mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-25 08:21:14 +00:00
d1016446da
The GL.iNet X3000 and XE3000 are Wi-Fi 6 5G cellular routers, based on MediaTek MT7981A SoC. The XE3000 is the same device as the X3000, except for an additional battery. Specifications: - SoC: Filogic 820 MT7981A (1.3GHz) - RAM: DDR4 512M - Flash: eMMC 8G, MicroSD card slot - WiFi: 2.4GHz and 5GHz with 6 antennas - Ethernet: - 1x LAN (10/100/1000M) - 1x WAN (10/100/1000/2500M) - 5G: Quectel RM520N-GL with two nano-SIM card slots - USB: 1x USB 2.0 port - UART: - 3.3V, TX, RX, GND / 115200 8N1 MAC addresses as verified by OEM firmware: vendor OpenWrt address source WAN eth0 label factory 0x0a (label) LAN eth1 label + 1 2g phy0-ap0 label + 2 factory 0x04 5g phy1-ap0 label + 3 Installation via U-Boot rescue: 1. Press and hold reset button while booting the device 2. Wait for the Internet led to blink 5 times 3. Release reset button 4. The rescue page is accessible via http://192.168.1.1 5. Select the OpenWrt sysupgrade image and start upgrade 6. Wait for the router to flash new firmware and reboot Revert to stock firmware: 1. Download the stock firmware from GL.iNet website 2. Use the method explained above to flash the stock firmware Switch the modem network port between PCIe and USB interfaces: 1. Connect to the AT commands (/dev/ttyUSB2) port using e.g. minicom: minicom -D /dev/ttyUSB2 2. Check the current modem mode with 'AT+QCFG="data_interface"': - 0,0 indicates that the network port uses the USB interface - 1,0 indicates that the network port uses the PCIe interface 3. Switch the active interface with: - 'AT+QCFG="data_interface",0,0' to use the USB interface - 'AT+QCFG="data_interface",1,0' to use the PCIe interface 4. Reboot Signed-off-by: Jean Thomas <jean.thomas@wifirst.fr>
274 lines
4.6 KiB
Plaintext
274 lines
4.6 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
/dts-v1/;
|
|
|
|
#include "mt7981.dtsi"
|
|
|
|
/ {
|
|
chosen {
|
|
bootargs = "console=ttyS0,115200n8 root=PARTLABEL=rootfs rootwait";
|
|
};
|
|
|
|
aliases {
|
|
label-mac-device = &gmac0;
|
|
led-boot = &led_power;
|
|
led-failsafe = &led_power;
|
|
led-running = &led_power;
|
|
led-upgrade = &led_power;
|
|
};
|
|
|
|
reg_5v: regulator-5v {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "fixed-5V";
|
|
regulator-min-microvolt = <5000000>;
|
|
regulator-max-microvolt = <5000000>;
|
|
regulator-boot-on;
|
|
regulator-always-on;
|
|
};
|
|
|
|
fan_5v: regulator-fan-5v {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "fan";
|
|
regulator-min-microvolt = <5000000>;
|
|
regulator-max-microvolt = <5000000>;
|
|
gpio = <&pio 28 GPIO_ACTIVE_HIGH>;
|
|
enable-active-high;
|
|
};
|
|
|
|
gpio-keys {
|
|
compatible = "gpio-keys";
|
|
|
|
reset {
|
|
label = "reset";
|
|
linux,code = <KEY_RESTART>;
|
|
gpios = <&pio 1 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
gpio-export {
|
|
compatible = "gpio-export";
|
|
|
|
hub_power {
|
|
gpio-export,name = "hub_power";
|
|
gpio-export,output = <1>;
|
|
gpios = <&pio 5 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
5G_power {
|
|
gpio-export,name = "5G_power";
|
|
gpio-export,output = <1>;
|
|
gpios = <&pio 11 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
5G_control {
|
|
gpio-export,name = "5G_control";
|
|
gpio-export,output = <1>;
|
|
gpios = <&pio 9 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
5G_reset {
|
|
gpio-export,name = "5G_reset";
|
|
gpio-export,output = <0>;
|
|
gpios = <&pio 10 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
wifi2g {
|
|
label = "green:wifi2g";
|
|
gpios = <&pio 30 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
