mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-26 08:51:13 +00:00
844bb4bfad
Hardware
--------
CPU: Qualcomm IPQ4018
RAM: 256M
Flash: 16MB SPI-NOR (W25Q128)
128MB SPI-NAND (XTX)
WiFi: 2T2R (2GHz 802.11n ; 5 GHz 802.11ac)
ETH: 4x LAN ; 1x WAN (Gigabit)
CELL: Quectel RG501Q 3G/4G/5G
UART: Available on the goldfinger connector (Pinout silkscreened)
115200 8N1 3V3 - Only connect RX / TX / GND
Installation
------------
1. Enable SSH in the Teltonika UI
(System --> Administration --> Access Control)
2. Check from which partition set the device is currently running from.
$ cat /proc/boot_info/rootfs/primaryboot
In case this output reads 0, install a Software update from Teltonika
first. After upgrade completion, check this file now reads 1 before
continuing.
2. Transfer the OpenWrt factory image to the device using scp. Use the
same password (user root!) as used for the Web-UI.
$ scp -O openwrt-factory.bin root@192.168.1.1:/tmp
3. Connect to the device using ssh as the root user.
4. Install OpenWrt by writing the factory image to flash.
$ ubiformat /dev/mtd16 -y -f /tmp/openwrt-factory.bin
5. Instruct the bootloaer to boot from the first partition set.
$ echo 0 > /proc/boot_info/rootfs/primaryboot
$ cat /proc/boot_info/getbinary_bootconfig > /tmp/bootconfig.bin
$ cat /proc/boot_info/getbinary_bootconfig1 > /tmp/bootconfig1.bin
$ mtd write /tmp/bootconfig.bin /dev/mtd2
$ mtd write /tmp/bootconfig1.bin /dev/mtd3
6. Reboot the device.
$ reboot
Signed-off-by: David Bauer <mail@david-bauer.net>
281 lines
9.4 KiB
Bash
281 lines
9.4 KiB
Bash
#!/bin/sh
|
|
|
|
[ -e /lib/firmware/$FIRMWARE ] && exit 0
|
|
|
|
. /lib/functions/caldata.sh
|
|
|
|
board=$(board_name)
|
|
|
|
case "$FIRMWARE" in
|
|
"ath10k/cal-pci-0000:01:00.0.bin")
|
|
case "$board" in
|
|
meraki,mr33 |\
|
|
meraki,mr74)
|
|
caldata_extract_ubi "ART" 0x9000 0x844
|
|
caldata_valid "4408" || caldata_extract "ART" 0x9000 0x844
|
|
;;
|
|
esac
|
|
;;
|
|
"ath10k/pre-cal-pci-0000:01:00.0.bin")
|
|
case "$board" in
|
|
asus,map-ac2200)
|
|
caldata_extract_ubi "Factory" 0x9000 0x2f20
|
|
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
|
|
/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
|
|
;;
|
|
asus,rt-ac42u)
|
|
caldata_extract_ubi "Factory" 0x9000 0x2f20
|
|
;;
|
|
avm,fritzrepeater-3000)
|
|
/usr/bin/fritz_cal_extract -i 1 -s 0x3D000 -e 0x212 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader0") || \
|
|
/usr/bin/fritz_cal_extract -i 1 -s 0x3C800 -e 0x212 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader0") || \
|
|
/usr/bin/fritz_cal_extract -i 1 -s 0x3C000 -e 0x212 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader0") || \
|
|
/usr/bin/fritz_cal_extract -i 1 -s 0x3D000 -e 0x212 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1") || \
|
|
/usr/bin/fritz_cal_extract -i 1 -s 0x3C800 -e 0x212 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1") || \
|
|
