ExternalVendorCode/openwrt
1
0
Fork 0
mirror of https://github.com/openwrt/openwrt.git synced 2024-12-22 23:12:32 +00:00
Code Issues Actions 6 Packages Projects Releases Wiki Activity
f70ee53b08
openwrt/target/linux/ipq40xx/image/generic.mk
Andreas Böhler f70ee53b08 ipq4019: add support for ZTE MF287+ aka DreiNeo 
The ZTE MF287+ is a LTE router used (exclusively?) by the network operator
"3". The MF287 (i.e. non-plus aka 3Neo) is also supported (the only
difference is the LTE modem)

Specifications
==============

SoC: IPQ4018
RAM: 256MiB
Flash: 8MiB SPI-NOR + 128MiB SPI-NAND
LAN: 4x GBit LAN
LTE: ZTE Cat12 (MF287+) / ZTE Cat6 (MF287)
WiFi: 802.11a/b/g/n/ac SoC-integrated

MAC addresses
=============

LAN: from config + 2
WiFi 1: from config
WiFi 2: from config + 1

Installation
============

Option 1 - TFTP
---------------

TFTP installation using UART is preferred. Disassemble the device and
connect serial. Put the initramfs image as openwrt.bin to your TFTP server
and configure a static IP of 192.168.1.100. Load the initramfs image by
typing:

  setenv serverip 192.168.1.100
  setenv ipaddr 192.168.1.1
  tftpboot 0x82000000 openwrt.bin
  bootm 0x82000000

From this intiramfs boot you can take a backup of the currently installed
partitions as no vendor firmware is available for download:

  ubiattach -m14
  cat /dev/ubi0_0 > /tmp/ubi0_0
  cat /dev/ubi0_1 > /tmp/ubi0_1

Copy the files /tmp/ubi0_0 and /tmp/ubi0_1 somewhere save.

Once booted, transfer the sysupgrade image and run sysupgrade. You might
have to delete the stock volumes first:

  ubirmvol /dev/ubi0 -N ubi_rootfs
  ubirmvol /dev/ubi0 -N kernel

Option 2 - From stock firmware
------------------------------

The installation from stock requires an exploit first. The exploit consists
of a backup file that forces the firmware to download telnetd via TFTP from
192.168.0.22 and run it. Once exploited, you can connect via telnet and
login as admin:admin.

The exploit will be available at the device wiki page.

Once inside the stock firmware, you can transfer the -factory.bin file to
/tmp by using "scp" from the stock frmware or "tftp".

ZTE has blocked writing to the NAND. Fortunately, it's easy to allow write
access - you need to read from one file in /proc. Once done, you need to
erase the UBI partition and flash OpenWrt. Before performing the operation,
make sure that mtd13 is the partition labelled "rootfs" by calling
"cat /proc/mtd".

Complete commands:

  cd /tmp
  tftp -g -r factory.bin 192.168.0.22
  cat /proc/driver/sensor_id
  flash_erase /dev/mtd13 0 0
  dd if=/tmp/factory.bin of=/dev/mtdblock13 bs=131072

Afterwards, reboot your device and you should have a working OpenWrt
installation.

Restore Stock
=============

Option 1 - via UART
-------------------

Boot an OpenWrt initramfs image via TFTP as for the initial installation.
Transfer the two backed-up files to your box to /tmp.

Then, run the following commands - replace $kernel_length and $rootfs_size
by the size of ubi0_0 and ubi0_1 in bytes.

  ubiattach -m 14
  ubirmvol /dev/ubi0 -N kernel
  ubirmvol /dev/ubi0 -N rootfs
  ubirmvol /dev/ubi0 -N rootfs_data
  ubimkvol /dev/ubi0 -N kernel -s $kernel_length
  ubimkvol /dev/ubi0 -N ubi_rootfs -s $rootfs_size
  ubiupdatevol /dev/ubi0_0 /tmp/ubi0_0
  ubiupdatevol /dev/ubi0_1 /tmp/ubi0_1

Option 2 - from within OpenWrt
------------------------------

This option requires to flash an initramfs version first so that access
to the flash is possible. This can be achieved by sysupgrading to the
recovery.bin version and rebooting. Once rebooted, you are again in a
default OpenWrt installation, but no partition is mounted.

Follow the commands from Option 1 to flash back to stock.

LTE Modem
=========

The LTE modem is similar to other ZTE devices and controls some more LEDs
and battery management.

Configuring the connection using uqmi works properly, the modem
provides three serial ports and a QMI CDC ethernet interface.

