin | append-dtb | gzip | uImage gzip
|
|
KERNEL_INITRAMFS := kernel-bin | append-dtb | uImage none
|
|
IMAGES := sysupgrade.bin
|
|
IMAGE/sysupgrade.bin := append-kernel | pad-to 64k | append-rootfs | pad-rootfs | \
|
|
check-size | append-metadata
|
|
endef
|
|
TARGET_DEVICES += netgear_wndap360
|
|
|
|
define Device/netgear_wndr3x00
|
|
$(Device/netgear_generic)
|
|
SOC := ar7161
|
|
DEVICE_PACKAGES := kmod-usb-ohci kmod-usb2 kmod-usb-ledtrig-usbport \
|
|
kmod-leds-reset kmod-owl-loader kmod-switch-rtl8366s
|
|
endef
|
|
|
|
define Device/netgear_wndr3700
|
|
$(Device/netgear_wndr3x00)
|
|
DEVICE_MODEL := WNDR3700
|
|
DEVICE_VARIANT := v1
|
|
UIMAGE_MAGIC := 0x33373030
|
|
NETGEAR_BOARD_ID := WNDR3700
|
|
IMAGE_SIZE := 7680k
|
|
IMAGES += factory-NA.img
|
|
IMAGE/factory-NA.img := $$(IMAGE/default) | netgear-dni NA | \
|
|
check-size
|
|
SUPPORTED_DEVICES += wndr3700
|
|
endef
|
|
TARGET_DEVICES += netgear_wndr3700
|
|
|
|
define Device/netgear_wndr3700-v2
|
|
$(Device/netgear_wndr3x00)
|
|
DEVICE_MODEL := WNDR3700
|
|
DEVICE_VARIANT := v2
|
|
UIMAGE_MAGIC := 0x33373031
|
|
NETGEAR_BOARD_ID := WNDR3700v2
|
|
NETGEAR_HW_ID := 29763654+16+64
|
|
IMAGE_SIZE := 15872k
|
|
SUPPORTED_DEVICES += wndr3700 netgear,wndr3700v2
|
|
endef
|
|
TARGET_DEVICES += netgear_wndr3700-v2
|
|
|
|
define Device/netgear_wndr3800
|
|
$(Device/netgear_wndr3x00)
|
|
DEVICE_MODEL := WNDR3800
|
|
UIMAGE_MAGIC := 0x33373031
|
|
NETGEAR_BOARD_ID := WNDR3800
|
|
NETGEAR_HW_ID := 29763654+16+128
|
|
IMAGE_SIZE := 15872k
|
|
SUPPORTED_DEVICES += wndr3700
|
|
endef
|
|
TARGET_DEVICES += netgear_wndr3800
|
|
|
|
define Device/netgear_wndr3800ch
|
|
$(Device/netgear_wndr3x00)
|
|
DEVICE_MODEL := WNDR3800CH
|
|
UIMAGE_MAGIC := 0x33373031
|
|
NETGEAR_BOARD_ID := WNDR3800CH
|
|
NETGEAR_HW_ID := 29763654+16+128
|
|
IMAGE_SIZE := 15872k
|
|
SUPPORTED_DEVICES += wndr3700
|
|
endef
|
|
TARGET_DEVICES += netgear_wndr3800ch
|
|
|
|
define Device/netgear_wndrmac-v1
|
|
$(Device/netgear_wndr3x00)
|
|
DEVICE_MODEL := WNDRMAC
|
|
DEVICE_VARIANT := v1
|
|
UIMAGE_MAGIC := 0x33373031
|
|
NETGEAR_BOARD_ID := WNDRMAC
|
|
NETGEAR_HW_ID := 29763654+16+64
|
|
IMAGE_SIZE := 15872k
|
|
SUPPORTED_DEVICES += wndr3700
|
|
endef
|
|
TARGET_DEVICES += netgear_wndrmac-v1
|
|
|
|
define Device/netgear_wndrmac-v2
|
|
$(Device/netgear_wndr3x00)
|
|
DEVICE_MODEL := WNDRMAC
|
|
DEVICE_VARIANT := v2
|
|
UIMAGE_MAGIC := 0x33373031
|
|
NETGEAR_BOARD_ID := WNDRMACv2
|
|
NETGEAR_HW_ID := 29763654+16+128
|
|
IMAGE_SIZE := 15872k
|
|
SUPPORTED_DEVICES += wndr3700
|
|
endef
|
|
TARGET_DEVICES += netgear_wndrmac-v2
|
|
|
|
define Device/netgear_wnr2200_common
|
|
$(Device/netgear_generic)
|
|
SOC := ar7241
|
|
DEVICE_MODEL := WNR2200
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport
|
|
UIMAGE_MAGIC := 0x32323030
|
|
NETGEAR_BOARD_ID := wnr2200
|
|
endef
|
|
|
|
define Device/netgear_wnr2200-8m
|
|
$(Device/netgear_wnr2200_common)
|
|
DEVICE_VARIANT := 8M
|
|
NETGEAR_HW_ID := 29763600+08+64
|
|
IMAGE_SIZE := 7808k
|
|
IMAGES += factory-NA.img
|
|
IMAGE/factory-NA.img := $$(IMAGE/default) | netgear-dni NA | \
|
|
check-size
|
|
SUPPORTED_DEVICES += wnr2200
|
|
endef
|
|
TARGET_DEVICES += netgear_wnr2200-8m
|
|
|
|
define Device/netgear_wnr2200-16m
|
|
$(Device/netgear_wnr2200_common)
|
|
DEVICE_VARIANT := 16M
|
|
DEVICE_ALT0_VENDOR := NETGEAR
|
|
DEVICE_ALT0_MODEL := WNR2200
|
|
DEVICE_ALT0_VARIANT := CN/RU
|
|
NETGEAR_HW_ID :=
|
|
IMAGE_SIZE := 16000k
|
|
endef
|
|
TARGET_DEVICES += netgear_wnr2200-16m
|
|
|
|
define Device/ocedo_koala
|
|
SOC := qca9558
|
|
DEVICE_VENDOR := Ocedo
|
|
DEVICE_MODEL := Koala
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
SUPPORTED_DEVICES += koala
|
|
IMAGE_SIZE := 14848k
|
|
endef
|
|
TARGET_DEVICES += ocedo_koala
|
|
|
|
define Device/ocedo_raccoon
|
|
SOC := ar9344
|
|
DEVICE_VENDOR := Ocedo
|
|
DEVICE_MODEL := Raccoon
|
|
IMAGE_SIZE := 14848k
|
|
endef
|
|
TARGET_DEVICES += ocedo_raccoon
|
|
|
|
define Device/ocedo_ursus
|
|
SOC := qca9558
|
|
DEVICE_VENDOR := Ocedo
|
|
DEVICE_MODEL := Ursus
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
IMAGE_SIZE := 14848k
|
|
endef
|
|
TARGET_DEVICES += ocedo_ursus
|
|
|
|
define Device/onion_omega
|
|
$(Device/tplink-16mlzma)
|
|
SOC := ar9331
|
|
DEVICE_VENDOR := Onion
|
|
DEVICE_MODEL := Omega