/usr/bin/fritz_cal_extract -i 1 -s 0x3C000 -e 0x212 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1")
|
|
;;
|
|
linksys,ea8300 |\
|
|
linksys,mr8300)
|
|
caldata_extract "ART" 0x9000 0x2f20
|
|
# OEM assigns 4 sequential MACs
|
|
ath10k_patch_mac $(macaddr_setbit_la $(macaddr_add "$(cat /sys/class/net/eth0/address)" 4))
|
|
;;
|
|
netgear,rbr50|\
|
|
netgear,rbs50|\
|
|
netgear,srr60|\
|
|
netgear,srs60)
|
|
caldata_extract_mmc "0:ART" 0x9000 0x2f20
|
|
ath10k_patch_mac $(mmc_get_mac_binary ARTMTD 0x12)
|
|
;;
|
|
esac
|
|
;;
|
|
"ath10k/pre-cal-ahb-a000000.wifi.bin")
|
|
case "$board" in
|
|
qcom,ap-dk01.1-c1)
|
|
caldata_extract "ART" 0x1000 0x2f20
|
|
;;
|
|
asus,map-ac2200|\
|
|
asus,rt-ac42u|\
|
|
asus,rt-ac58u)
|
|
caldata_extract_ubi "Factory" 0x1000 0x2f20
|
|
;;
|
|
avm,fritzbox-4040)
|
|
/usr/bin/fritz_cal_extract -i 1 -s 0x400 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader_config")
|
|
;;
|
|
avm,fritzbox-7530 |\
|
|
avm,fritzrepeater-1200 |\
|
|
avm,fritzrepeater-3000)
|
|
/usr/bin/fritz_cal_extract -i 1 -s 0x3C000 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader0") || \
|
|
/usr/bin/fritz_cal_extract -i 1 -s 0x3C800 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader0") || \
|
|
/usr/bin/fritz_cal_extract -i 1 -s 0x3D000 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader0") || \
|
|
/usr/bin/fritz_cal_extract -i 1 -s 0x3C000 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1") || \
|
|
/usr/bin/fritz_cal_extract -i 1 -s 0x3C800 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1") || \
|
|
/usr/bin/fritz_cal_extract -i 1 -s 0x3D000 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1")
|
|
;;
|
|
cellc,rtl30vw)
|
|
caldata_extract "0:ART" 0x1000 0x2f20
|
|
;;
|
|
devolo,magic-2-wifi-next)
|
|
caldata_extract "ART" 0x1000 0x2f20
|
|
ath10k_patch_mac $(mtd_get_mac_ascii APPSBLENV WiFiMacAddress0)
|
|
;;
|
|
dlink,dap-2610)
|
|
caldata_extract "ART" 0x1000 0x2f20
|
|
ath10k_patch_mac $(mtd_get_mac_ascii bdcfg wlanmac)
|
|
;;
|
|
engenius,emd1)
|
|
caldata_extract "0:ART" 0x1000 0x2f20
|
|
ath10k_patch_mac $(mtd_get_mac_ascii 0:APPSBLENV wlanaddr)
|
|
;;
|
|
engenius,emr3500)
|
|
caldata_extract "0:ART" 0x1000 0x2f20
|
|
ath10k_patch_mac $(mtd_get_mac_ascii 0:APPSBLENV ethaddr)
|
|
;;
|
|
engenius,ens620ext)
|
|
caldata_extract "ART" 0x1000 0x2f20
|
|
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii u-boot-env ethaddr) 2)
|
|
;;
|
|
extreme-networks,ws-ap3915i)
|
|
caldata_extract "ART" 0x1000 0x2f20
|
|
ath10k_patch_mac $(mtd_get_mac_ascii CFG1 RADIOADDR0)
|
|
;;
|
|
linksys,ea8300 |\
|
|
linksys,mr8300)
|
|
caldata_extract "ART" 0x1000 0x2f20
|
|
ath10k_patch_mac $(macaddr_add "$(cat /sys/class/net/eth0/address)" 2)
|
|
;;
|
|
meraki,mr33 |\
|
|
meraki,mr74)
|
|
caldata_extract_ubi "ART" 0x1000 0x2f20
|
|
caldata_valid "202f" || caldata_extract "ART" 0x1000 0x2f20
|
|
;;
|
|
mikrotik,cap-ac |\