wifi5g {
|
|
label = "green:wifi5g";
|
|
gpios = <&pio 38 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
5g_led1 {
|
|
label = "green:5g:led1";
|
|
gpios = <&pio 6 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
5g_led2 {
|
|
label = "green:5g:led2";
|
|
gpios = <&pio 7 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
5g_led3 {
|
|
label = "green:5g:led3";
|
|
gpios = <&pio 8 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
5g_led4 {
|
|
label = "green:5g:led4";
|
|
gpios = <&pio 4 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
led_power: power {
|
|
label = "green:power";
|
|
gpios = <&pio 39 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
wan {
|
|
label = "green:wan";
|
|
gpios = <&pio 31 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&uart0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&watchdog {
|
|
status = "okay";
|
|
};
|
|
|
|
&mmc0 {
|
|
pinctrl-names = "default", "state_uhs";
|
|
pinctrl-0 = <&mmc0_pins_default>;
|
|
pinctrl-1 = <&mmc0_pins_uhs>;
|
|
bus-width = <8>;
|
|
max-frequency = <52000000>;
|
|
cap-mmc-highspeed;
|
|
vmmc-supply = <®_3p3v>;
|
|
non-removable;
|
|
status = "okay";
|
|
|
|
card@0 {
|
|
compatible = "mmc-card";
|
|
reg = <0>;
|
|
|
|
block {
|
|
compatible = "block-device";
|
|
partitions {
|
|
block-partition-env {
|
|
partname = "u-boot-env";
|
|
|
|
nvmem-layout {
|
|
compatible = "u-boot,env-layout";
|
|
};
|
|
};
|
|
|
|
block-partition-factory {
|
|
partname = "factory";
|
|
|
|
nvmem-layout {
|
|
compatible = "fixed-layout";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
eeprom_factory_0: eeprom@0 {
|
|
reg = <0x0 0x1000>;
|
|
};
|
|
|
|
macaddr_factory_a: macaddr@a {
|
|
compatible = "mac-base";
|
|
reg = <0xa 0x6>;
|
|
#nvmem-cell-cells = <1>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&mdio_bus {
|
|
reset-gpios = <&pio 14 GPIO_ACTIVE_LOW>;
|
|
reset-delay-us = <600>;
|
|
reset-post-delay-us = <20000>;
|
|
|
|
phy5: ethernet-phy@5 {
|
|
reg = <5>;
|
|
compatible = "ethernet-phy-ieee802.3-c45";
|
|
};
|
|
};
|
|
|
|
ð {
|
|
status = "okay";
|
|
|
|
gmac0: mac@0 {
|
|
compatible = "mediatek,eth-mac";
|
|
reg = <0>;
|
|
phy-mode = "2500base-x";
|
|
phy-handle = <&phy5>;
|
|
nvmem-cells = <&macaddr_factory_a 0>;
|
|
nvmem-cell-names = "mac-address";
|
|
};
|
|
|
|
gmac1: mac@1 {
|
|
compatible = "mediatek,eth-mac";
|
|
reg = <1>;
|
|
phy-mode = "gmii";
|
|
phy-handle = <&int_gbe_phy>;
|
|
nvmem-cells = <&macaddr_factory_a 1>;
|
|
nvmem-cell-names = "mac-address";
|
|
};
|
|
};
|
|
|
|
&pio {
|
|
mmc0_pins_default: mmc0-pins-default {
|
|
mux {
|
|
function = "flash";
|
|
groups = "emmc_8";
|
|
};
|
|
};
|
|
mmc0_pins_uhs: mmc0-pins-uhs {
|
|
mux {
|
|
function = "flash";
|
|
groups = "emmc_8";
|
|
};
|
|
};
|
|
pcie_pins: pcie-pins {
|
|
mux {
|
|
function = "pcie";
|
|
groups = "pcie_pereset", "pcie_clk", "pcie_wake";
|
|
};
|
|
};
|
|
pwm0_pin: pwm0-pin-g0 {
|
|
mux {
|
|
function = "pwm";
|
|
groups = "pwm0_1";
|
|
};
|
|
};
|
|
};
|
|
|
|
&xhci {
|
|
phys = <&u2port0 PHY_TYPE_USB2>;
|
|
vbus-supply = <®_5v>;
|
|
mediatek,u3p-dis-msk = <0x01>;
|
|
status = "okay";
|
|
};
|
|
|
|
&usb_phy {
|
|
status = "okay";
|
|
};
|
|
|
|
&pcie {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pcie_pins>;
|
|
status = "okay";
|
|
};
|
|
|
|
&pwm {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pwm0_pin>;
|
|
};
|
|
|
|
&wifi {
|
|
nvmem-cells = <&eeprom_factory_0>;
|
|
nvmem-cell-names = "eeprom";
|
|
status = "okay";
|
|
};
|
|
|
|
&fan {
|
|
pwms = <&pwm 0 40000 0>;
|
|
fan-supply = <&fan_5v>;
|
|
interrupt-parent = <&pio>;
|
|
interrupts = <29 IRQ_TYPE_EDGE_RISING>;
|
|
status = "okay";
|
|
};
|