|
|
DEVICE_PACKAGES := kmod-usb-chipidea2
|
|
SUPPORTED_DEVICES += onion-omega
|
|
KERNEL_INITRAMFS := kernel-bin | append-dtb | lzma | uImage lzma
|
|
IMAGE_SIZE := 16192k
|
|
TPLINK_HWID := 0x04700001
|
|
endef
|
|
TARGET_DEVICES += onion_omega
|
|
|
|
define Device/openmesh_common_64k
|
|
DEVICE_VENDOR := OpenMesh
|
|
DEVICE_PACKAGES := uboot-envtools
|
|
IMAGE_SIZE := 7808k
|
|
OPENMESH_CE_TYPE :=
|
|
KERNEL := kernel-bin | append-dtb | lzma | uImage lzma | \
|
|
pad-to $$(BLOCKSIZE)
|
|
IMAGE/sysupgrade.bin := append-rootfs | pad-rootfs | \
|
|
openmesh-image ce_type=$$$$(OPENMESH_CE_TYPE) | append-metadata
|
|
endef
|
|
|
|
define Device/openmesh_common_256k
|
|
DEVICE_VENDOR := OpenMesh
|
|
DEVICE_PACKAGES := uboot-envtools
|
|
IMAGE_SIZE := 7168k
|
|
BLOCKSIZE := 256k
|
|
OPENMESH_CE_TYPE :=
|
|
KERNEL := kernel-bin | append-dtb | lzma | uImage lzma | \
|
|
pad-to $$(BLOCKSIZE)
|
|
IMAGE/sysupgrade.bin := append-rootfs | pad-rootfs | \
|
|
openmesh-image ce_type=$$$$(OPENMESH_CE_TYPE) | append-metadata
|
|
endef
|
|
|
|
define Device/openmesh_a40
|
|
$(Device/openmesh_common_64k)
|
|
SOC := qca9558
|
|
DEVICE_MODEL := A40
|
|
DEVICE_PACKAGES += kmod-ath10k-ct ath10k-firmware-qca988x-ct kmod-usb2
|
|
OPENMESH_CE_TYPE := A60
|
|
SUPPORTED_DEVICES += a40
|
|
endef
|
|
TARGET_DEVICES += openmesh_a40
|
|
|
|
define Device/openmesh_a60
|
|
$(Device/openmesh_common_64k)
|
|
SOC := qca9558
|
|
DEVICE_MODEL := A60
|
|
DEVICE_PACKAGES += kmod-ath10k-ct ath10k-firmware-qca988x-ct kmod-usb2
|
|
OPENMESH_CE_TYPE := A60
|
|
SUPPORTED_DEVICES += a60
|
|
endef
|
|
TARGET_DEVICES += openmesh_a60
|
|
|
|
define Device/openmesh_mr600-v1
|
|
$(Device/openmesh_common_64k)
|
|
SOC := ar9344
|
|
DEVICE_MODEL := MR600
|
|
DEVICE_VARIANT := v1
|
|
OPENMESH_CE_TYPE := MR600
|
|
SUPPORTED_DEVICES += mr600
|
|
endef
|
|
TARGET_DEVICES += openmesh_mr600-v1
|
|
|
|
define Device/openmesh_mr600-v2
|
|
$(Device/openmesh_common_64k)
|
|
SOC := ar9344
|
|
DEVICE_MODEL := MR600
|
|
DEVICE_VARIANT := v2
|
|
OPENMESH_CE_TYPE := MR600
|
|
SUPPORTED_DEVICES += mr600v2
|
|
endef
|
|
TARGET_DEVICES += openmesh_mr600-v2
|
|
|
|
define Device/openmesh_mr900-v1
|
|
$(Device/openmesh_common_64k)
|
|
SOC := qca9558
|
|
DEVICE_MODEL := MR900
|
|
DEVICE_VARIANT := v1
|
|
OPENMESH_CE_TYPE := MR900
|
|
SUPPORTED_DEVICES += mr900
|
|
endef
|
|
TARGET_DEVICES += openmesh_mr900-v1
|
|
|
|
define Device/openmesh_mr900-v2
|
|
$(Device/openmesh_common_64k)
|
|
SOC := qca9558
|
|
DEVICE_MODEL := MR900
|
|
DEVICE_VARIANT := v2
|
|
OPENMESH_CE_TYPE := MR900
|
|
SUPPORTED_DEVICES += mr900v2
|
|
endef
|
|
TARGET_DEVICES += openmesh_mr900-v2
|
|
|
|
define Device/openmesh_mr1750-v1
|
|
$(Device/openmesh_common_64k)
|
|
SOC := qca9558
|
|
DEVICE_MODEL := MR1750
|
|
DEVICE_VARIANT := v1
|
|
DEVICE_PACKAGES += kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
OPENMESH_CE_TYPE := MR1750
|
|
SUPPORTED_DEVICES += mr1750
|
|
endef
|
|
TARGET_DEVICES += openmesh_mr1750-v1
|
|
|
|
define Device/openmesh_mr1750-v2
|
|
$(Device/openmesh_common_64k)
|
|
SOC := qca9558
|
|
DEVICE_MODEL := MR1750
|
|
DEVICE_VARIANT := v2
|
|
DEVICE_PACKAGES += kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
OPENMESH_CE_TYPE := MR1750
|
|
SUPPORTED_DEVICES += mr1750v2
|
|
endef
|
|
TARGET_DEVICES += openmesh_mr1750-v2
|
|
|
|
define Device/openmesh_om2p-v1
|
|
$(Device/openmesh_common_256k)
|
|
SOC := ar7240
|
|
DEVICE_MODEL := OM2P
|
|
DEVICE_VARIANT := v1
|
|
OPENMESH_CE_TYPE := OM2P
|
|
SUPPORTED_DEVICES += om2p
|
|
endef
|
|
TARGET_DEVICES += openmesh_om2p-v1
|
|
|
|
define Device/openmesh_om2p-v2
|
|
$(Device/openmesh_common_256k)
|
|
SOC := ar9330
|
|
DEVICE_MODEL := OM2P
|
|
DEVICE_VARIANT := v2
|
|
OPENMESH_CE_TYPE := OM2P
|
|
SUPPORTED_DEVICES += om2pv2
|
|
endef
|
|
TARGET_DEVICES += openmesh_om2p-v2
|
|
|
|
define Device/openmesh_om2p-v4
|
|
$(Device/openmesh_common_256k)
|
|
SOC := qca9533
|
|
DEVICE_MODEL := OM2P
|
|
DEVICE_VARIANT := v4
|
|
OPENMESH_CE_TYPE := OM2P
|
|
SUPPORTED_DEVICES += om2pv4
|
|
endef
|
|
TARGET_DEVICES += openmesh_om2p-v4
|
|
|
|
define Device/openmesh_om2p-hs-v1
|
|
$(Device/openmesh_common_256k)
|
|
SOC := ar9341
|
|
DEVICE_MODEL := OM2P-HS
|
|
DEVICE_VARIANT := v1
|
|
OPENMESH_CE_TYPE := OM2P
|
|
SUPPORTED_DEVICES += om2p-hs
|
