openwrt/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
Daniel Danzberger affe633be4 ipq40xx: ipq4019: Add new device Compex WPJ419
This device contains 2 flash devices. One NOR (32M) and one NAND (128M).
U-boot and caldata are on the NOR, the firmware on the NAND.

    SoC:    IPQ4019
    CPU:    4x 710MHz ARMv7
    RAM:    256MB
    FLASH:  NOR:32MB NAND:128MB
    ETH:    2x GMAC Gigabit
    POE:    802.3 af/at POE, IEEE802.3af/IEEE802.3at(48-56V)
    WIFI:   1x 2.4Ghz Atheros qca4019 2x2 MU-MIMO
            1x 5.0Ghz Atheros qca4019 2x2 MU-MIMO
    USB:    1x 3.0
    PCI:    1x Mini PCIe
    SIM:    1x Slot
    SD:     1x MicroSD slot
    BTN:    Reset
    LED:    - Power
            - Ethernet
    UART:  1x Serial Port 4 Pin Connector (UART)
           1x Serial Port 6 Pin Connector (High Speed UART)
    POWER: 12V 2A

Installation
------------
Initial flashing can only be done via u-boot using the following commands:

tftpboot openwrt-ipq40xx-generic-compex_wpj419-squashfs-nand-factory.ubi
nand erase.chip; nand write ${fileaddr} 0x0 ${filesize}
res

Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com>
2019-11-02 19:25:15 +01:00

100 lines
2.0 KiB
Bash

PART_NAME=firmware
REQUIRE_IMAGE_METADATA=1
RAMFS_COPY_BIN='fw_printenv fw_setenv'
RAMFS_COPY_DATA='/etc/fw_env.config /var/lock/fw_printenv.lock'
platform_check_image() {
case "$(board_name)" in
asus,rt-ac58u)
CI_UBIPART="UBI_DEV"
local ubidev=$(nand_find_ubi $CI_UBIPART)
local asus_root=$(nand_find_volume $ubidev jffs2)
[ -n "$asus_root" ] || return 0
cat << EOF
jffs2 partition is still present.
There's probably no space left
to install the filesystem.
You need to delete the jffs2 partition first:
# ubirmvol /dev/ubi0 --name=jffs2
Once this is done. Retry.
EOF
return 1
;;
esac
return 0;
}
zyxel_do_upgrade() {
local tar_file="$1"
local board_dir=$(tar tf $tar_file | grep -m 1 '^sysupgrade-.*/$')
board_dir=${board_dir%/}
tar Oxf $tar_file ${board_dir}/kernel | mtd write - kernel
if [ -n "$UPGRADE_BACKUP" ]; then
tar Oxf $tar_file ${board_dir}/root | mtd -j "$UPGRADE_BACKUP" write - rootfs
else
tar Oxf $tar_file ${board_dir}/root | mtd write - rootfs
fi
}
platform_do_upgrade() {
case "$(board_name)" in
8dev,jalapeno |\
avm,fritzbox-7530 |\
avm,fritzrepeater-1200 |\
avm,fritzrepeater-3000 |\
qxwlan,e2600ac-c2)
nand_do_upgrade "$1"
;;
alfa-network,ap120c-ac)
part="$(awk -F 'ubi.mtd=' '{printf $2}' /proc/cmdline | sed -e 's/ .*$//')"
if [ "$part" = "rootfs1" ]; then
fw_setenv active 2 || exit 1
CI_UBIPART="rootfs2"
else
fw_setenv active 1 || exit 1
CI_UBIPART="rootfs1"
fi
nand_do_upgrade "$1"
;;
asus,map-ac2200)
CI_KERNPART="linux"
nand_do_upgrade "$1"
;;
asus,rt-ac58u)
CI_UBIPART="UBI_DEV"
CI_KERNPART="linux"
nand_do_upgrade "$1"
;;
compex,wpj419)
nand_do_upgrade "$1"
;;
linksys,ea6350v3 |\
linksys,ea8300)
platform_do_upgrade_linksys "$1"
;;
meraki,mr33)
CI_KERNPART="part.safe"
nand_do_upgrade "$1"
;;
openmesh,a42 |\
openmesh,a62)
PART_NAME="inactive"
platform_do_upgrade_openmesh "$1"
;;
zyxel,nbg6617)
zyxel_do_upgrade "$1"
;;
*)
default_do_upgrade "$1"
;;
esac
}