Signed-off-by: Andreas Böhler <dev@aboehler.at>
2023-06-25 15:53:03 +02:00

1210 lines
35 KiB
Makefile
Raw Blame History

DEVICE_VARS += NETGEAR_BOARD_ID NETGEAR_HW_ID
DEVICE_VARS += RAS_BOARD RAS_ROOTFS_SIZE RAS_VERSION
DEVICE_VARS += WRGG_DEVNAME WRGG_SIGNATURE
define Device/FitImage
KERNEL_SUFFIX := -uImage.itb
KERNEL = kernel-bin | gzip | fit gzip $$(KDIR)/image-$$(DEVICE_DTS).dtb
KERNEL_NAME := Image
endef
define Device/FitImageLzma
KERNEL_SUFFIX := -uImage.itb
KERNEL = kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(DEVICE_DTS).dtb
KERNEL_NAME := Image
endef
define Device/FitzImage
KERNEL_SUFFIX := -zImage.itb
KERNEL = kernel-bin | fit none $$(KDIR)/image-$$(DEVICE_DTS).dtb
KERNEL_NAME := zImage
endef
define Device/UbiFit
KERNEL_IN_UBI := 1
IMAGES := factory.ubi sysupgrade.bin
IMAGE/factory.ubi := append-ubi
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
endef
define Device/DniImage
$(call Device/FitzImage)
NETGEAR_BOARD_ID :=
NETGEAR_HW_ID :=
IMAGES += factory.img
IMAGE/factory.img := append-kernel | pad-offset 64k 64 | append-uImage-fakehdr filesystem | append-rootfs | pad-rootfs | netgear-dni
IMAGE/sysupgrade.bin := append-kernel | pad-offset 64k 64 | append-uImage-fakehdr filesystem | \
append-rootfs | pad-rootfs | check-size | append-metadata
endef
define Build/append-rootfshdr
mkimage -A $(LINUX_KARCH) \
-O linux -T filesystem \
-C lzma -a $(KERNEL_LOADADDR) -e $(if $(KERNEL_ENTRY),$(KERNEL_ENTRY),$(KERNEL_LOADADDR)) \
-n root.squashfs -d $(IMAGE_ROOTFS) $@.new
cat $(IMAGE_KERNEL) > $@.$1
dd if=$@.new bs=64 count=1 >> $@.$1
endef
define Build/append-rutx-metadata
echo \
'{ \
"device_code": [".*"], \
"hwver": [".*"], \
"batch": [".*"], \
"serial": [".*"], \
"supported_devices":["teltonika,rutx"] \
}' | fwtool -I - $@
endef
define Build/copy-file
cat "$(1)" > "$@"
endef
define Build/mkmylofw_32m
$(eval device_id=$(word 1,$(1)))
$(eval revision=$(word 2,$(1)))
let \
size="$$(stat -c%s $@)" \
pad="$(subst k,* 1024,$(BLOCKSIZE))" \
pad="(pad - (size % pad)) % pad" \
newsize='size + pad'; \
$(STAGING_DIR_HOST)/bin/mkmylofw \
-B WPE72 -i 0x11f6:$(device_id):0x11f6:$(device_id) -r $(revision) \
-s 0x2000000 -p0x180000:$$newsize:al:0x80208000:"OpenWrt":$@ \
$@.new
@mv $@.new $@
endef
define Build/wac5xx-netgear-tar
mkdir $@.tmp
mv $@ $@.tmp/wac5xx-ubifs-root.img
md5sum $@.tmp/wac5xx-ubifs-root.img > $@.tmp/wac5xx-ubifs-root.md5sum
echo "WAC505 WAC510" > $@.tmp/metadata.txt
echo "WAC505_V9.9.9.9" > $@.tmp/version
tar -C $@.tmp/ -cf $@ .
rm -rf $@.tmp
endef
define Build/qsdk-ipq-factory-nand-askey
$(TOPDIR)/scripts/mkits-qsdk-ipq-image.sh $@.its\
askey_kernel $@.$1 \
askey_fs $(IMAGE_ROOTFS) \
ubifs $@
PATH=$(LINUX_DIR)/scripts/dtc:$(PATH) mkimage -f $@.its $@.new
@mv $@.new $@
endef
define Build/qsdk-ipq-app-gpt
cp $@ $@.tmp 2>/dev/null || true
ptgen -g -o $@.tmp -a 1 -l 1024 \
-t 0x2e -N 0:HLOS -r -p 32M \
-t 0x83 -N rootfs -r -p 128M \
-N rootfs_data -p 512M
cat $@.tmp >> $@
rm $@.tmp
endef
define Build/SenaoFW
-$(STAGING_DIR_HOST)/bin/mksenaofw \
-n $(BOARD_NAME) -r $(VENDOR_ID) -p $(1) \
-c $(DATECODE) -w $(2) -x $(CW_VER) -t 0 \
-e $@ \
-o $@.new
@cp $@.new $@
endef
define Build/wrgg-image
mkwrggimg -i $@ \
-o $@.new \
-d "$(WRGG_DEVNAME)" \
-s "$(WRGG_SIGNATURE)" \
-v "" -m "" -B ""
mv $@.new $@
endef
define Device/8dev_habanero-dvk
$(call Device/FitImageLzma)
DEVICE_VENDOR := 8devices
DEVICE_MODEL := Habanero DVK
IMAGE_SIZE := 30976k
SOC := qcom-ipq4019
IMAGE/sysupgrade.bin := append-kernel | pad-to 64k | append-rootfs | pad-rootfs | check-size | append-metadata
endef
TARGET_DEVICES += 8dev_habanero-dvk
define Device/8dev_jalapeno-common
$(call Device/FitImage)
$(call Device/UbiFit)
BLOCKSIZE := 128k
PAGESIZE := 2048
SOC := qcom-ipq4018
endef
define Device/8dev_jalapeno
$(call Device/8dev_jalapeno-common)
DEVICE_VENDOR := 8devices
DEVICE_MODEL := Jalapeno
endef
TARGET_DEVICES += 8dev_jalapeno
define Device/alfa-network_ap120c-ac
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := ALFA Network
DEVICE_MODEL := AP120C-AC
SOC := qcom-ipq4018
DEVICE_PACKAGES := kmod-usb-acm kmod-tpm-i2c-atmel
BLOCKSIZE := 128k
PAGESIZE := 2048
IMAGE_SIZE := 65536k
IMAGES := factory.bin sysupgrade.bin
IMAGE/factory.bin := append-ubi | qsdk-ipq-factory-nand
endef
TARGET_DEVICES += alfa-network_ap120c-ac
define Device/aruba_glenmorangie
$(call Device/FitImageLzma)
DEVICE_VENDOR := Aruba
SOC := qcom-ipq4029
endef
define Device/aruba_ap-303
$(call Device/aruba_glenmorangie)
DEVICE_MODEL := AP-303
endef
TARGET_DEVICES += aruba_ap-303
define Device/aruba_ap-303h
$(call Device/aruba_glenmorangie)
DEVICE_MODEL := AP-303H
endef
TARGET_DEVICES += aruba_ap-303h
define Device/aruba_ap-365
$(call Device/aruba_glenmorangie)
DEVICE_MODEL := AP-365
DEVICE_PACKAGES := kmod-hwmon-ad7418
endef
TARGET_DEVICES += aruba_ap-365
define Device/asus_map-ac2200
$(call Device/FitImageLzma)
DEVICE_VENDOR := ASUS
DEVICE_MODEL := Lyra (MAP-AC2200)
SOC := qcom-ipq4019