|
endef
|
|
TARGET_DEVICES += openmesh_om2p-hs-v1
|
|
|
|
define Device/openmesh_om2p-hs-v2
|
|
$(Device/openmesh_common_256k)
|
|
SOC := ar9341
|
|
DEVICE_MODEL := OM2P-HS
|
|
DEVICE_VARIANT := v2
|
|
OPENMESH_CE_TYPE := OM2P
|
|
SUPPORTED_DEVICES += om2p-hsv2
|
|
endef
|
|
TARGET_DEVICES += openmesh_om2p-hs-v2
|
|
|
|
define Device/openmesh_om2p-hs-v3
|
|
$(Device/openmesh_common_256k)
|
|
SOC := ar9341
|
|
DEVICE_MODEL := OM2P-HS
|
|
DEVICE_VARIANT := v3
|
|
OPENMESH_CE_TYPE := OM2P
|
|
SUPPORTED_DEVICES += om2p-hsv3
|
|
endef
|
|
TARGET_DEVICES += openmesh_om2p-hs-v3
|
|
|
|
define Device/openmesh_om2p-hs-v4
|
|
$(Device/openmesh_common_256k)
|
|
SOC := qca9533
|
|
DEVICE_MODEL := OM2P-HS
|
|
DEVICE_VARIANT := v4
|
|
OPENMESH_CE_TYPE := OM2P
|
|
SUPPORTED_DEVICES += om2p-hsv4
|
|
endef
|
|
TARGET_DEVICES += openmesh_om2p-hs-v4
|
|
|
|
define Device/openmesh_om2p-lc
|
|
$(Device/openmesh_common_256k)
|
|
SOC := ar9330
|
|
DEVICE_MODEL := OM2P-LC
|
|
OPENMESH_CE_TYPE := OM2P
|
|
SUPPORTED_DEVICES += om2p-lc
|
|
endef
|
|
TARGET_DEVICES += openmesh_om2p-lc
|
|
|
|
define Device/openmesh_om5p
|
|
$(Device/openmesh_common_64k)
|
|
SOC := ar9344
|
|
DEVICE_MODEL := OM5P
|
|
OPENMESH_CE_TYPE := OM5P
|
|
SUPPORTED_DEVICES += om5p
|
|
endef
|
|
TARGET_DEVICES += openmesh_om5p
|
|
|
|
define Device/openmesh_om5p-ac-v1
|
|
$(Device/openmesh_common_64k)
|
|
SOC := qca9558
|
|
DEVICE_MODEL := OM5P-AC
|
|
DEVICE_VARIANT := v1
|
|
DEVICE_PACKAGES += kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
OPENMESH_CE_TYPE := OM5PAC
|
|
SUPPORTED_DEVICES += om5p-ac
|
|
endef
|
|
TARGET_DEVICES += openmesh_om5p-ac-v1
|
|
|
|
define Device/openmesh_om5p-ac-v2
|
|
$(Device/openmesh_common_64k)
|
|
SOC := qca9558
|
|
DEVICE_MODEL := OM5P-AC
|
|
DEVICE_VARIANT := v2
|
|
DEVICE_PACKAGES += kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
OPENMESH_CE_TYPE := OM5PAC
|
|
SUPPORTED_DEVICES += om5p-acv2
|
|
endef
|
|
TARGET_DEVICES += openmesh_om5p-ac-v2
|
|
|
|
define Device/openmesh_om5p-an
|
|
$(Device/openmesh_common_64k)
|
|
SOC := ar9344
|
|
DEVICE_MODEL := OM5P-AN
|
|
OPENMESH_CE_TYPE := OM5P
|
|
SUPPORTED_DEVICES += om5p-an
|
|
endef
|
|
TARGET_DEVICES += openmesh_om5p-an
|
|
|
|
define Device/pcs_cap324
|
|
SOC := ar9344
|
|
DEVICE_VENDOR := PowerCloud Systems
|
|
DEVICE_MODEL := CAP324
|
|
IMAGE_SIZE := 16000k
|
|
SUPPORTED_DEVICES += cap324
|
|
endef
|
|
TARGET_DEVICES += pcs_cap324
|
|
|
|
define Device/pcs_cr3000
|
|
SOC := ar9341
|
|
DEVICE_VENDOR := PowerCloud Systems
|
|
DEVICE_MODEL := CR3000
|
|
IMAGE_SIZE := 7808k
|
|
SUPPORTED_DEVICES += cr3000
|
|
endef
|
|
TARGET_DEVICES += pcs_cr3000
|
|
|
|
define Device/pcs_cr5000
|
|
SOC := ar9344
|
|
DEVICE_VENDOR := PowerCloud Systems
|
|
DEVICE_MODEL := CR5000
|
|
DEVICE_PACKAGES := kmod-usb2
|
|
IMAGE_SIZE := 7808k
|
|
SUPPORTED_DEVICES += cr5000
|
|
endef
|
|
TARGET_DEVICES += pcs_cr5000
|
|
|
|
define Device/phicomm_k2t
|
|
SOC := qca9563
|
|
DEVICE_VENDOR := Phicomm
|
|
DEVICE_MODEL := K2T
|
|
IMAGE_SIZE := 15744k
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | \
|
|
check-size | append-metadata
|
|
DEVICE_PACKAGES := kmod-leds-reset kmod-ath10k-ct-smallbuffers ath10k-firmware-qca9888-ct
|
|
endef
|
|
TARGET_DEVICES += phicomm_k2t
|
|
|
|
define Device/pisen_ts-d084
|
|
$(Device/tplink-8mlzma)
|
|
SOC := ar9331
|
|
DEVICE_VENDOR := PISEN
|
|
DEVICE_MODEL := TS-D084
|
|
DEVICE_PACKAGES := kmod-usb-chipidea2
|
|
TPLINK_HWID := 0x07030101
|
|
endef
|
|
TARGET_DEVICES += pisen_ts-d084
|
|
|
|
define Device/pisen_wmb001n
|
|
$(Device/loader-okli-uimage)
|
|
SOC := ar9341
|
|
DEVICE_VENDOR := PISEN
|
|
DEVICE_MODEL := WMB001N
|
|
IMAGE_SIZE := 14080k
|
|
DEVICE_PACKAGES := kmod-i2c-gpio kmod-usb2
|
|
LOADER_FLASH_OFFS := 0x20000
|
|
KERNEL := kernel-bin | append-dtb | lzma | uImage lzma -M 0x4f4b4c49
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := $$(IMAGE/sysupgrade.bin) | pisen_wmb001n-factory $(1)
|
|
endef
|
|
TARGET_DEVICES += pisen_wmb001n
|
|
|
|
define Device/pisen_wmm003n
|
|
$(Device/tplink-8mlzma)
|
|
SOC := ar9331
|
|
DEVICE_VENDOR := PISEN
|
|
DEVICE_MODEL := Cloud Easy Power (WMM003N)
|
|
DEVICE_PACKAGES := kmod-usb-chipidea2
|
|
TPLINK_HWID := 0x07030101
|
|
endef
|
|
TARGET_DEVICES += pisen_wmm003n
|
|
|
|
define Device/plasmacloud_pa300-common
