mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-27 09:12:39 +00:00
ea5bb6bbfe
Device specifications:
* QCA IPQ4018
* 256 MB of RAM
* 32 MB of SPI NOR flash (w25q256)
- 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=PlasmaCloud-PA1200
* 2T2R 5 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=PlasmaCloud-PA1200
* 3x GPIO-LEDs for status (cyan, purple, yellow)
* 1x GPIO-button (reset)
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
- phy@mdio4:
+ Label: Ethernet 1
+ gmac0 (ethaddr) in original firmware
+ used as LAN interface
- phy@mdio3:
+ Label: Ethernet 2
+ gmac1 (eth1addr) in original firmware
+ 802.3af/at POE(+)
+ used as WAN interface
* 12V/24V 1A DC
Flashing instructions:
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.
Signed-off-by: Marek Lindner <marek.lindner@kaiwoo.ai>
[sven@narfation.org: prepare commit message, rebase, use all LEDs, switch
to dualboot_datachk upgrade script, use eth1 as designated WAN interface]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
127 lines
2.5 KiB
Bash
127 lines
2.5 KiB
Bash
PART_NAME=firmware
|
|
REQUIRE_IMAGE_METADATA=1
|
|
|
|
RAMFS_COPY_BIN='fw_printenv fw_setenv'
|
|
RAMFS_COPY_DATA='/etc/fw_env.config /var/lock/fw_printenv.lock'
|
|
|
|
platform_check_image() {
|
|
case "$(board_name)" in
|
|
asus,rt-ac58u)
|
|
CI_UBIPART="UBI_DEV"
|
|
local ubidev=$(nand_find_ubi $CI_UBIPART)
|
|
local asus_root=$(nand_find_volume $ubidev jffs2)
|
|
|
|
[ -n "$asus_root" ] || return 0
|
|
|
|
cat << EOF
|
|
jffs2 partition is still present.
|
|
There's probably no space left
|
|
to install the filesystem.
|
|
|
|
You need to delete the jffs2 partition first:
|
|
# ubirmvol /dev/ubi0 --name=jffs2
|
|
|
|
Once this is done. Retry.
|
|
EOF
|
|
return 1
|
|
;;
|
|
esac
|
|
return 0;
|
|
}
|
|
|
|
askey_do_upgrade() {
|
|
local tar_file="$1"
|
|
|
|
local board_dir=$(tar tf $tar_file | grep -m 1 '^sysupgrade-.*/$')
|
|
board_dir=${board_dir%/}
|
|
|
|
tar Oxf $tar_file ${board_dir}/root | mtd write - rootfs
|
|
|
|
nand_do_upgrade "$1"
|
|
}
|
|
|
|
zyxel_do_upgrade() {
|
|
local tar_file="$1"
|
|
|
|
local board_dir=$(tar tf $tar_file | grep -m 1 '^sysupgrade-.*/$')
|
|
board_dir=${board_dir%/}
|
|
|
|
tar Oxf $tar_file ${board_dir}/kernel | mtd write - kernel
|
|
|
|
if [ -n "$UPGRADE_BACKUP" ]; then
|
|
tar Oxf $tar_file ${board_dir}/root | mtd -j "$UPGRADE_BACKUP" write - rootfs
|
|
else
|
|
tar Oxf $tar_file ${board_dir}/root | mtd write - rootfs
|
|
fi
|
|
}
|
|
|
|
platform_do_upgrade() {
|
|
case "$(board_name)" in
|
|
8dev,jalapeno |\
|
|
aruba,ap-303 |\
|
|
aruba,ap-303h |\
|
|
aruba,ap-365 |\
|
|
avm,fritzbox-7530 |\
|
|
avm,fritzrepeater-1200 |\
|
|
avm,fritzrepeater-3000 |\
|
|
buffalo,wtr-m2133hp |\
|
|
cilab,meshpoint-one |\
|
|
edgecore,ecw5211 |\
|
|
edgecore,oap100 |\
|
|
engenius,eap2200 |\
|
|
luma,wrtq-329acn |\
|
|
mobipromo,cm520-79f |\
|
|
qxwlan,e2600ac-c2)
|
|
nand_do_upgrade "$1"
|
|
;;
|
|
alfa-network,ap120c-ac)
|
|
part="$(awk -F 'ubi.mtd=' '{printf $2}' /proc/cmdline | sed -e 's/ .*$//')"
|
|
if [ "$part" = "rootfs1" ]; then
|
|
fw_setenv active 2 || exit 1
|
|
CI_UBIPART="rootfs2"
|
|
else
|
|
fw_setenv active 1 || exit 1
|
|
CI_UBIPART="rootfs1"
|
|
fi
|
|
nand_do_upgrade "$1"
|
|
;;
|
|
asus,map-ac2200)
|
|
CI_KERNPART="linux"
|
|
nand_do_upgrade "$1"
|
|
;;
|
|
asus,rt-ac58u)
|
|
CI_UBIPART="UBI_DEV"
|
|
CI_KERNPART="linux"
|
|
nand_do_upgrade "$1"
|
|
;;
|
|
cellc,rtl30vw)
|
|
CI_UBIPART="ubifs"
|
|
askey_do_upgrade "$1"
|
|
;;
|
|
compex,wpj419)
|
|
nand_do_upgrade "$1"
|
|
;;
|
|
linksys,ea6350v3 |\
|
|
linksys,ea8300 |\
|
|
linksys,mr8300)
|
|
platform_do_upgrade_linksys "$1"
|
|
;;
|
|
meraki,mr33)
|
|
CI_KERNPART="part.safe"
|
|
nand_do_upgrade "$1"
|
|
;;
|
|
openmesh,a42 |\
|
|
openmesh,a62 |\
|
|
plasmacloud,pa1200)
|
|
PART_NAME="inactive"
|
|
platform_do_upgrade_dualboot_datachk "$1"
|
|
;;
|
|
zyxel,nbg6617)
|
|
zyxel_do_upgrade "$1"
|
|
;;
|
|
*)
|
|
default_do_upgrade "$1"
|
|
;;
|
|
esac
|
|
}
|