DEVICE_PACKAGES := ath10k-firmware-qca9888-ct kmod-ath3k
endef
TARGET_DEVICES += asus_map-ac2200
# WARNING: this is an initramfs image that gets you half of the way there
# you need to delete the jffs2 ubi volume and sysupgrade to the final image
# to get a "trx" you can flash via web UI for ac42u/ac58u:
# - change call Device/FitImageLzma to Device/FitImage
# - add the following below UIMAGE_NAME
# UIMAGE_MAGIC := 0x27051956
# IMAGES += factory.trx
# IMAGE/factory.trx := copy-file $(KDIR)/tmp/$$(KERNEL_INITRAMFS_IMAGE) | uImage none
define Device/asus_rt-ac42u
$(call Device/FitImageLzma)
DEVICE_VENDOR := ASUS
DEVICE_MODEL := RT-AC42U
DEVICE_ALT0_VENDOR := ASUS
DEVICE_ALT0_MODEL := RT-ACRH17
DEVICE_ALT1_VENDOR := ASUS
DEVICE_ALT1_MODEL := RT-AC2200
SOC := qcom-ipq4019
BLOCKSIZE := 128k
PAGESIZE := 2048
IMAGE_SIZE := 20439364
FILESYSTEMS := squashfs
# RT-AC82U is nowhere to be found online
# Rather, this device is a/k/a RT-AC42U
# But we'll go with what the vendor firmware has...
UIMAGE_NAME:=$(shell echo -e '\03\01\01\01RT-AC82U')
DEVICE_PACKAGES := ath10k-firmware-qca9984-ct kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += asus_rt-ac42u
define Device/asus_rt-ac58u
$(call Device/FitImageLzma)
DEVICE_VENDOR := ASUS
DEVICE_MODEL := RT-AC58U
DEVICE_ALT0_VENDOR := ASUS
DEVICE_ALT0_MODEL := RT-ACRH13
SOC := qcom-ipq4018
BLOCKSIZE := 128k
PAGESIZE := 2048
IMAGE_SIZE := 20439364
FILESYSTEMS := squashfs
# Someone - in their infinite wisdom - decided to put the firmware
# version in front of the image name \03\00\00\04 => Version 3.0.0.4
# Since u-boot works with strings we either need another fixup step
# to add a version... or we are very careful not to add '\0' into that
# string and call it a day.... Yeah, we do the latter!
UIMAGE_NAME:=$(shell echo -e '\03\01\01\01RT-AC58U')
DEVICE_PACKAGES := -kmod-ath10k-ct kmod-ath10k-ct-smallbuffers \
kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += asus_rt-ac58u
define Device/avm_fritzbox-4040
$(call Device/FitImageLzma)
DEVICE_VENDOR := AVM
DEVICE_MODEL := FRITZ!Box 4040
SOC := qcom-ipq4018
BOARD_NAME := fritz4040
IMAGE_SIZE := 29056k
UBOOT_PATH := $(STAGING_DIR_IMAGE)/uboot-fritz4040.bin
UBOOT_PARTITION_SIZE := 524288
IMAGES += eva.bin
IMAGE/eva.bin := append-uboot | pad-to $$$$(UBOOT_PARTITION_SIZE) | append-kernel | append-rootfs | pad-rootfs
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | check-size | append-metadata
DEVICE_PACKAGES := fritz-tffs fritz-caldata
endef
TARGET_DEVICES += avm_fritzbox-4040
define Device/avm_fritzbox-7530
$(call Device/FitImageLzma)
DEVICE_VENDOR := AVM
DEVICE_MODEL := FRITZ!Box 7530
DEVICE_ALT0_VENDOR := AVM
DEVICE_ALT0_MODEL := FRITZ!Box 7520
SOC := qcom-ipq4019
DEVICE_PACKAGES := fritz-caldata fritz-tffs-nand ltq-vdsl-vr11-app
endef
TARGET_DEVICES += avm_fritzbox-7530
define Device/avm_fritzrepeater-1200
$(call Device/FitImageLzma)
DEVICE_VENDOR := AVM
DEVICE_MODEL := FRITZ!Repeater 1200
SOC := qcom-ipq4019
DEVICE_PACKAGES := fritz-caldata fritz-tffs-nand
endef
TARGET_DEVICES += avm_fritzrepeater-1200
define Device/avm_fritzrepeater-3000
$(call Device/FitImageLzma)
DEVICE_VENDOR := AVM
DEVICE_MODEL := FRITZ!Repeater 3000
SOC := qcom-ipq4019
DEVICE_PACKAGES := ath10k-firmware-qca9984-ct fritz-caldata fritz-tffs-nand
endef
TARGET_DEVICES += avm_fritzrepeater-3000
define Device/buffalo_wtr-m2133hp
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := Buffalo
DEVICE_MODEL := WTR-M2133HP
SOC := qcom-ipq4019
DEVICE_PACKAGES := ath10k-firmware-qca9984-ct
BLOCKSIZE := 128k
PAGESIZE := 2048
endef
TARGET_DEVICES += buffalo_wtr-m2133hp
define Device/cellc_rtl30vw
KERNEL_SUFFIX := -zImage.itb
KERNEL_INITRAMFS = kernel-bin | gzip | fit gzip $$(KDIR)/image-$$(DEVICE_DTS).dtb
KERNEL = kernel-bin | fit none $$(KDIR)/image-$$(DEVICE_DTS).dtb | uImage lzma | pad-to 2048
KERNEL_NAME := zImage
KERNEL_IN_UBI :=
IMAGES := factory.bin sysupgrade.bin
IMAGE/factory.bin := append-rootfshdr kernel | append-ubi | qsdk-ipq-factory-nand-askey kernel
IMAGE/sysupgrade.bin := append-rootfshdr kernel | sysupgrade-tar kernel=$$$$@.kernel | append-metadata
DEVICE_VENDOR := Cell C
DEVICE_MODEL := RTL30VW
SOC := qcom-ipq4019
DEVICE_DTS_CONFIG := config@5
KERNEL_INSTALL := 1
KERNEL_SIZE := 4096k
IMAGE_SIZE := 57344k
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_PACKAGES := kmod-usb-net-qmi-wwan kmod-usb-serial-option uqmi
endef
TARGET_DEVICES += cellc_rtl30vw
define Device/cilab_meshpoint-one
$(call Device/8dev_jalapeno-common)
DEVICE_VENDOR := Crisis Innovation Lab
DEVICE_MODEL := MeshPoint.One
DEVICE_PACKAGES += kmod-i2c-gpio kmod-iio-bmp280-i2c kmod-hwmon-ina2xx kmod-rtc-pcf2127
endef
# Missing DSA Setup
#TARGET_DEVICES += cilab_meshpoint-one
define Device/compex_wpj419
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := Compex
DEVICE_MODEL := WPJ419
SOC := qcom-ipq4019
DEVICE_DTS_CONFIG := config@12
KERNEL_INSTALL := 1
BLOCKSIZE := 128k
PAGESIZE := 2048
FILESYSTEMS := squashfs
endef
