mirror of
https://github.com/openwrt/openwrt.git
synced 2025-01-11 07:22:54 +00:00
ea5bb6bbfe
Device specifications:
* QCA IPQ4018
* 256 MB of RAM
* 32 MB of SPI NOR flash (w25q256)
- 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=PlasmaCloud-PA1200
* 2T2R 5 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=PlasmaCloud-PA1200
* 3x GPIO-LEDs for status (cyan, purple, yellow)
* 1x GPIO-button (reset)
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
- phy@mdio4:
+ Label: Ethernet 1
+ gmac0 (ethaddr) in original firmware
+ used as LAN interface
- phy@mdio3:
+ Label: Ethernet 2
+ gmac1 (eth1addr) in original firmware
+ 802.3af/at POE(+)
+ used as WAN interface
* 12V/24V 1A DC
Flashing instructions:
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.
Signed-off-by: Marek Lindner <marek.lindner@kaiwoo.ai>
[sven@narfation.org: prepare commit message, rebase, use all LEDs, switch
to dualboot_datachk upgrade script, use eth1 as designated WAN interface]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
|
||
|---|---|---|
| .. | ||
| 100-GPIO-add-named-gpio-exports.patch | ||
| 101-arm-dts-IPQ4019-add-SDHCI-VQMMC-LDO-node.patch | ||
| 102-ARM-dts-qcom-ipq4019-add-USB-devicetree-nodes.patch | ||
| 103-arm-dts-qcom-ipq4019-add-more-labels.patch | ||
| 104-clk-fix-apss-cpu-overclocking.patch | ||
| 300-clk-qcom-ipq4019-add-ess-reset.patch | ||
| 400-mmc-sdhci-sdhci-msm-use-sdhci_set_clock-instead-of-s.patch | ||
| 700-net-add-qualcomm-mdio.patch | ||
| 702-dts-ipq4019-add-PHY-switch-nodes.patch | ||
| 703-net-IPQ4019-needs-rfs-vlan_tag-callbacks-in.patch | ||
| 705-net-add-qualcomm-ar40xx-phy.patch | ||
| 710-net-add-qualcomm-essedma-ethernet-driver.patch | ||
| 711-dts-ipq4019-add-ethernet-essedma-node.patch | ||
| 850-soc-add-qualcomm-syscon.patch | ||
| 900-dts-ipq4019-ap-dk01.1.patch | ||
| 901-arm-boot-add-dts-files.patch | ||
| 902-dts-ipq4019-ap-dk04.1.patch | ||
| 997-device_tree_cmdline.patch | ||
| 0001-v5.7-ARM-qcom-Add-support-for-IPQ40xx.patch | ||
| 0002-01-v5.6-regulator-add-IPQ4019-SDHCI-VQMMC-LDO-driver.patch | ||
| 0002-02-v5.5-ARM-dts-qcom-ipq4019-Add-SDHCI-controller-node.patch | ||
| 0003-v5.6-ARM-dts-qcom-Add-nodes-for-SMP-boot-in-IPQ40xx.patch | ||
| 0003-v5.7-ARM-dts-qcom-add-gpio-ranges-property.patch | ||
| 0004-v5.8-ARM-dts-qcom-ipq4019-fix-high-resolution-timer.patch | ||
| 0005-v5.8-02-ARM-dts-qcom-ipq4019-add-MDIO-node.patch | ||
| 0006-v5.5-crypto-qce-add-CRYPTO_ALG_KERN_DRIVER_ONLY-flag.patch | ||
| 0007-v5.5-crypto-qce-switch-to-skcipher-API.patch | ||
| 0008-v5.6-crypto-qce-fix-ctr-aes-qce-block-chunk-sizes.patch | ||
| 0009-v5.6-crypto-qce-fix-xts-aes-qce-key-sizes.patch | ||
| 0010-v5.6-crypto-qce-save-a-sg-table-slot-for-result-buf.patch | ||
| 0011-v5.6-crypto-qce-update-the-skcipher-IV.patch | ||
| 0012-v5.6-crypto-qce-initialize-fallback-only-for-AES.patch | ||
| 0013-v5.6-crypto-qce-allow-building-only-hashes-ciphers.patch | ||
| 0014-v5.7-crypto-qce-use-cryptlen-when-adding-extra-sgl.patch | ||
| 0015-v5.7-crypto-qce-use-AES-fallback-for-small-requests.patch | ||
| 0016-v5.7-crypto-qce-handle-AES-XTS-cases-that-qce-fails.patch | ||
| 0017-v5.8-phy-add-driver-for-Qualcomm-IPQ40xx-USB-PHY.patch | ||
| 0018-v5.9-pinctrl-msm-open-drain.patch | ||
| 0019-v5.6-mtd-spi-nor-Add-support-for-mx25r3235f.patch | ||