mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-30 10:39:04 +00:00
9188c77cbe
The compex WPJ563 actually has both usb controllers wired: usb0 --> pci-e slot usb1 --> pin header As the board exposes it for generic use, enable this controller too. fixes: #13650 Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
156 lines
2.3 KiB
Plaintext
156 lines
2.3 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
#include "qca956x.dtsi"
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
model = "Compex WPJ563";
|
|
compatible = "compex,wpj563", "qca,qca9563";
|
|
|
|
aliases {
|
|
label-mac-device = ð0;
|
|
led-boot = &led_sig4;
|
|
led-failsafe = &led_sig4;
|
|
led-running = &led_sig4;
|
|
led-upgrade = &led_sig4;
|
|
};
|
|
|
|
beeper {
|
|
compatible = "gpio-beeper";
|
|
gpios = <&gpio 19 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
reset {
|
|
label = "reset";
|
|
linux,code = <KEY_RESTART>;
|
|
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
|
|
debounce-interval = <60>;
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
sig1 {
|
|
label = "green:sig1";
|
|
gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
sig2 {
|
|
label = "green:sig2";
|
|
gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
sig3 {
|
|
label = "green:sig4";
|
|
gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
led_sig4: sig4 {
|
|
label = "green:sig4";
|
|
gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&pcie {
|
|
status = "okay";
|
|
};
|
|
|
|
&spi {
|
|
status = "okay";
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <25000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
uboot: partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x000000 0x030000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@30000 {
|
|
compatible = "denx,uimage";
|
|
label = "firmware";
|
|
reg = <0x030000 0xfc0000>;
|
|
};
|
|
|
|
art: partition@ff0000 {
|
|
label = "art";
|
|
reg = <0xff0000 0x010000>;
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&mdio0 {
|
|
status = "okay";
|
|
|
|
phy0: ethernet-phy@0 {
|
|
reg = <0>;
|
|
phy-mode = "sgmii";
|
|
qca,mib-poll-interval = <500>;
|
|
|
|
qca,ar8327-initvals = <
|
|
0x04 0x00080080 /* PORT0 PAD MODE CTRL */
|
|
0x7c 0x0000007e /* PORT0_STATUS */
|
|
>;
|
|
};
|
|
};
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
|
|
pll-data = <0x03000101 0x00000101 0x00001919>;
|
|
|
|
nvmem-cells = <&macaddr_uboot_2e010>;
|
|
nvmem-cell-names = "mac-address";
|
|
phy-mode = "sgmii";
|
|
phy-handle = <&phy0>;
|
|
};
|
|
|
|
&usb_phy0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&usb0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&usb_phy1 {
|
|
status = "okay";
|
|
};
|
|
|
|
&usb1 {
|
|
status = "okay";
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
|
|
mtd-cal-data = <&art 0x1000>;
|
|
};
|
|
|
|
&uboot {
|
|
compatible = "nvmem-cells";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
macaddr_uboot_2e010: macaddr@2e010 {
|
|
reg = <0x2e010 0x6>;
|
|
};
|
|
};
|