# Missing DSA Setup
#TARGET_DEVICES += compex_wpj419
define Device/compex_wpj428
$(call Device/FitImage)
DEVICE_VENDOR := Compex
DEVICE_MODEL := WPJ428
SOC := qcom-ipq4028
DEVICE_DTS_CONFIG := config@4
BLOCKSIZE := 64k
IMAGE_SIZE := 31232k
KERNEL_SIZE := 4096k
IMAGES += cpximg-6a04.bin
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
IMAGE/cpximg-6a04.bin := append-kernel | append-rootfs | pad-rootfs | mkmylofw_32m 0x8A2 3
DEVICE_PACKAGES := kmod-gpio-beeper
DEFAULT := n
endef
TARGET_DEVICES += compex_wpj428
define Device/devolo_magic-2-wifi-next
$(call Device/FitImage)
DEVICE_VENDOR := devolo
DEVICE_MODEL := Magic 2 WiFi next
SOC := qcom-ipq4018
KERNEL_SIZE := 4096k
# If the bootloader sees 0xDEADC0DE and this trailer at the 64k boundary of a TFTP image
# it will bootm it, just like we want for the initramfs.
KERNEL_INITRAMFS := kernel-bin | gzip | fit gzip $$(KDIR)/image-$$(DEVICE_DTS).dtb | pad-to 64k |\
append-string -e '\xDE\xAD\xC0\xDE{"fl_initramfs":""}\x00'
IMAGE_SIZE := 26624k
IMAGES := sysupgrade.bin
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
DEFAULT := n
endef
# Missing DSA Setup
#TARGET_DEVICES += devolo_magic-2-wifi-next
define Device/dlink_dap-2610
$(call Device/FitImageLzma)
DEVICE_VENDOR := D-Link
DEVICE_MODEL := DAP-2610
SOC := qcom-ipq4018
DEVICE_DTS_CONFIG := config@ap.dk01.1-c1
BLOCKSIZE := 64k
WRGG_DEVNAME := /dev/mtdblock/8
WRGG_SIGNATURE := wapac30_dkbs_dap2610
IMAGE_SIZE := 14080k
IMAGES += factory.bin
# Bootloader expects a special 160 byte header which is added by
# wrgg-image.
# Factory image size must be larger than 6MB, and size in wrgg header must
# match actual factory image size to be flashable from D-Link http server.
# Bootloader verifies checksum of wrgg image before booting, thus jffs2
# cannot be part of the wrgg image. This is solved in the factory image by
# having the rootfs at the end of the image (without pad-rootfs). And in
# the sysupgrade image only the kernel is included in the wrgg checksum,
# but this is not flashable from the D-link http server.
# append-rootfs must start on an erase block boundary.
IMAGE/factory.bin := append-kernel | pad-offset 6144k 160 | append-rootfs | wrgg-image | check-size
IMAGE/sysupgrade.bin := append-kernel | wrgg-image | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | check-size | append-metadata
endef
TARGET_DEVICES += dlink_dap-2610
define Device/edgecore_ecw5211
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := Edgecore
DEVICE_MODEL := ECW5211
SOC := qcom-ipq4018
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_DTS_CONFIG := config@ap.dk01.1-c2
DEVICE_PACKAGES := kmod-tpm-i2c-atmel kmod-usb-acm
endef
TARGET_DEVICES += edgecore_ecw5211
define Device/edgecore_oap100
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := Edgecore
DEVICE_MODEL := OAP100
SOC := qcom-ipq4019
BLOCKSIZE := 128k
PAGESIZE := 2048
IMAGES := sysupgrade.bin
DEVICE_DTS_CONFIG := config@ap.dk07.1-c1
DEVICE_PACKAGES := kmod-usb-acm kmod-usb-net kmod-usb-net-cdc-qmi uqmi
endef
# Missing DSA Setup
#TARGET_DEVICES += edgecore_oap100
define Device/engenius_eap1300
$(call Device/FitImage)
DEVICE_VENDOR := EnGenius
DEVICE_MODEL := EAP1300
DEVICE_DTS_CONFIG := config@4
BOARD_NAME := eap1300
SOC := qcom-ipq4018
KERNEL_SIZE := 5120k
IMAGE_SIZE := 25344k
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
endef
# Missing DSA Setup
#TARGET_DEVICES += engenius_eap1300
define Device/engenius_eap2200
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := EnGenius
DEVICE_MODEL := EAP2200
SOC := qcom-ipq4019
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_PACKAGES := ath10k-firmware-qca9888-ct -kmod-ath10k-ct kmod-ath10k-ct-smallbuffers
endef
# Missing DSA Setup
#TARGET_DEVICES += engenius_eap2200
define Device/engenius_emd1
$(call Device/FitImage)
DEVICE_VENDOR := EnGenius
DEVICE_MODEL := EMD1
DEVICE_DTS_CONFIG := config@4
SOC := qcom-ipq4018
IMAGE_SIZE := 30720k
IMAGES += factory.bin
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
IMAGE/factory.bin := qsdk-ipq-factory-nor | check-size
endef
# Missing DSA Setup
#TARGET_DEVICES += engenius_emd1
define Device/engenius_emr3500
$(call Device/FitImage)
DEVICE_VENDOR := EnGenius
DEVICE_MODEL := EMR3500
DEVICE_DTS_CONFIG := config@4
SOC := qcom-ipq4018
KERNEL_SIZE := 4096k
IMAGE_SIZE := 30720k
IMAGES += factory.bin
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
IMAGE/factory.bin := qsdk-ipq-factory-nor | check-size
DEFAULT := n
endef
# Missing DSA Setup
#TARGET_DEVICES += engenius_emr3500
define Device/engenius_ens620ext
$(call Device/FitImage)
DEVICE_VENDOR := EnGenius
DEVICE_MODEL := ENS620EXT
SOC := qcom-ipq4018
DEVICE_DTS_CONFIG := config@4
BLOCKSIZE := 64k
PAGESIZE := 256
BOARD_NAME := ENS620EXT
VENDOR_ID := 0x0101
PRODUCT_ID := 0x79
PRODUCT_ID_NEW := 0xA4
DATECODE := 190507
FW_VER := 3.1.2
FW_VER_NEW := 3.5.6
CW_VER := 1.8.99
IMAGE_SIZE := 21312k
KERNEL_SIZE := 5120k
FILESYSTEMS := squashfs