|
|
mikrotik,hap-ac2 |\
|
|
mikrotik,hap-ac3 |\
|
|
mikrotik,hap-ac3-lte6-kit |\
|
|
mikrotik,wap-ac |\
|
|
mikrotik,wap-ac-lte |\
|
|
mikrotik,wap-r-ac)
|
|
wlan_data="/sys/firmware/mikrotik/hard_config/wlan_data"
|
|
( [ -f "$wlan_data" ] && caldata_sysfsload_from_file "$wlan_data" 0x0 0x2f20 ) || \
|
|
( [ -d "$wlan_data" ] && caldata_sysfsload_from_file "$wlan_data/data_0" 0x0 0x2f20 )
|
|
;;
|
|
netgear,rbr50|\
|
|
netgear,rbs50|\
|
|
netgear,srr60|\
|
|
netgear,srs60)
|
|
caldata_extract_mmc "0:ART" 0x1000 0x2f20
|
|
ath10k_patch_mac $(mmc_get_mac_binary ARTMTD 0x0)
|
|
;;
|
|
pakedge,wr-1)
|
|
caldata_extract "0:ART" 0x1000 0x2f20
|
|
ath10k_patch_mac $(macaddr_add $(get_mac_label) 2)
|
|
;;
|
|
teltonika,rutx10|\
|
|
teltonika,rutx50)
|
|
caldata_extract "0:ART" 0x1000 0x2f20
|
|
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary "0:CONFIG" 0x0) 2)
|
|
;;
|
|
sony,ncp-hg100-cellular)
|
|
caldata_extract_mmc "0:ART" 0x1000 0x2f20
|
|
;;
|
|
zyxel,nbg6617 |\
|
|
zyxel,wre6606)
|
|
caldata_extract "ART" 0x1000 0x2f20
|
|
ath10k_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) -2)
|
|
;;
|
|
esac
|
|
;;
|
|
"ath10k/pre-cal-ahb-a800000.wifi.bin")
|
|
case "$board" in
|
|
qcom,ap-dk01.1-c1)
|
|
caldata_extract "ART" 0x5000 0x2f20
|
|
;;
|
|
asus,map-ac2200|\
|
|
asus,rt-ac58u)
|
|
caldata_extract_ubi "Factory" 0x5000 0x2f20
|
|
;;
|
|
avm,fritzbox-4040)
|
|
/usr/bin/fritz_cal_extract -i 1 -s 0x400 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader_config")
|
|
;;
|
|
avm,fritzbox-7530 |\
|
|
avm,fritzrepeater-1200 |\
|
|
avm,fritzrepeater-3000)
|
|
/usr/bin/fritz_cal_extract -i 1 -s 0x3C800 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader0") || \
|
|
/usr/bin/fritz_cal_extract -i 1 -s 0x3D000 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader0") || \
|
|
/usr/bin/fritz_cal_extract -i 1 -s 0x3C000 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader0") || \
|
|
/usr/bin/fritz_cal_extract -i 1 -s 0x3C800 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1") || \
|
|
/usr/bin/fritz_cal_extract -i 1 -s 0x3D000 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1") || \
|
|
/usr/bin/fritz_cal_extract -i 1 -s 0x3C000 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1")
|
|
;;
|
|
cellc,rtl30vw)
|
|
caldata_extract "0:ART" 0x5000 0x2f20
|
|
;;
|
|
devolo,magic-2-wifi-next)
|
|
caldata_extract "ART" 0x5000 0x2f20
|
|
ath10k_patch_mac $(mtd_get_mac_ascii APPSBLENV WiFiMacAddress1)
|
|
;;
|
|
dlink,dap-2610)
|
|
caldata_extract "ART" 0x5000 0x2f20
|
|
ath10k_patch_mac $(mtd_get_mac_ascii bdcfg wlanmac_a)
|
|
;;
|
|
engenius,emd1)
|
|
caldata_extract "0:ART" 0x5000 0x2f20
|
|
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii 0:APPSBLENV wlanaddr) 1)
|
|
;;
|
|
engenius,emr3500)
|
|
caldata_extract "0:ART" 0x5000 0x2f20
|
|
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii 0:APPSBLENV ethaddr) 1)
|