|
|
SOC := qca9533
|
|
DEVICE_VENDOR := Plasma Cloud
|
|
DEVICE_PACKAGES := uboot-envtools
|
|
IMAGE_SIZE := 7168k
|
|
IMAGES += factory.bin
|
|
KERNEL := kernel-bin | append-dtb | lzma | uImage lzma | pad-to $$(BLOCKSIZE)
|
|
IMAGE/factory.bin := append-rootfs | pad-rootfs | openmesh-image ce_type=PA300
|
|
IMAGE/sysupgrade.bin := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata
|
|
endef
|
|
|
|
define Device/plasmacloud_pa300
|
|
$(Device/plasmacloud_pa300-common)
|
|
DEVICE_MODEL := PA300
|
|
endef
|
|
TARGET_DEVICES += plasmacloud_pa300
|
|
|
|
define Device/plasmacloud_pa300e
|
|
$(Device/plasmacloud_pa300-common)
|
|
DEVICE_MODEL := PA300E
|
|
endef
|
|
TARGET_DEVICES += plasmacloud_pa300e
|
|
|
|
define Device/qca_ap143
|
|
$(Device/loader-okli-uimage)
|
|
SOC := qca9533
|
|
DEVICE_VENDOR := Qualcomm Atheros
|
|
DEVICE_MODEL := AP143
|
|
DEVICE_PACKAGES := kmod-usb2
|
|
SUPPORTED_DEVICES += ap143
|
|
LOADER_FLASH_OFFS := 0x50000
|
|
KERNEL := kernel-bin | append-dtb | lzma | uImage lzma -M 0x4f4b4c49
|
|
endef
|
|
|
|
define Device/qca_ap143-8m
|
|
$(Device/qca_ap143)
|
|
DEVICE_VARIANT := (8M)
|
|
IMAGE_SIZE := 7744k
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
|
append-rootfs | pad-rootfs | check-size | pad-to 6336k | \
|
|
append-loader-okli-uimage $(1) | pad-to 64k
|
|
endef
|
|
TARGET_DEVICES += qca_ap143-8m
|
|
|
|
define Device/qca_ap143-16m
|
|
$(Device/qca_ap143)
|
|
DEVICE_VARIANT := (16M)
|
|
IMAGE_SIZE := 15936k
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
|
append-rootfs | pad-rootfs | check-size | pad-to 14528k | \
|
|
append-loader-okli-uimage $(1) | pad-to 64k
|
|
endef
|
|
TARGET_DEVICES += qca_ap143-16m
|
|
|
|
define Device/qihoo_c301
|
|
$(Device/seama)
|
|
SOC := ar9344
|
|
DEVICE_VENDOR := Qihoo
|
|
DEVICE_MODEL := C301
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca988x-ct \
|
|
uboot-envtools
|
|
IMAGE_SIZE := 15744k
|
|
SEAMA_SIGNATURE := wrgac26_qihoo360_360rg
|
|
SUPPORTED_DEVICES += qihoo-c301
|
|
endef
|
|
TARGET_DEVICES += qihoo_c301
|
|
|
|
define Device/qxwlan_e1700ac-v2
|
|
SOC := qca9563
|
|
DEVICE_VENDOR := Qxwlan
|
|
DEVICE_MODEL := E1700AC
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
SUPPORTED_DEVICES += e1700ac-v2
|
|
endef
|
|
|
|
define Device/qxwlan_e1700ac-v2-16m
|
|
$(Device/qxwlan_e1700ac-v2)
|
|
DEVICE_VARIANT := v2 (16M)
|
|
IMAGE_SIZE := 15936k
|
|
endef
|
|
TARGET_DEVICES += qxwlan_e1700ac-v2-16m
|
|
|
|
define Device/qxwlan_e1700ac-v2-8m
|
|
$(Device/qxwlan_e1700ac-v2)
|
|
DEVICE_VARIANT := v2 (8M)
|
|
IMAGE_SIZE := 7744k
|
|
endef
|
|
TARGET_DEVICES += qxwlan_e1700ac-v2-8m
|
|
|
|
define Device/qxwlan_e558-v2
|
|
SOC := qca9558
|
|
DEVICE_VENDOR := Qxwlan
|
|
DEVICE_MODEL := E558
|
|
DEVICE_PACKAGES := kmod-usb2
|
|
SUPPORTED_DEVICES += e558-v2
|
|
endef
|
|
|
|
define Device/qxwlan_e558-v2-16m
|
|
$(Device/qxwlan_e558-v2)
|
|
DEVICE_VARIANT := v2 (16M)
|
|
IMAGE_SIZE := 15936k
|
|
endef
|
|
TARGET_DEVICES += qxwlan_e558-v2-16m
|
|
|
|
define Device/qxwlan_e558-v2-8m
|
|
$(Device/qxwlan_e558-v2)
|
|
DEVICE_VARIANT := v2 (8M)
|
|
IMAGE_SIZE := 7744k
|
|
endef
|
|
TARGET_DEVICES += qxwlan_e558-v2-8m
|
|
|
|
define Device/qxwlan_e600g-v2
|
|
SOC := qca9531
|
|
DEVICE_VENDOR := Qxwlan
|
|
DEVICE_MODEL := E600G
|
|
DEVICE_PACKAGES := kmod-usb2
|
|
SUPPORTED_DEVICES += e600g-v2
|
|
endef
|
|
|
|
define Device/qxwlan_e600g-v2-16m
|
|
$(Device/qxwlan_e600g-v2)
|
|
DEVICE_VARIANT := v2 (16M)
|
|
IMAGE_SIZE := 15936k
|
|
endef
|
|
TARGET_DEVICES += qxwlan_e600g-v2-16m
|
|
|
|
define Device/qxwlan_e600g-v2-8m
|
|
$(Device/qxwlan_e600g-v2)
|
|
DEVICE_VARIANT := v2 (8M)
|
|
IMAGE_SIZE := 7744k
|
|
endef
|
|
TARGET_DEVICES += qxwlan_e600g-v2-8m
|
|
|
|
define Device/qxwlan_e600gac-v2
|
|
SOC := qca9531
|
|
DEVICE_VENDOR := Qxwlan
|
|
DEVICE_MODEL := E600GAC
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9887-ct
|
|
SUPPORTED_DEVICES += e600gac-v2
|
|
endef
|
|
|
|
define Device/qxwlan_e600gac-v2-16m
|
|
$(Device/qxwlan_e600gac-v2)
|
|
DEVICE_VARIANT := v2 (16M)
|
|
IMAGE_SIZE := 15936k
|
|
endef
|
|
TARGET_DEVICES += qxwlan_e600gac-v2-16m
|
|
|
|
define Device/qxwlan_e600gac-v2-8m
|
|
$(Device/qxwlan_e600gac-v2)
|
|
DEVICE_VARIANT := v2 (8M)
|
|
IMAGE_SIZE := 7744k
|
|
endef
|
|
TARGET_DEVICES += qxwlan_e600gac-v2-8m
