mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-29 01:59:02 +00:00
0b20490207
* QCA IPQ4019
* 256 MB of RAM
* 32 MB of SPI NOR flash (s25fl256s1)
- 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=OM-A62
* 2T2R 5 GHz (channel 36-64)
- QCA9888 hw2.0 (PCI)
- requires special BDF in QCA9888/hw2.0/board-2.bin
bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=OM-A62
* 2T2R 5 GHz (channel 100-165)
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=OM-A62
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x button (reset; kmod-input-gpio-keys compatible)
* external watchdog
- triggered GPIO
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
- phy@mdio3:
+ Label: Ethernet 1
+ gmac0 (ethaddr) in original firmware
+ 802.3at POE+
- phy@mdio4:
+ Label: Ethernet 2
+ gmac1 (eth1addr) in original firmware
+ 18-24V passive POE (mode B)
* powered only via POE
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.
The initramfs image can be started using
setenv bootargs 'loglevel=8 earlycon=msm_serial_dm,0x78af000 console=ttyMSM0,115200 mtdparts=spi0.0:256k(0:SBL1),128k(0:MIBIB),384k(0:QSEE),64k(0:CDT),64k(0:DDRPARAMS),64k(0:APPSBLENV),512k(0:APPSBL),64k(0:ART),64k(0:custom),64k(0:KEYS),15552k(inactive),15552k(inactive2)'
tftpboot 0x84000000 openwrt-ipq40xx-openmesh_a62-initramfs-fit-uImage.itb
set fdt_high 0x85000000
bootm 0x84000000
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
44 lines
922 B
Bash
44 lines
922 B
Bash
#!/bin/sh
|
|
#
|
|
# Copyright (C) 2016 LEDE
|
|
#
|
|
|
|
[ -e /etc/config/ubootenv ] && exit 0
|
|
|
|
touch /etc/config/ubootenv
|
|
|
|
. /lib/uboot-envtools.sh
|
|
. /lib/functions.sh
|
|
|
|
board=$(board_name)
|
|
|
|
ubootenv_mtdinfo () {
|
|
UBOOTENV_PART=$(cat /proc/mtd | grep APPSBLENV)
|
|
mtd_dev=$(echo $UBOOTENV_PART | awk '{print $1}' | sed 's/:$//')
|
|
mtd_size=$(echo $UBOOTENV_PART | awk '{print "0x"$2}')
|
|
mtd_erase=$(echo $UBOOTENV_PART | awk '{print "0x"$3}')
|
|
nor_flash=$(find /sys/bus/spi/devices/*/mtd -name ${mtd_dev})
|
|
|
|
if [ -n "$nor_flash" ]; then
|
|
ubootenv_size=$mtd_size
|
|
else
|
|
# size is fixed to 0x40000 in u-boot
|
|
ubootenv_size=0x40000
|
|
fi
|
|
|
|
sectors=$(( $ubootenv_size / $mtd_erase ))
|
|
echo /dev/$mtd_dev 0x0 $ubootenv_size $mtd_erase $sectors
|
|
}
|
|
|
|
case "$board" in
|
|
openmesh,a42 |\
|
|
openmesh,a62)
|
|
ubootenv_add_uci_config "/dev/mtd5" "0x0" "0x10000" "0x10000"
|
|
;;
|
|
esac
|
|
|
|
config_load ubootenv
|
|
config_foreach ubootenv_add_app_config ubootenv
|
|
|
|
exit 0
|