|
;;
|
|
engenius,ens620ext)
|
|
caldata_extract "ART" 0x5000 0x2f20
|
|
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii u-boot-env ethaddr) 3)
|
|
;;
|
|
extreme-networks,ws-ap3915i)
|
|
caldata_extract "ART" 0x5000 0x2f20
|
|
ath10k_patch_mac $(mtd_get_mac_ascii CFG1 RADIOADDR1)
|
|
;;
|
|
linksys,ea8300 |\
|
|
linksys,mr8300)
|
|
caldata_extract "ART" 0x5000 0x2f20
|
|
ath10k_patch_mac $(macaddr_add "$(cat /sys/class/net/eth0/address)" 3)
|
|
;;
|
|
meraki,mr33 |\
|
|
meraki,mr74)
|
|
caldata_extract_ubi "ART" 0x5000 0x2f20
|
|
caldata_valid "202f" || caldata_extract "ART" 0x5000 0x2f20
|
|
;;
|
|
mikrotik,cap-ac |\
|
|
mikrotik,hap-ac2 |\
|
|
mikrotik,hap-ac3 |\
|
|
mikrotik,hap-ac3-lte6-kit |\
|
|
mikrotik,sxtsq-5-ac |\
|
|
mikrotik,wap-ac |\
|
|
mikrotik,wap-ac-lte |\
|
|
mikrotik,wap-r-ac)
|
|
wlan_data="/sys/firmware/mikrotik/hard_config/wlan_data"
|
|
( [ -f "$wlan_data" ] && caldata_sysfsload_from_file "$wlan_data" 0x8000 0x2f20 ) || \
|
|
( [ -d "$wlan_data" ] && caldata_sysfsload_from_file "$wlan_data/data_2" 0x0 0x2f20 )
|
|
;;
|
|
netgear,rbr50|\
|
|
netgear,rbs50|\
|
|
netgear,srr60|\
|
|
netgear,srs60)
|
|
caldata_extract_mmc "0:ART" 0x5000 0x2f20
|
|
ath10k_patch_mac $(mmc_get_mac_binary ARTMTD 0xc)
|
|
;;
|
|
pakedge,wr-1)
|
|
caldata_extract "0:ART" 0x5000 0x2f20
|
|
ath10k_patch_mac $(macaddr_add $(get_mac_label) 4)
|
|
;;
|
|
teltonika,rutx10|\
|
|
teltonika,rutx50)
|
|
caldata_extract "0:ART" 0x5000 0x2f20
|
|
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary "0:CONFIG" 0x0) 3)
|
|
;;
|
|
sony,ncp-hg100-cellular)
|
|
caldata_extract_mmc "0:ART" 0x5000 0x2f20
|
|
;;
|
|
zyxel,nbg6617 |\
|
|
zyxel,wre6606)
|
|
caldata_extract "ART" 0x5000 0x2f20
|
|
ath10k_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) -1)
|
|
;;
|
|
esac
|
|
;;
|
|
"ath10k/QCA4019/hw1.0/board-ahb-a000000.wifi.bin")
|
|
case "$board" in
|
|
mikrotik,cap-ac |\
|
|
mikrotik,hap-ac2 |\
|
|
mikrotik,hap-ac3 |\
|
|
mikrotik,hap-ac3-lte6-kit |\
|
|
mikrotik,wap-ac |\
|
|
mikrotik,wap-ac-lte |\
|
|
mikrotik,wap-r-ac)
|
|
wlan_data="/sys/firmware/mikrotik/hard_config/wlan_data"
|
|
( [ -f "$wlan_data" ] && caldata_sysfsload_from_file "$wlan_data" 0x2f20 0x2f20 ) || \
|
|
( [ -d "$wlan_data" ] && caldata_sysfsload_from_file "$wlan_data/data_0" 0x2f20 0x2f20 )
|
|
;;
|
|
esac
|
|
;;
|
|
"ath10k/QCA4019/hw1.0/board-ahb-a800000.wifi.bin")
|
|
case "$board" in
|
|
mikrotik,cap-ac |\
|
|
mikrotik,hap-ac2 |\
|
|
mikrotik,hap-ac3 |\
|
|
mikrotik,hap-ac3-lte6-kit |\
|
|
mikrotik,sxtsq-5-ac |\
|
|
mikrotik,wap-ac |\
|
|
mikrotik,wap-ac-lte |\
|
|
mikrotik,wap-r-ac)
|
|
wlan_data="/sys/firmware/mikrotik/hard_config/wlan_data"
|
|
( [ -f "$wlan_data" ] && caldata_sysfsload_from_file "$wlan_data" 0xaf20 0x2f20 ) || \
|
|
( [ -d "$wlan_data" ] && caldata_sysfsload_from_file "$wlan_data/data_2" 0x2f20 0x2f20 )
|
|
;;
|
|
esac
|
|
;;
|
|
*)
|
|
exit 1
|
|
;;
|
|
esac
|