|
|
|
|
define Device/qxwlan_e750a-v4
|
|
SOC := ar9344
|
|
DEVICE_VENDOR := Qxwlan
|
|
DEVICE_MODEL := E750A
|
|
DEVICE_PACKAGES := kmod-usb2
|
|
SUPPORTED_DEVICES += e750a-v4
|
|
endef
|
|
|
|
define Device/qxwlan_e750a-v4-16m
|
|
$(Device/qxwlan_e750a-v4)
|
|
DEVICE_VARIANT := v4 (16M)
|
|
IMAGE_SIZE := 15936k
|
|
endef
|
|
TARGET_DEVICES += qxwlan_e750a-v4-16m
|
|
|
|
define Device/qxwlan_e750a-v4-8m
|
|
$(Device/qxwlan_e750a-v4)
|
|
DEVICE_VARIANT := v4 (8M)
|
|
IMAGE_SIZE := 7744k
|
|
endef
|
|
TARGET_DEVICES += qxwlan_e750a-v4-8m
|
|
|
|
define Device/qxwlan_e750g-v8
|
|
SOC := ar9344
|
|
DEVICE_VENDOR := Qxwlan
|
|
DEVICE_MODEL := E750G
|
|
DEVICE_PACKAGES := kmod-usb2
|
|
SUPPORTED_DEVICES += e750g-v8
|
|
endef
|
|
|
|
define Device/qxwlan_e750g-v8-16m
|
|
$(Device/qxwlan_e750g-v8)
|
|
DEVICE_VARIANT := v8 (16M)
|
|
IMAGE_SIZE := 15936k
|
|
endef
|
|
TARGET_DEVICES += qxwlan_e750g-v8-16m
|
|
|
|
define Device/qxwlan_e750g-v8-8m
|
|
$(Device/qxwlan_e750g-v8)
|
|
DEVICE_VARIANT := v8 (8M)
|
|
IMAGE_SIZE := 7744k
|
|
endef
|
|
TARGET_DEVICES += qxwlan_e750g-v8-8m
|
|
|
|
define Device/rosinson_wr818
|
|
SOC := qca9563
|
|
DEVICE_VENDOR := Rosinson
|
|
DEVICE_MODEL := WR818
|
|
IMAGE_SIZE := 15872k
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += rosinson_wr818
|
|
|
|
define Device/ruckus_common
|
|
DEVICE_VENDOR := Ruckus
|
|
LOADER_TYPE := bin
|
|
KERNEL := kernel-bin | append-dtb | lzma | loader-kernel | uImage none
|
|
KERNEL_INITRAMFS := kernel-bin | append-dtb | lzma | loader-kernel | uImage none
|
|
endef
|
|
|
|
define Device/ruckus_zf7025
|
|
$(Device/ruckus_common)
|
|
SOC := ar7240
|
|
DEVICE_MODEL := ZoneFlex 7025
|
|
IMAGE_SIZE := 15616k
|
|
BLOCKSIZE := 256k
|
|
endef
|
|
TARGET_DEVICES += ruckus_zf7025
|
|
|
|
define Device/ruckus_zf73xx_common
|
|
$(Device/ruckus_common)
|
|
DEVICE_PACKAGES := -swconfig kmod-usb2 kmod-usb-chipidea2
|
|
IMAGE_SIZE := 31744k
|
|
endef
|
|
|
|
define Device/ruckus_zf7321
|
|
$(Device/ruckus_zf73xx_common)
|
|
SOC := ar9342
|
|
DEVICE_MODEL := ZoneFlex 7321[-U]
|
|
endef
|
|
TARGET_DEVICES += ruckus_zf7321
|
|
|
|
define Device/ruckus_zf7372
|
|
$(Device/ruckus_zf73xx_common)
|
|
SOC := ar9344
|
|
DEVICE_MODEL := ZoneFlex 7352/7372[-E/-U]
|
|
endef
|
|
TARGET_DEVICES += ruckus_zf7372
|
|
|
|
define Device/samsung_wam250
|
|
SOC := ar9344
|
|
DEVICE_VENDOR := Samsung
|
|
DEVICE_MODEL := WAM250
|
|
IMAGE_SIZE := 15872k
|
|
DEVICE_PACKAGES := kmod-usb2
|
|
SUPPORTED_DEVICES += wam250
|
|
endef
|
|
TARGET_DEVICES += samsung_wam250
|
|
|
|
define Device/siemens_ws-ap3610
|
|
SOC := ar7161
|
|
DEVICE_VENDOR := Siemens
|
|
DEVICE_MODEL := WS-AP3610
|
|
IMAGE_SIZE := 14336k
|
|
BLOCKSIZE := 256k
|
|
LOADER_TYPE := bin
|
|
LOADER_FLASH_OFFS := 0x82000
|
|
COMPILE := loader-$(1).bin
|
|
COMPILE/loader-$(1).bin := loader-okli-compile
|
|
KERNEL := kernel-bin | append-dtb | lzma | uImage lzma -M 0x4f4b4c49 | loader-okli $(1) 8128 | uImage none
|
|
KERNEL_INITRAMFS := kernel-bin | append-dtb | uImage none
|
|
endef
|
|
TARGET_DEVICES += siemens_ws-ap3610
|
|
|
|
define Device/sitecom_wlr-7100
|
|
SOC := ar1022
|
|
DEVICE_VENDOR := Sitecom
|
|
DEVICE_MODEL := WLR-7100
|
|
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct-smallbuffers kmod-usb2
|
|
IMAGES += factory.dlf
|
|
IMAGE/factory.dlf := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
|
append-rootfs | pad-rootfs | check-size | \
|
|
senao-header -r 0x222 -p 0x53 -t 2
|
|
IMAGE_SIZE := 7488k
|
|
endef
|
|
TARGET_DEVICES += sitecom_wlr-7100
|
|
|
|
define Device/sitecom_wlr-8100
|
|
SOC := qca9558
|
|
DEVICE_VENDOR := Sitecom
|
|
DEVICE_MODEL := WLR-8100
|
|
DEVICE_ALT0_VENDOR := Sitecom
|
|
DEVICE_ALT0_MODEL := X8 AC1750
|
|
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct kmod-usb2 kmod-usb3
|
|
SUPPORTED_DEVICES += wlr8100
|
|
IMAGES += factory.dlf
|
|
IMAGE/factory.dlf := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
|
append-rootfs | pad-rootfs | check-size | \
|
|
senao-header -r 0x222 -p 0x56 -t 2
|
|
IMAGE_SIZE := 15424k
|
|
endef
|
|
TARGET_DEVICES += sitecom_wlr-8100
|
|
|
|
define Device/sophos_ap15
|
|
SOC := qca9558
|
|
DEVICE_VENDOR := Sophos
|
|
DEVICE_MODEL := AP15
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
IMAGE_SIZE := 15936k
|
|
endef
|