IMAGES += factory_30.bin factory_35.bin
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | check-size | append-metadata
IMAGE/factory_30.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-rootfs | pad-rootfs | check-size | SenaoFW $$$$(PRODUCT_ID) $$$$(FW_VER)
IMAGE/factory_35.bin := qsdk-ipq-factory-nor | check-size | SenaoFW $$$$(PRODUCT_ID_NEW) $$$$(FW_VER_NEW)
endef
# Missing DSA Setup
#TARGET_DEVICES += engenius_ens620ext
define Device/extreme-networks_ws-ap3915i
$(call Device/FitImage)
DEVICE_VENDOR := Extreme Networks
DEVICE_MODEL := WS-AP3915i
IMAGE_SIZE := 30080k
SOC := qcom-ipq4029
BLOCKSIZE := 128k
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | check-size | append-metadata
endef
TARGET_DEVICES += extreme-networks_ws-ap3915i
define Device/ezviz_cs-w3-wd1200g-eup
$(call Device/FitImage)
DEVICE_VENDOR := EZVIZ
DEVICE_MODEL := CS-W3-WD1200G
DEVICE_VARIANT := EUP
IMAGE_SIZE := 14848k
KERNEL_SIZE = 6m
SOC := qcom-ipq4018
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | \
append-metadata
DEVICE_PACKAGES := -kmod-ath10k-ct kmod-ath10k-ct-smallbuffers
DEVICE_COMPAT_VERSION := 2.0
DEVICE_COMPAT_MESSAGE := uboot's bootcmd has to be updated (see wiki). \
Upgrade via sysupgrade mechanism is not possible.
endef
TARGET_DEVICES += ezviz_cs-w3-wd1200g-eup
define Device/glinet_gl-a1300
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := GL.iNet
DEVICE_MODEL := GL-A1300
SOC := qcom-ipq4018
DEVICE_DTS_CONFIG := config@ap.dk01.1-c2
BLOCKSIZE := 128k
PAGESIZE := 2048
IMAGE_SIZE := 131072k
endef
TARGET_DEVICES += glinet_gl-a1300
define Device/glinet_gl-ap1300
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := GL.iNet
DEVICE_MODEL := GL-AP1300
SOC := qcom-ipq4018
DEVICE_DTS_CONFIG := config@ap.dk01.1-c2
BLOCKSIZE := 128k
PAGESIZE := 2048
IMAGE_SIZE := 131072k
KERNEL_INSTALL := 1
DEVICE_PACKAGES := kmod-usb-net-qmi-wwan kmod-usb-serial-option uqmi
endef
TARGET_DEVICES += glinet_gl-ap1300
define Device/glinet_gl-b1300
$(call Device/FitzImage)
DEVICE_VENDOR := GL.iNet
DEVICE_MODEL := GL-B1300
BOARD_NAME := gl-b1300
SOC := qcom-ipq4029
KERNEL_SIZE := 4096k
IMAGE_SIZE := 26624k
IMAGE/sysupgrade.bin := append-kernel |append-rootfs | pad-rootfs | append-metadata
endef
TARGET_DEVICES += glinet_gl-b1300
define Device/glinet_gl-b2200
$(call Device/FitzImage)
DEVICE_VENDOR := GL.iNet
DEVICE_MODEL := GL-B2200
SOC := qcom-ipq4019
DEVICE_DTS_CONFIG := config@ap.dk04.1-c3
KERNEL_INITRAMFS_SUFFIX := -recovery.itb
IMAGES := emmc.img.gz sysupgrade.bin
IMAGE/emmc.img.gz := qsdk-ipq-app-gpt |\
pad-to 1024k | append-kernel |\
pad-to 33792k | append-rootfs |\
append-metadata | gzip
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
DEVICE_PACKAGES := ath10k-firmware-qca9888-ct \
kmod-fs-ext4 kmod-mmc kmod-spi-dev mkf2fs e2fsprogs kmod-fs-f2fs
endef
TARGET_DEVICES += glinet_gl-b2200
define Device/glinet_gl-s1300
$(call Device/FitzImage)
DEVICE_VENDOR := GL.iNet
DEVICE_MODEL := GL-S1300
SOC := qcom-ipq4029
KERNEL_SIZE := 4096k
IMAGE_SIZE := 26624k
IMAGES := sysupgrade.bin
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
DEVICE_PACKAGES := kmod-fs-ext4 kmod-mmc kmod-spi-dev
endef
# Missing DSA Setup
#TARGET_DEVICES += glinet_gl-s1300
define Device/kernel-size-6350-8300
DEVICE_COMPAT_VERSION := 2.0
DEVICE_COMPAT_MESSAGE := Kernel partition size must be increased for \
this OpenWrt version. Before continuing, you MUST issue either the \
command "fw_setenv kernsize 500000" from the OpenWrt command line, \
or "setenv kernsize 500000 ; saveenv" from the U-Boot serial console. \
Instead of the sysupgrade image, you must then install the OpenWrt \
factory image, setting the force flag and wiping the configuration. \
(e.g. "sysupgrade -n -F openwrt-squashfs-factory.bin" on command line)
endef
define Device/linksys_ea6350v3
# The Linksys EA6350v3 has a uboot bootloader that does not
# support either booting lzma kernel images nor booting UBI
# partitions. This uboot, however, supports raw kernel images and
# gzipped images.
#
# As configured by the OEM factory, the device will boot the kernel
# from a fixed address with a fixed length of 3 MiB. Also, the
# device has a hard-coded kernel command line that requires the
# rootfs and alt_rootfs to be in mtd11 and mtd13 respectively.
# Oh... and the kernel partition overlaps with the rootfs
# partition (the same for alt_kernel and alt_rootfs).
#
# If you are planing re-partitioning the device, you may want to
# keep these details in mind:
# 1. The kernel addresses you should honor are 0x00000000 and
# 0x02800000 respectively.
# 2. The kernel size (plus the dtb) cannot exceed 3 MiB in size
# unless the uboot environment variable "kernsize" is increased.
# 3. You can use 'zImage', but not a raw 'Image' packed with lzma.
# 4. The kernel command line from uboot is harcoded to boot with
# rootfs either in mtd11 or mtd13.
$(call Device/FitzImage)
$(call Device/kernel-size-6350-8300)
DEVICE_VENDOR := Linksys
DEVICE_MODEL := EA6350
