mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-21 06:33:41 +00:00
7e4de89e63
This model is almost identical to the EAP225-Outdoor v1.
Major difference is the RTL8211FS PHY Chipset.
Device specifications:
* SoC: QCA9563 @ 775MHz
* Memory: 128MiB DDR2
* Flash: 16MiB SPI-NOR
* Wireless 2.4GHz (SoC): b/g/n 2x2
* Wireless 5GHz (QCA9886): a/n/ac 2x2 MU-MIMO
* Ethernet (RTL8211FS): 1× 1GbE, PoE
Flashing instructions:
* ssh into target device with recent (>= v1.6.0) firmware
* run `cliclientd stopcs` on target device
* upload factory image via web interface
Debricking:
To recover the device, you need access to the serial port. This requires
fine soldering to test points, or the use of probe pins.
* Open the case and solder wires to the test points: RXD, TXD and TPGND4
* Use a 3.3V UART, 115200 baud, 8n1
* Interrupt bootloader by holding ctrl+B during boot
* upload initramfs via built-in tftp client and perform sysupgrade
setenv ipaddr 192.168.1.1 # default, change as required
setenv serverip 192.168.1.10 # default, change as required
tftp 0x80800000 initramfs.bin
bootelf $fileaddr
MAC addresses:
MAC address (as on device label) is stored in device info partition at
an offset of 8 bytes. ath9k device has same address as ethernet, ath10k
uses address incremented by 1.
From stock ifconfig:
ath0 Link encap:Ethernet HWaddr D8:...:2E
ath10 Link encap:Ethernet HWaddr D8:...:2F
br0 Link encap:Ethernet HWaddr D8:...:2E
eth0 Link encap:Ethernet HWaddr D8:...:2E
Signed-off-by: Paul Maruhn <paulmaruhn@posteo.de>
Co-developed-by: Philipp Rothmann <philipprothmann@posteo.de>
Signed-off-by: Philipp Rothmann <philipprothmann@posteo.de>
[Add pre-calibraton nvme-cells]
Tested-by: Tido Klaassen <tido_ff@4gh.eu>
Signed-off-by: Nick Hainke <vincent@systemli.org>
60 lines
1.0 KiB
Plaintext
60 lines
1.0 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
#include "qca9563_tplink_eap2x5-1port.dtsi"
|
|
|
|
/ {
|
|
compatible = "tplink,eap225-outdoor-v3", "qca,qca9563";
|
|
model = "TP-Link EAP225-Outdoor v3";
|
|
|
|
aliases {
|
|
led-boot = &led_status_green;
|
|
led-failsafe = &led_status_amber;
|
|
led-running = &led_status_green;
|
|
led-upgrade = &led_status_amber;
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
led_status_green: status_green {
|
|
label = "green:status";
|
|
gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
|
|
default-state = "on";
|
|
};
|
|
|
|
led_status_amber: status_amber {
|
|
label = "amber:status";
|
|
gpios = <&gpio 9 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&art {
|
|
precalibration_ath10k: pre-calibration@5000 {
|
|
reg = <0x5000 0x2f20>;
|
|
};
|
|
};
|
|
|
|
ð0 {
|
|
phy-handle = <&phy6>;
|
|
phy-mode = "sgmii";
|
|
};
|
|
|
|
&mdio0 {
|
|
phy6: ethernet-phy@6 {
|
|
reg = <6>;
|
|
};
|
|
};
|
|
|
|
&pcie {
|
|
wifi@0,0 {
|
|
compatible = "qcom,ath10k";
|
|
reg = <0 0 0 0 0>;
|
|
|
|
mac-address-increment = <1>;
|
|
|
|
nvmem-cells = <&macaddr_info_8>, <&precalibration_ath10k>;
|
|
nvmem-cell-names = "mac-address", "pre-calibration";
|
|
};
|
|
};
|