mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-24 07:46:48 +00:00
ebc090e420
The introduction ofebf0d8dade("ath79: add new ar934x spi driver") made the SPI memory unusable on devices with very high spi-max-frequency (104 MHz). Here's how the actual clock is calculated: (AHB_CLK/((CLOCK_DIVIDER+1)*2)) where AHB_CLK is a fixed clock (e.g. 200MHz on AR9331) and CLOCK_DIVIDER is the parameter we can set. Highest clock according to this formula is AHB_CLK/2 (100MHz, but that didn't work in device tests). The next possible value is AHB_CLK/4 (50MHz). Speeds between 50 MHz and 100 MHz will be rounded down, so using values higher than 50 MHz does not provide any benefit. Consequently, this patch reduces spi-max-frequency for all devices with values higher than 50 MHz to 50 MHz (effectively, this only affects devices with 104 MHz before this patch). Tested on GL.inet GL-AR150: Boot fails with 104 MHz but is successful with both 50 MHz and 80 MHz (fast-read), where the latter two yield identical read speeds. Fixes:ebf0d8dade("ath79: add new ar934x spi driver") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
182 lines
2.9 KiB
Plaintext
182 lines
2.9 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0
|
|
/dts-v1/;
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
#include "ar9331.dtsi"
|
|
|
|
/ {
|
|
model = "TP-Link TL-MR3020 V1";
|
|
compatible = "tplink,tl-mr3020-v1", "qca,ar9331";
|
|
|
|
aliases {
|
|
serial0 = &uart;
|
|
led-boot = &led_wps;
|
|
led-failsafe = &led_wps;
|
|
led-running = &led_wps;
|
|
led-upgrade = &led_wps;
|
|
label-mac-device = ð0;
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
wlan {
|
|
label = "tp-link:green:wlan";
|
|
gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
|
|
linux,default-trigger = "phy0tpt";
|
|
};
|
|
|
|
lan {
|
|
label = "tp-link:green:lan";
|
|
gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
led_wps: wps {
|
|
label = "tp-link:green:wps";
|
|
gpios = <&gpio 26 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
led3g {
|
|
label = "tp-link:green:3g";
|
|
gpios = <&gpio 27 GPIO_ACTIVE_LOW>;
|
|
trigger-sources = <&hub_port>;
|
|
linux,default-trigger = "usbport";
|
|
};
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
reset {
|
|
label = "reset";
|
|
linux,code = <KEY_RESTART>;
|
|
gpios = <&gpio 11 GPIO_ACTIVE_HIGH>;
|
|
debounce-interval = <60>;
|
|
};
|
|
|
|
sw1 {
|
|
label = "sw1";
|
|
linux,input-type = <EV_SW>;
|
|
linux,code = <BTN_0>;
|
|
gpios = <&gpio 18 GPIO_ACTIVE_HIGH>;
|
|
debounce-interval = <60>;
|
|
};
|
|
|
|
sw2 {
|
|
label = "sw2";
|
|
linux,input-type = <EV_SW>;
|
|
linux,code = <BTN_1>;
|
|
gpios = <&gpio 20 GPIO_ACTIVE_HIGH>;
|
|
debounce-interval = <60>;
|
|
};
|
|
};
|
|
|
|
reg_usb_vbus: reg_usb_vbus {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "usb_vbus";
|
|
regulator-min-microvolt = <5000000>;
|
|
regulator-max-microvolt = <5000000>;
|
|
gpio = <&gpio 8 GPIO_ACTIVE_HIGH>;
|
|
enable-active-high;
|
|
};
|
|
};
|
|
|
|
&ref {
|
|
clock-frequency = <25000000>;
|
|
};
|
|
|
|
&uart {
|
|
status = "okay";
|
|
};
|
|
|
|
&gpio {
|
|
status = "okay";
|
|
};
|
|
|
|
&usb {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
dr_mode = "host";
|
|
vbus-supply = <®_usb_vbus>;
|
|
status = "okay";
|
|
|
|
hub_port: port@1 {
|
|
reg = <1>;
|
|
#trigger-source-cells = <0>;
|
|
};
|
|
};
|
|
|
|
&usb_phy {
|
|
status = "okay";
|
|
};
|
|
|
|
&spi {
|
|
status = "okay";
|
|
|
|
num-chipselects = <1>;
|
|
|
|
/* Spansion S25FL032PIF SPI flash */
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
spi-max-frequency = <50000000>;
|
|
reg = <0>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
uboot: partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x000000 0x020000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@20000 {
|
|
compatible = "tplink,firmware";
|
|
label = "firmware";
|
|
reg = <0x020000 0x3c0000>;
|
|
};
|
|
|
|
partition@3e0000 {
|
|
label = "config";
|
|
reg = <0x3e0000 0x010000>;
|
|
read-only;
|
|
};
|
|
|
|
art: partition@3f0000 {
|
|
label = "art";
|
|
reg = <0x3f0000 0x010000>;
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
|
|
mtd-mac-address = <&uboot 0x1fc00>;
|
|
gmac-config {
|
|
device = <&gmac>;
|
|
|
|
switch-phy-addr-swap = <0>;
|
|
switch-phy-swap = <0>;
|
|
};
|
|
};
|
|
|
|
ð1 {
|
|
status = "okay";
|
|
|
|
compatible = "syscon", "simple-mfd";
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
|
|
mtd-cal-data = <&art 0x1000>;
|
|
mtd-mac-address = <&uboot 0x1fc00>;
|
|
};
|