DEVICE_VARIANT := v3
SOC := qcom-ipq4018
BLOCKSIZE := 128k
PAGESIZE := 2048
KERNEL_SIZE := 5120k
IMAGE_SIZE := 35840k
UBINIZE_OPTS := -E 5
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | append-uImage-fakehdr filesystem | pad-to $$$$(KERNEL_SIZE) | append-ubi | linksys-image type=EA6350v3
endef
TARGET_DEVICES += linksys_ea6350v3
define Device/linksys_ea8300
$(call Device/FitzImage)
$(call Device/kernel-size-6350-8300)
DEVICE_VENDOR := Linksys
DEVICE_MODEL := EA8300
SOC := qcom-ipq4019
KERNEL_SIZE := 5120k
IMAGE_SIZE := 84992k
BLOCKSIZE := 128k
PAGESIZE := 2048
UBINIZE_OPTS := -E 5 # EOD marks to "hide" factory sig at EOF
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | linksys-image type=EA8300
DEVICE_PACKAGES := ath10k-firmware-qca9888-ct kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += linksys_ea8300
define Device/linksys_mr8300
$(call Device/FitzImage)
$(call Device/kernel-size-6350-8300)
DEVICE_VENDOR := Linksys
DEVICE_MODEL := MR8300
SOC := qcom-ipq4019
KERNEL_SIZE := 5120k
IMAGE_SIZE := 84992k
BLOCKSIZE := 128k
PAGESIZE := 2048
UBINIZE_OPTS := -E 5 # EOD marks to "hide" factory sig at EOF
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | linksys-image type=MR8300
DEVICE_PACKAGES := ath10k-firmware-qca9888-ct kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += linksys_mr8300
define Device/linksys_whw03v2
$(call Device/FitzImage)
DEVICE_VENDOR := Linksys
DEVICE_MODEL := WHW03
DEVICE_VARIANT := V2
SOC := qcom-ipq4019
KERNEL_SIZE := 6144k
IMAGE_SIZE := 158720k
BLOCKSIZE := 128k
PAGESIZE := 2048
UBINIZE_OPTS := -E 5 # EOD marks to "hide" factory sig at EOF
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | linksys-image type=WHW03v2
DEVICE_PACKAGES := ath10k-firmware-qca9888-ct kmod-leds-pca963x kmod-spi-dev kmod-bluetooth
endef
TARGET_DEVICES += linksys_whw03v2
define Device/linksys_whw01
$(call Device/FitzImage)
DEVICE_VENDOR := Linksys
DEVICE_MODEL := WHW01
KERNEL_SIZE := 6144k
IMAGE_SIZE := 75776K
SOC := qcom-ipq4018
BLOCKSIZE := 128k
PAGESIZE := 2048
UBINIZE_OPTS := -E 5 # EOD marks to "hide" factory sig at EOF
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | linksys-image type=WHW01
DEVICE_PACKAGES := uboot-envtools kmod-leds-pca963x
endef
TARGET_DEVICES += linksys_whw01
define Device/luma_wrtq-329acn
$(call Device/FitImage)
DEVICE_VENDOR := Luma Home
DEVICE_MODEL := WRTQ-329ACN
SOC := qcom-ipq4018
DEVICE_PACKAGES := kmod-ath3k kmod-eeprom-at24 kmod-i2c-gpio
IMAGE_SIZE := 76632k
BLOCKSIZE := 128k
PAGESIZE := 2048
endef
TARGET_DEVICES += luma_wrtq-329acn
define Device/meraki_mr33
$(call Device/FitImage)
DEVICE_VENDOR := Cisco Meraki
DEVICE_MODEL := MR33
SOC := qcom-ipq4029
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_PACKAGES := -swconfig ath10k-firmware-qca9887-ct
DEFAULT := n
endef
TARGET_DEVICES += meraki_mr33
define Device/meraki_mr74
$(call Device/FitImage)
DEVICE_VENDOR := Cisco Meraki
DEVICE_MODEL := MR74
SOC := qcom-ipq4029
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_PACKAGES := -swconfig ath10k-firmware-qca9887-ct
DEVICE_DTS_CONFIG := config@3
DEFAULT := n
endef
TARGET_DEVICES += meraki_mr74
define Device/mobipromo_cm520-79f
$(call Device/FitzImage)
$(call Device/UbiFit)
DEVICE_VENDOR := MobiPromo
DEVICE_MODEL := CM520-79F
SOC := qcom-ipq4019
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_PACKAGES := kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += mobipromo_cm520-79f
define Device/netgear_ex61x0v2
$(call Device/DniImage)
DEVICE_VENDOR := NETGEAR
DEVICE_DTS_CONFIG := config@4
NETGEAR_BOARD_ID := EX6150v2series
NETGEAR_HW_ID := 29765285+16+0+128+2x2
IMAGE_SIZE := 14400k
SOC := qcom-ipq4018
endef
define Device/netgear_ex6100v2
$(call Device/netgear_ex61x0v2)
DEVICE_MODEL := EX6100
DEVICE_VARIANT := v2
endef
TARGET_DEVICES += netgear_ex6100v2
define Device/netgear_ex6150v2
$(call Device/netgear_ex61x0v2)
DEVICE_MODEL := EX6150
DEVICE_VARIANT := v2
endef
TARGET_DEVICES += netgear_ex6150v2
define Device/netgear_orbi
$(call Device/DniImage)
SOC := qcom-ipq4019
DEVICE_VENDOR := NETGEAR
IMAGE/factory.img := append-kernel | pad-offset 128k 64 | \
append-uImage-fakehdr filesystem | pad-to $$$$(KERNEL_SIZE) | \
append-rootfs | pad-rootfs | netgear-dni
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-to 64k | \
sysupgrade-tar rootfs=$$$$@ | append-metadata
DEVICE_PACKAGES := ath10k-firmware-qca9984-ct e2fsprogs kmod-fs-ext4 losetup
endef
define Device/netgear_rbx50
$(call Device/netgear_orbi)
NETGEAR_HW_ID := 29765352+0+4000+512+2x2+2x2+4x4
KERNEL_SIZE := 3932160
ROOTFS_SIZE := 32243712
IMAGE_SIZE := 36175872
endef
define Device/netgear_rbr50
$(call Device/netgear_rbx50)
DEVICE_MODEL := RBR50
DEVICE_VARIANT := v1
NETGEAR_BOARD_ID := RBR50
endef
TARGET_DEVICES += netgear_rbr50
define Device/netgear_rbs50
$(call Device/netgear_rbx50)
DEVICE_MODEL := RBS50
DEVICE_VARIANT := v1
NETGEAR_BOARD_ID := RBS50
endef
TARGET_DEVICES += netgear_rbs50
define Device/netgear_srx60