|
TARGET_DEVICES += sophos_ap15
|
|
|
|
define Device/sophos_ap55
|
|
SOC := qca9558
|
|
DEVICE_VENDOR := Sophos
|
|
DEVICE_MODEL := AP55
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct kmod-usb2
|
|
IMAGE_SIZE := 15936k
|
|
endef
|
|
TARGET_DEVICES += sophos_ap55
|
|
|
|
define Device/sophos_ap55c
|
|
SOC := qca9558
|
|
DEVICE_VENDOR := Sophos
|
|
DEVICE_MODEL := AP55C
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
IMAGE_SIZE := 15936k
|
|
endef
|
|
TARGET_DEVICES += sophos_ap55c
|
|
|
|
define Device/sophos_ap100
|
|
SOC := qca9558
|
|
DEVICE_VENDOR := Sophos
|
|
DEVICE_MODEL := AP100
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct kmod-usb2
|
|
IMAGE_SIZE := 15936k
|
|
endef
|
|
TARGET_DEVICES += sophos_ap100
|
|
|
|
define Device/sophos_ap100c
|
|
SOC := qca9558
|
|
DEVICE_VENDOR := Sophos
|
|
DEVICE_MODEL := AP100C
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
IMAGE_SIZE := 15936k
|
|
endef
|
|
TARGET_DEVICES += sophos_ap100c
|
|
|
|
define Device/telco_t1
|
|
SOC := qca9531
|
|
DEVICE_VENDOR := Telco
|
|
DEVICE_MODEL := T1
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-usb-net-qmi-wwan \
|
|
kmod-usb-serial-option uqmi -swconfig -uboot-envtools
|
|
IMAGE_SIZE := 16192k
|
|
SUPPORTED_DEVICES += telco_electronics,tel-t1
|
|
endef
|
|
TARGET_DEVICES += telco_t1
|
|
|
|
define Device/teltonika_rut230-v1
|
|
SOC := ar9331
|
|
DEVICE_VENDOR := Teltonika
|
|
DEVICE_MODEL := RUT230
|
|
DEVICE_VARIANT := v1
|
|
DEVICE_PACKAGES := kmod-usb-chipidea2 kmod-usb-acm kmod-usb-net-qmi-wwan \
|
|
uqmi -uboot-envtools
|
|
IMAGE_SIZE := 15552k
|
|
TPLINK_HWID := 0x32200002
|
|
TPLINK_HWREV := 0x1
|
|
TPLINK_HEADER_VERSION := 1
|
|
KERNEL := kernel-bin | append-dtb | lzma | teltonika-v1-header
|
|
KERNEL_INITRAMFS := kernel-bin | append-dtb | lzma | uImage lzma
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs |\
|
|
pad-rootfs | pad-extra 64 | teltonika-fw-fake-checksum 54 | check-size
|
|
IMAGE/sysupgrade.bin := append-kernel | pad-to $$$$(BLOCKSIZE) |\
|
|
append-rootfs | pad-rootfs | append-metadata |\
|
|
check-size
|
|
endef
|
|
TARGET_DEVICES += teltonika_rut230-v1
|
|
|
|
define Device/teltonika_rut300
|
|
SOC := qca9531
|
|
DEVICE_VENDOR := Teltonika
|
|
DEVICE_MODEL := RUT300
|
|
SUPPORTED_TELTONIKA_DEVICES := teltonika,rut30x
|
|
DEVICE_PACKAGES := -kmod-ath9k -uboot-envtools -wpad-basic-mbedtls kmod-usb2
|
|
IMAGE_SIZE := 15552k
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin = append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
|
append-rootfs | pad-rootfs | append-metadata-teltonika | \
|
|
check-size $$$$(IMAGE_SIZE)
|
|
IMAGE/sysupgrade.bin = append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
|
append-rootfs | pad-rootfs | append-metadata | \
|
|
check-size $$$$(IMAGE_SIZE)
|
|
endef
|
|
TARGET_DEVICES += teltonika_rut300
|
|
|
|
define Device/teltonika_rut955
|
|
SOC := ar9344
|
|
DEVICE_VENDOR := Teltonika
|
|
DEVICE_MODEL := RUT955
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-usb-acm kmod-usb-net-qmi-wwan \
|
|
kmod-usb-serial-option kmod-hwmon-mcp3021 uqmi -uboot-envtools
|
|
IMAGE_SIZE := 15552k
|
|
TPLINK_HWID := 0x35000001
|
|
TPLINK_HWREV := 0x1
|
|
TPLINK_HEADER_VERSION := 1
|
|
KERNEL := kernel-bin | append-dtb | lzma | tplink-v1-header
|
|
KERNEL_INITRAMFS := kernel-bin | append-dtb | lzma | uImage lzma
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs |\
|
|
pad-rootfs | teltonika-fw-fake-checksum 20 | append-string master |\
|
|
append-md5sum-bin | check-size
|
|
IMAGE/sysupgrade.bin := append-kernel | pad-to $$$$(BLOCKSIZE) |\
|
|
append-rootfs | pad-rootfs | check-size | append-metadata
|
|
endef
|
|
TARGET_DEVICES += teltonika_rut955
|
|
|
|
define Device/teltonika_rut955-h7v3c0
|
|
$(Device/teltonika_rut955)
|
|
DEVICE_VARIANT := H7V3C0
|
|
endef
|
|
TARGET_DEVICES += teltonika_rut955-h7v3c0
|
|
|
|
define Device/trendnet_tew-673gru
|
|
SOC := ar7161
|
|
DEVICE_VENDOR := Trendnet
|
|
DEVICE_MODEL := TEW-673GRU
|
|
DEVICE_VARIANT := v1.0R
|
|
DEVICE_PACKAGES := -uboot-envtools kmod-usb-ohci kmod-usb2 \
|
|
kmod-owl-loader kmod-switch-rtl8366s
|
|
IMAGE_SIZE := 7808k
|
|
FACTORY_SIZE := 6144k
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin = append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | \
