openwrt/target/linux/ramips/dts/mt7621_netgear_eax12.dts
Wenli Looi 32ea8a9a7e ramips: add support for Netgear EAX12 series
Netgear EAX12, EAX11v2, EAX15v2 are wall-plug 802.11ax (Wi-Fi 6)
extenders that share the SoC, WiFi chip, and image format with the
WAX202.

Specifications:
* MT7621, 256 MiB RAM, 128 MiB NAND
* MT7915: 2.4/5 GHz 2x2 802.11ax (DBDC)
* Ethernet: 1 port 10/100/1000
* UART: 115200 baud (labeled on board)

All LEDs and buttons appear to work without state_default.

Installation:
* Flash the factory image through the stock web interface, or TFTP to
  the bootloader. NMRP can be used to TFTP without opening the case.

Revert to stock firmware:
* Flash the stock firmware to the bootloader using TFTP/NMRP.

References in GPL source:
https://www.downloads.netgear.com/files/GPL/EAX12_EAX11v2_EAX15v2_GPL_V1.0.3.34_src.tar.gz

* target/linux/ramips/dts/mt7621-rfb-ax-nand.dts
  DTS file for this device.

Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
2023-07-01 14:42:11 +02:00

190 lines
2.9 KiB
Plaintext

// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
#include "mt7621.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
/ {
compatible = "netgear,eax12", "mediatek,mt7621-soc";
model = "Netgear EAX12";
aliases {
led-boot = &led_power_green;
led-failsafe = &led_power_red;
led-running = &led_power_green;
led-upgrade = &led_power_red;
};
chosen {
bootargs = "console=ttyS0,115200";
};
keys {
compatible = "gpio-keys";
reset {
label = "reset";
gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
};
wps {
label = "wps";
gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
linux,code = <KEY_WPS_BUTTON>;
};
};
leds {
compatible = "gpio-leds";
led_power_green: power_green {
label = "green:power";
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
};
led_power_red: power_red {
label = "red:power";
gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
};
client_green {
label = "green:client";
gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
};
client_red {
label = "red:client";
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
};
router_green {
label = "green:router";
gpios = <&gpio 5 GPIO_ACTIVE_HIGH>;
};
router_red {
label = "red:router";
gpios = <&gpio 11 GPIO_ACTIVE_HIGH>;
};
wps_green {
label = "green:wps";
gpios = <&gpio 17 GPIO_ACTIVE_HIGH>;
};
eth_green {
label = "green:eth";
gpios = <&gpio 10 GPIO_ACTIVE_LOW>;
};
eth_yellow {
label = "yellow:eth";
gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
};
};
};
&nand {
status = "okay";
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "Bootloader";
reg = <0x0 0x80000>;
read-only;
};
partition@80000 {
label = "Config";
reg = <0x80000 0x80000>;
read-only;
};
factory: partition@100000 {
label = "Factory";
reg = <0x100000 0x80000>;
read-only;
};
partition@180000 {
label = "firmware";
reg = <0x180000 0x3800000>;
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "kernel";
reg = <0x0 0x400000>;
};
partition@400000 {
label = "ubi";
reg = <0x400000 0x3400000>;
};
};
partition@2780000 {
label = "firmware_backup";
reg = <0x3980000 0x3800000>;
read-only;
};
partition@4d80000 {
label = "CFG";
reg = <0x7180000 0x200000>;
read-only;
};
partition@5580000 {
label = "RAE";
reg = <0x7380000 0x600000>;
read-only;
};
partition@5980000 {
label = "POT";
reg = <0x7980000 0x020000>;
read-only;
};
partition@6780000 {
label = "LOG";
reg = <0x79A0000 0x40000>;
read-only;
};
};
};
&pcie {
status = "okay";
};
&pcie1 {
wifi@0,0 {
compatible = "mediatek,mt76";
reg = <0x0000 0 0 0 0>;
mediatek,mtd-eeprom = <&factory 0x0>;
};
};
&switch0 {
ports {
port@0 {
status = "okay";
label = "lan";
};
};
};
&xhci {
status = "disabled";
};