$(call Device/netgear_orbi)
NETGEAR_HW_ID := 29765352+0+4096+512+2x2+2x2+4x4
KERNEL_SIZE := 3932160
ROOTFS_SIZE := 32243712
IMAGE_SIZE := 36175872
endef
define Device/netgear_srr60
$(call Device/netgear_srx60)
DEVICE_MODEL := SRR60
NETGEAR_BOARD_ID := SRR60
endef
TARGET_DEVICES += netgear_srr60
define Device/netgear_srs60
$(call Device/netgear_srx60)
DEVICE_MODEL := SRS60
NETGEAR_BOARD_ID := SRS60
endef
TARGET_DEVICES += netgear_srs60
define Device/netgear_wac510
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := Netgear
DEVICE_MODEL := WAC510
SOC := qcom-ipq4018
DEVICE_DTS_CONFIG := config@5
BLOCKSIZE := 128k
PAGESIZE := 2048
IMAGES += factory.tar
IMAGE/factory.tar := append-ubi | wac5xx-netgear-tar
DEVICE_PACKAGES := uboot-envtools
endef
TARGET_DEVICES += netgear_wac510
define Device/openmesh_a42
$(call Device/FitImageLzma)
DEVICE_VENDOR := OpenMesh
DEVICE_MODEL := A42
SOC := qcom-ipq4018
DEVICE_DTS_CONFIG := config@om.a42
BLOCKSIZE := 64k
KERNEL = kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(DEVICE_DTS).dtb | pad-to $$(BLOCKSIZE)
IMAGE_SIZE := 15616k
IMAGES += factory.bin
IMAGE/factory.bin := append-rootfs | pad-rootfs | openmesh-image ce_type=A42
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata
endef
TARGET_DEVICES += openmesh_a42
define Device/openmesh_a62
$(call Device/FitImageLzma)
DEVICE_VENDOR := OpenMesh
DEVICE_MODEL := A62
SOC := qcom-ipq4019
DEVICE_DTS_CONFIG := config@om.a62
BLOCKSIZE := 64k
KERNEL = kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(DEVICE_DTS).dtb | pad-to $$(BLOCKSIZE)
IMAGE_SIZE := 15552k
IMAGES += factory.bin
IMAGE/factory.bin := append-rootfs | pad-rootfs | openmesh-image ce_type=A62
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata
DEVICE_PACKAGES := ath10k-firmware-qca9888-ct
endef
TARGET_DEVICES += openmesh_a62
define Device/p2w_r619ac
$(call Device/FitzImage)
$(call Device/UbiFit)
DEVICE_VENDOR := P&W
DEVICE_MODEL := R619AC
SOC := qcom-ipq4019
DEVICE_DTS_CONFIG := config@10
BLOCKSIZE := 128k
PAGESIZE := 2048
endef
define Device/p2w_r619ac-64m
$(call Device/p2w_r619ac)
DEVICE_VARIANT := 64M NAND
IMAGES += factory.bin
IMAGE/factory.bin := append-ubi | qsdk-ipq-factory-nand
endef
TARGET_DEVICES += p2w_r619ac-64m
define Device/p2w_r619ac-128m
$(call Device/p2w_r619ac)
DEVICE_VARIANT := 128M NAND
endef
TARGET_DEVICES += p2w_r619ac-128m
define Device/pakedge_wr-1
$(call Device/FitImageLzma)
DEVICE_VENDOR := Pakedge
DEVICE_MODEL := WR-1
DEVICE_DTS_CONFIG := config@ap.dk01.1-c1
SOC := qcom-ipq4018
BLOCKSIZE := 64k
IMAGE_SIZE := 31232k
IMAGE/sysupgrade.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | append-metadata
endef
TARGET_DEVICES += pakedge_wr-1
define Device/plasmacloud_pa1200
$(call Device/FitImageLzma)
DEVICE_VENDOR := Plasma Cloud
DEVICE_MODEL := PA1200
SOC := qcom-ipq4018
DEVICE_DTS_CONFIG := config@pc.pa1200
BLOCKSIZE := 64k
KERNEL = kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(DEVICE_DTS).dtb | pad-to $$(BLOCKSIZE)
IMAGE_SIZE := 15616k
IMAGES += factory.bin
IMAGE/factory.bin := append-rootfs | pad-rootfs | openmesh-image ce_type=PA1200
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata
endef
TARGET_DEVICES += plasmacloud_pa1200
define Device/plasmacloud_pa2200
$(call Device/FitImageLzma)
DEVICE_VENDOR := Plasma Cloud
DEVICE_MODEL := PA2200
SOC := qcom-ipq4019
DEVICE_DTS_CONFIG := config@pc.pa2200
BLOCKSIZE := 64k
KERNEL = kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(DEVICE_DTS).dtb | pad-to $$(BLOCKSIZE)
IMAGE_SIZE := 15552k
IMAGES += factory.bin
IMAGE/factory.bin := append-rootfs | pad-rootfs | openmesh-image ce_type=PA2200
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata
DEVICE_PACKAGES := ath10k-firmware-qca9888-ct
endef
TARGET_DEVICES += plasmacloud_pa2200
define Device/qcom_ap-dk01.1-c1
DEVICE_VENDOR := Qualcomm Atheros
DEVICE_MODEL := AP-DK01.1
DEVICE_VARIANT := C1
BOARD_NAME := ap-dk01.1-c1
SOC := qcom-ipq4019
DEVICE_DTS := qcom-ipq4019-ap.dk01.1-c1
KERNEL_INSTALL := 1
KERNEL_SIZE := 4096k
IMAGE_SIZE := 26624k
$(call Device/FitImage)
IMAGE/sysupgrade.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-rootfs | pad-rootfs | append-metadata
DEFAULT := n
endef
TARGET_DEVICES += qcom_ap-dk01.1-c1
define Device/qcom_ap-dk04.1-c1
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := Qualcomm Atheros
DEVICE_MODEL := AP-DK04.1
DEVICE_VARIANT := C1
SOC := qcom-ipq4019
DEVICE_DTS := qcom-ipq4019-ap.dk04.1-c1
KERNEL_INSTALL := 1
KERNEL_SIZE := 4048k
BLOCKSIZE := 128k
PAGESIZE := 2048
BOARD_NAME := ap-dk04.1-c1
DEFAULT := n
endef
TARGET_DEVICES += qcom_ap-dk04.1-c1
define Device/qxwlan_e2600ac-c1
$(call Device/FitImage)
DEVICE_VENDOR := Qxwlan
DEVICE_MODEL := E2600AC
DEVICE_VARIANT := C1
BOARD_NAME := e2600ac-c1
SOC := qcom-ipq4019
IMAGE_SIZE := 31232k
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
endef
TARGET_DEVICES += qxwlan_e2600ac-c1
define Device/qxwlan_e2600ac-c2
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := Qxwlan