|
|
pad-rootfs | check-size $$$$(FACTORY_SIZE) | pad-to $$$$(FACTORY_SIZE) | \
|
|
append-string AP94-AR7161-RT-080619-01
|
|
endef
|
|
TARGET_DEVICES += trendnet_tew-673gru
|
|
|
|
define Device/trendnet_tew-823dru
|
|
SOC := qca9558
|
|
DEVICE_VENDOR := Trendnet
|
|
DEVICE_MODEL := TEW-823DRU
|
|
DEVICE_VARIANT := v1.0R
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
SUPPORTED_DEVICES += tew-823dru
|
|
IMAGE_SIZE := 15296k
|
|
IMAGES := factory.bin sysupgrade.bin
|
|
IMAGE/default := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | \
|
|
pad-rootfs
|
|
IMAGE/factory.bin := $$(IMAGE/default) | pad-offset $$$$(IMAGE_SIZE) 26 | \
|
|
append-string 00AP135AR9558-RT-131129-00 | check-size
|
|
IMAGE/sysupgrade.bin := $$(IMAGE/default) | check-size | append-metadata
|
|
endef
|
|
TARGET_DEVICES += trendnet_tew-823dru
|
|
|
|
define Device/wallys_dr531
|
|
SOC := qca9531
|
|
DEVICE_VENDOR := Wallys
|
|
DEVICE_MODEL := DR531
|
|
DEVICE_PACKAGES := kmod-usb2 rssileds
|
|
IMAGE_SIZE := 7808k
|
|
SUPPORTED_DEVICES += dr531
|
|
endef
|
|
TARGET_DEVICES += wallys_dr531
|
|
|
|
define Device/watchguard_ap100
|
|
$(Device/senao_loader_okli)
|
|
SOC := ar9344
|
|
DEVICE_VENDOR := WatchGuard
|
|
DEVICE_MODEL := AP100
|
|
IMAGE_SIZE := 12096k
|
|
LOADER_FLASH_OFFS := 0x220000
|
|
SENAO_IMGNAME := senao-ap100
|
|
WATCHGUARD_MAGIC := 82kdlzk2
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | \
|
|
check-size | senao-tar-gz $$$$(SENAO_IMGNAME) | watchguard-cksum $$$$(WATCHGUARD_MAGIC)
|
|
endef
|
|
TARGET_DEVICES += watchguard_ap100
|
|
|
|
define Device/watchguard_ap200
|
|
$(Device/senao_loader_okli)
|
|
SOC := ar9344
|
|
DEVICE_VENDOR := WatchGuard
|
|
DEVICE_MODEL := AP200
|
|
IMAGE_SIZE := 12096k
|
|
LOADER_FLASH_OFFS := 0x220000
|
|
SENAO_IMGNAME := senao-ap200
|
|
WATCHGUARD_MAGIC := 82kdlzk2
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | \
|
|
check-size | senao-tar-gz $$$$(SENAO_IMGNAME) | watchguard-cksum $$$$(WATCHGUARD_MAGIC)
|
|
endef
|
|
TARGET_DEVICES += watchguard_ap200
|
|
|
|
define Device/watchguard_ap300
|
|
$(Device/senao_loader_okli)
|
|
SOC := qca9558
|
|
DEVICE_VENDOR := WatchGuard
|
|
DEVICE_MODEL := AP300
|
|
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct
|
|
IMAGE_SIZE := 11584k
|
|
LOADER_FLASH_OFFS := 0x220000
|
|
SENAO_IMGNAME := senao-ap300
|
|
WATCHGUARD_MAGIC := 82kdlzk2
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | \
|
|
check-size | senao-tar-gz $$$$(SENAO_IMGNAME) | watchguard-cksum $$$$(WATCHGUARD_MAGIC)
|
|
endef
|
|
TARGET_DEVICES += watchguard_ap300
|
|
|
|
define Device/wd_mynet-n600
|
|
$(Device/seama)
|
|
SOC := ar9344
|
|
DEVICE_VENDOR := Western Digital
|
|
DEVICE_MODEL := My Net N600
|
|
IMAGE_SIZE := 15872k
|
|
DEVICE_PACKAGES := kmod-usb2
|
|
SEAMA_SIGNATURE := wrgnd16_wd_db600
|
|
SUPPORTED_DEVICES += mynet-n600
|
|
endef
|
|
TARGET_DEVICES += wd_mynet-n600
|
|
|
|
define Device/wd_mynet-n750
|
|
$(Device/seama)
|
|
SOC := ar9344
|
|
DEVICE_VENDOR := Western Digital
|
|
DEVICE_MODEL := My Net N750
|
|
IMAGE_SIZE := 15872k
|
|
DEVICE_PACKAGES := kmod-usb2
|
|
SEAMA_SIGNATURE := wrgnd13_wd_av
|
|
SUPPORTED_DEVICES += mynet-n750
|
|
endef
|
|
TARGET_DEVICES += wd_mynet-n750
|
|
|
|
define Device/wd_mynet-wifi-rangeextender
|
|
SOC := ar9344
|
|
DEVICE_VENDOR := Western Digital
|
|
DEVICE_MODEL := My Net Wi-Fi Range Extender
|
|
DEVICE_PACKAGES := rssileds nvram -swconfig
|
|
IMAGE_SIZE := 7808k
|
|
ADDPATTERN_ID := mynet-rext
|
|
ADDPATTERN_VERSION := 1.00.01
|
|
IMAGE/sysupgrade.bin := append-rootfs | pad-rootfs | cybertan-trx | \
|
|
addpattern | append-metadata
|
|
SUPPORTED_DEVICES += mynet-rext
|
|
endef
|
|
TARGET_DEVICES += wd_mynet-wifi-rangeextender
|
|
|
|
define Device/winchannel_wb2000
|
|
SOC := ar9344
|
|
DEVICE_VENDOR := Winchannel
|
|
DEVICE_MODEL := WB2000
|
|
IMAGE_SIZE := 15872k
|
|
DEVICE_PACKAGES := kmod-i2c-gpio kmod-rtc-ds1307 kmod-usb2 \
|
|
kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += winchannel_wb2000
|
|
|
|
define Device/xiaomi_aiot-ac2350
|
|
SOC := qca9563
|
|
DEVICE_VENDOR := Xiaomi
|
|
DEVICE_MODEL := AIoT AC2350
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9984-ct
|
|
IMAGE_SIZE := 14336k
|
|
endef
|
|
TARGET_DEVICES += xiaomi_aiot-ac2350
|
|
|
|
define Device/xiaomi_mi-router-4q
|
