openwrt/target/linux/ath79/image
Sven Eckelmann eb3a5ddba0 ath79: Add support for OpenMesh OM2P-LC
Device specifications:
======================

* Qualcomm/Atheros AR9330 rev 1
* 400/400/200 MHz (CPU/DDR/AHB)
* 64 MB of RAM
* 16 MB of SPI NOR flash
  - 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2x 10/100 Mbps Ethernet
* 1T1R 2.4 GHz Wi-Fi
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x fast ethernet
  - eth0
    + builtin switch port 1
    + used as LAN interface
  - eth1
    + 18-24V passive POE (mode B)
    + used as WAN interface
* 12-24V 1A DC
* internal antennas

Flashing instructions:
======================

Various methods can be used to install the actual image on the flash.
Two easy ones are:

ap51-flash
----------

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.

initramfs from TFTP
-------------------

The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):

   setenv serverip 192.168.1.21
   setenv ipaddr 192.168.1.1
   tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr

The actual sysupgrade image can then be transferred (on the LAN port) to
the device via

  scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/

On the device, the sysupgrade must then be started using

  sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin

Signed-off-by: Sven Eckelmann <sven@narfation.org>
2020-12-30 23:32:07 +01:00
..
bin ath79: add support for PISEN WMB001N 2019-08-08 21:00:59 +08:00
lzma-loader ath79: move lzma-loader to the end of available RAM 2020-01-23 15:28:03 +01:00
common-buffalo.mk ath79: use common device definition for Buffalo devices 2020-09-16 17:31:03 +02:00
common-mikrotik.mk ath79/mikrotik: disable building NAND images 2020-12-27 20:33:57 +01:00
common-netgear.mk ath79: netgear: trim down uImage customisations 2020-11-25 16:33:49 +01:00
common-tp-link.mk ath79: replace custom uImageArcher generation 2020-06-29 01:08:09 +02:00
common-yuncore.mk ath79: add support for YunCore TFTP image generation 2019-11-25 17:32:46 +01:00
generic-tp-link.mk ath79: add support for TP-Link TL-WDR7500 v3 2020-12-04 18:21:08 +01:00
generic-ubnt.mk ath79: add support for Ubiquiti airCube AC 2020-12-22 19:11:50 +01:00
generic.mk ath79: Add support for OpenMesh OM2P-LC 2020-12-30 23:32:07 +01:00
Makefile ath79: restore sysupgrade support for ja76pf2 and routerstations 2020-12-01 20:03:15 +01:00
mikrotik.mk ath79: add support for MikroTik RouterBOARD wAPR-2nD (wAP R) 2020-12-22 19:11:50 +01:00
nand.mk ath79: netgear: trim down uImage customisations 2020-11-25 16:33:49 +01:00
tiny-netgear.mk ath79: netgear: trim down uImage customisations 2020-11-25 16:33:49 +01:00
tiny-tp-link.mk ath79: add support for TP-Link TL-WA901ND v3 2020-08-08 20:40:48 +02:00
tiny.mk ath79: use common device definition for Buffalo devices 2020-09-16 17:31:03 +02:00