DEVICE_MODEL := E2600AC
DEVICE_VARIANT := C2
SOC := qcom-ipq4019
KERNEL_INSTALL := 1
BLOCKSIZE := 128k
PAGESIZE := 2048
endef
TARGET_DEVICES += qxwlan_e2600ac-c2
define Device/sony_ncp-hg100-cellular
$(call Device/FitImage)
DEVICE_VENDOR := Sony
DEVICE_MODEL := NCP-HG100/Cellular
DEVICE_DTS_CONFIG := config@ap.dk04.1-c4
SOC := qcom-ipq4019
KERNEL_SIZE := 8192k
IMAGE_SIZE := 128m
DEVICE_PACKAGES := e2fsprogs kmod-fs-ext4 uqmi
endef
TARGET_DEVICES += sony_ncp-hg100-cellular
define Device/teltonika_rutx10
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := Teltonika
DEVICE_MODEL := RUTX10
SOC := qcom-ipq4018
DEVICE_DTS_CONFIG := config@5
KERNEL_INSTALL := 1
BLOCKSIZE := 128k
PAGESIZE := 2048
FILESYSTEMS := squashfs
IMAGE/factory.ubi := append-ubi | qsdk-ipq-factory-nand | append-rutx-metadata
DEVICE_PACKAGES := kmod-bluetooth
endef
# Missing DSA Setup
#TARGET_DEVICES += teltonika_rutx10
define Device/tel_x1pro
$(call Device/FitImage)
DEVICE_VENDOR := Telco
DEVICE_MODEL := X1 Pro
SOC := qcom-ipq4019
KERNEL_SIZE := 4096k
IMAGE_SIZE := 31232k
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
DEVICE_PACKAGES := kmod-usb-net-qmi-wwan kmod-usb-serial-option uqmi
DEFAULT := n
endef
# Missing DSA Setup
#TARGET_DEVICES += tel_x1pro
define Device/unielec_u4019-32m
$(call Device/FitImage)
DEVICE_VENDOR := Unielec
DEVICE_MODEL := U4019
DEVICE_VARIANT := 32M
BOARD_NAME := u4019-32m
SOC := qcom-ipq4019
KERNEL_SIZE := 4096k
IMAGE_SIZE := 31232k
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
DEFAULT := n
endef
# Missing DSA Setup
#TARGET_DEVICES += unielec_u4019-32m
define Device/wallys_dr40x9
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := Wallys
DEVICE_MODEL := DR40X9
SOC := qcom-ipq40x9
DEVICE_DTS_CONFIG := config@ap.dk07.1-c1
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_PACKAGES := ipq-wifi-wallys_dr40x9
endef
TARGET_DEVICES += wallys_dr40x9
define Device/zte_mf18a
$(call Device/FitImage)
DEVICE_VENDOR := ZTE
DEVICE_MODEL := MF18A
SOC := qcom-ipq4019
DEVICE_DTS_CONFIG := config@ap.dk04.1-c1
BLOCKSIZE := 128k
PAGESIZE := 2048
KERNEL_IN_UBI := 1
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct
endef
TARGET_DEVICES += zte_mf18a
define Device/zte_mf28x_common
$(call Device/FitzImage)
DEVICE_VENDOR := ZTE
SOC := qcom-ipq4019
DEVICE_DTS_CONFIG := config@ap.dk04.1-c1
BLOCKSIZE := 128k
PAGESIZE := 2048
KERNEL_IN_UBI := 1
DEVICE_PACKAGES := kmod-usb-net-qmi-wwan kmod-usb-serial-option uqmi
endef
define Device/zte_mf286d
$(call Device/zte_mf28x_common)
DEVICE_MODEL := MF286D
endef
TARGET_DEVICES += zte_mf286d
define Device/zte_mf287plus
$(call Device/zte_mf28x_common)
DEVICE_DTS_CONFIG := config@ap.dk01.1-c2
DEVICE_MODEL := MF287Plus
DEVICE_ALT0_VENDOR := ZTE
DEVICE_ALT0_MODEL := MF287
DEVICE_PACKAGES += ipq-wifi-zte_mf287plus
SOC := qcom-ipq4018
# The recovery image is used to return back to stock (an initramfs-based image
# that can be flashed to the device via sysupgrade
# The factory image is used to install from the stock firmware by using an
# exploit for the web interface
IMAGES += factory.bin recovery.bin
IMAGE/factory.bin := append-ubi
IMAGE/recovery.bin := append-squashfs4-fakeroot | sysupgrade-tar kernel=$$$$(BIN_DIR)/openwrt-$$(BOARD)$$(if $$(SUBTARGET),-$$(SUBTARGET))-$$(DEVICE_NAME)-initramfs-zImage.itb rootfs=$$$$@ | append-metadata
endef
TARGET_DEVICES += zte_mf287plus
define Device/zte_mf289f
$(call Device/zte_mf28x_common)
DEVICE_MODEL := MF289F
DEVICE_PACKAGES += ath10k-firmware-qca9984-ct
endef
TARGET_DEVICES += zte_mf289f
define Device/zyxel_nbg6617
$(call Device/FitImageLzma)
DEVICE_VENDOR := ZyXEL
DEVICE_MODEL := NBG6617
SOC := qcom-ipq4018
KERNEL_SIZE := 4096k
ROOTFS_SIZE := 24960k
RAS_BOARD := NBG6617
RAS_ROOTFS_SIZE := 19840k
RAS_VERSION := "$(VERSION_DIST) $(REVISION)"
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
IMAGES += factory.bin
# The ZyXEL firmware allows flashing thru the web-gui only when the rootfs is
# at least as large as the one of the initial firmware image (not the current
# one on the device). This only applies to the Web-UI, the bootlaoder ignores
# this minimum-size. However, the larger image can be flashed both ways.
IMAGE/factory.bin := append-rootfs | pad-rootfs | pad-to 64k | check-size $$$$(ROOTFS_SIZE) | zyxel-ras-image separate-kernel
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | check-size $$$$(ROOTFS_SIZE) | sysupgrade-tar rootfs=$$$$@ | append-metadata
DEVICE_PACKAGES := kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += zyxel_nbg6617
define Device/zyxel_wre6606
$(call Device/FitImage)
DEVICE_VENDOR := ZyXEL
DEVICE_MODEL := WRE6606
DEVICE_DTS_CONFIG := config@4
SOC := qcom-ipq4018
IMAGE_SIZE := 13184k
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | check-size | append-metadata
DEVICE_PACKAGES := -kmod-ath10k-ct kmod-ath10k-ct-smallbuffers
endef
# Missing DSA Setup
#TARGET_DEVICES += zyxel_wre6606
Reference in New Issue View Git Blame Copy Permalink