|
SOC := qca9561
|
|
DEVICE_VENDOR := Xiaomi
|
|
DEVICE_MODEL := Mi Router 4Q
|
|
IMAGE_SIZE := 14336k
|
|
endef
|
|
TARGET_DEVICES += xiaomi_mi-router-4q
|
|
|
|
define Device/yuncore_a770
|
|
SOC := qca9531
|
|
DEVICE_VENDOR := YunCore
|
|
DEVICE_MODEL := A770
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9887-ct
|
|
IMAGE_SIZE := 16000k
|
|
IMAGES += tftp.bin
|
|
IMAGE/tftp.bin := $$(IMAGE/sysupgrade.bin) | yuncore-tftp-header-16m
|
|
endef
|
|
TARGET_DEVICES += yuncore_a770
|
|
|
|
define Device/yuncore_a782
|
|
SOC := qca9563
|
|
DEVICE_VENDOR := YunCore
|
|
DEVICE_MODEL := A782
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct
|
|
IMAGE_SIZE := 16000k
|
|
IMAGES += tftp.bin
|
|
IMAGE/tftp.bin := $$(IMAGE/sysupgrade.bin) | yuncore-tftp-header-16m
|
|
endef
|
|
TARGET_DEVICES += yuncore_a782
|
|
|
|
define Device/yuncore_a930
|
|
SOC := qca9533
|
|
DEVICE_VENDOR := YunCore
|
|
DEVICE_MODEL := A930
|
|
IMAGE_SIZE := 16000k
|
|
IMAGES += tftp.bin
|
|
IMAGE/tftp.bin := $$(IMAGE/sysupgrade.bin) | yuncore-tftp-header-16m
|
|
endef
|
|
TARGET_DEVICES += yuncore_a930
|
|
|
|
define Device/yuncore_xd3200
|
|
SOC := qca9563
|
|
DEVICE_VENDOR := YunCore
|
|
DEVICE_MODEL := XD3200
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
IMAGE_SIZE := 16000k
|
|
IMAGES += tftp.bin
|
|
IMAGE/tftp.bin := $$(IMAGE/sysupgrade.bin) | yuncore-tftp-header-16m
|
|
endef
|
|
TARGET_DEVICES += yuncore_xd3200
|
|
|
|
define Device/yuncore_xd4200
|
|
SOC := qca9563
|
|
DEVICE_VENDOR := YunCore
|
|
DEVICE_MODEL := XD4200
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct
|
|
IMAGE_SIZE := 16000k
|
|
IMAGES += tftp.bin
|
|
IMAGE/tftp.bin := $$(IMAGE/sysupgrade.bin) | yuncore-tftp-header-16m
|
|
endef
|
|
TARGET_DEVICES += yuncore_xd4200
|
|
|
|
define Device/ziking_cpe46b
|
|
SOC := ar9330
|
|
DEVICE_VENDOR := ZiKing
|
|
DEVICE_MODEL := CPE46B
|
|
IMAGE_SIZE := 8000k
|
|
DEVICE_PACKAGES := kmod-i2c-gpio
|
|
endef
|
|
TARGET_DEVICES += ziking_cpe46b
|
|
|
|
define Device/zbtlink_zbt-wd323
|
|
SOC := ar9344
|
|
DEVICE_VENDOR := ZBT
|
|
DEVICE_MODEL := WD323
|
|
IMAGE_SIZE := 16000k
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-i2c-gpio kmod-rtc-pcf8563 \
|
|
kmod-usb-serial-cp210x uqmi
|
|
endef
|
|
TARGET_DEVICES += zbtlink_zbt-wd323
|
|
|
|
define Device/zyxel_nwa11xx
|
|
$(Device/loader-okli-uimage)
|
|
SOC := ar9342
|
|
DEVICE_VENDOR := ZyXEL
|
|
LOADER_FLASH_OFFS := 0x050000
|
|
KERNEL := kernel-bin | append-dtb | lzma | uImage lzma -M 0x4f4b4c49
|
|
IMAGE_SIZE := 8192k
|
|
IMAGES += factory-$$$$(ZYXEL_MODEL_STRING).bin
|
|
IMAGE/factory-$$$$(ZYXEL_MODEL_STRING).bin := \
|
|
append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | \
|
|
pad-rootfs | pad-to 8192k | check-size | zyxel-tar-bz2 \
|
|
vmlinux_mi124_f1e mi124_f1e-jffs2 | append-md5sum-bin
|
|
endef
|
|
|
|
define Device/zyxel_nwa1100-nh
|
|
$(Device/zyxel_nwa11xx)
|
|
DEVICE_MODEL := NWA1100
|
|
DEVICE_VARIANT := NH
|
|
ZYXEL_MODEL_STRING := AASI
|
|
endef
|
|
TARGET_DEVICES += zyxel_nwa1100-nh
|
|
|
|
define Device/zyxel_nwa1121-ni
|
|
$(Device/zyxel_nwa11xx)
|
|
DEVICE_MODEL := NWA1121
|
|
DEVICE_VARIANT := NI
|
|
ZYXEL_MODEL_STRING := AABJ
|
|
endef
|
|
TARGET_DEVICES += zyxel_nwa1121-ni
|
|
|
|
define Device/zyxel_nwa1123-ac
|
|
$(Device/zyxel_nwa11xx)
|
|
DEVICE_MODEL := NWA1123
|
|
DEVICE_VARIANT := AC
|
|
ZYXEL_MODEL_STRING := AAOX
|
|
DEVICE_PACKAGES := kmod-ath10k-ct-smallbuffers \
|
|
ath10k-firmware-qca988x-ct
|
|
endef
|
|
TARGET_DEVICES += zyxel_nwa1123-ac
|
|
|
|
define Device/zyxel_nwa1123-ni
|
|
$(Device/zyxel_nwa11xx)
|
|
DEVICE_MODEL := NWA1123
|
|
DEVICE_VARIANT := NI
|
|
ZYXEL_MODEL_STRING := AAEO
|
|
endef
|
|
TARGET_DEVICES += zyxel_nwa1123-ni
|
|
|
|
define Device/zyxel_nbg6616
|
|
SOC := qca9557
|
|
DEVICE_VENDOR := ZyXEL
|
|
DEVICE_MODEL := NBG6616
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport kmod-rtc-pcf8563 \
|
|
kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
IMAGE_SIZE := 15232k
|
|
RAS_BOARD := NBG6616
|
|
RAS_ROOTFS_SIZE := 14464k
|
|
RAS_VERSION := "OpenWrt Linux-$(LINUX_VERSION)"
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
|
append-rootfs | pad-rootfs | pad-to 64k | check-size | zyxel-ras-image
|
|
SUPPORTED_DEVICES += nbg6616
|
|
endef
|
|
TARGET_DEVICES += zyxel_nbg6616
|