ExternalVendorCode/openwrt
1
0
Fork 0
mirror of https://github.com/openwrt/openwrt.git synced 2024-12-29 10:08:59 +00:00
Code Issues Actions 6 Packages Projects Releases Wiki Activity
e92a14709d
openwrt/target/linux/ar71xx/files/arch/mips/ath79/mach-ubnt-xm.c
Petr Štetiar 0f8cdc28af ar71xx: Add support for Ubiquity Bullet M (XW) 
CPU: AR9342 SoC
RAM:     64 MB DDR2
Flash:    8 MB NOR SPI
Ports:  100 MBit (24V PoE in)
WLAN: 2.4/5 GHz
UART:     1 UART on PCB marked as J1 with 115200 8N1 config
LEDs:       Power, Ethernet, 4x RSSI LEDs (orange, red, 2x green)
Buttons:    Reset

UART connection details

  .---------------------------------.
  |                                 |
[ETH]          J1                 [ANT]
  |    o VCC o RX o TX o GND        |
  `---------------------------------'

Flashing instructions using recovery method over TFTP

 1. Unplug the ethernet cable from the router.
 2. Using paper clip press and hold the router's reset button. Make sure
    you can feel it depressed by the paper clip. Do not release the button
    until step 4.
 3. While keeping the reset button pressed in, plug the ethernet cable
    back into the AP. Keep the reset button depressed until you see the
    device's LEDs flashing in upgrade mode (alternating LED1/LED3 and
    LED2/LED4), this may take up to 25 seconds.
 4. You may release the reset button, now the device should be in TFTP
    transfer mode.
 5. Set a static IP on your Computer's NIC. A static IP of 192.168.1.25/24
    should work.
 6. Plug the PoE injector's LAN cable directly to your computer.
 7. Start tftp client and issue following commands:
     tftp> binary
     tftp> connect 192.168.1.20
     tftp> put openwrt-ar71xx-generic-ubnt-bullet-m-xw-squashfs-factory.bin

Tested only on Bullet M2HP.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-04-08 18:37:04 +02:00

782 lines
21 KiB
C
Raw Blame History

/*
* Ubiquiti Networks XM (rev 1.0) board support
*
* Copyright (C) 2011 René Bolldorf <xsecute@googlemail.com>
*
* Derived from: mach-pb44.c
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License version 2 as published
* by the Free Software Foundation.
*/
#include <linux/init.h>
#include <linux/pci.h>
#include <linux/gpio.h>
#include <linux/platform_device.h>
#include <linux/ath9k_platform.h>
#include <linux/etherdevice.h>
#include <linux/ar8216_platform.h>
#include <linux/platform_data/phy-at803x.h>
#include <asm/mach-ath79/ath79.h>
#include <asm/mach-ath79/irq.h>
#include <asm/mach-ath79/ar71xx_regs.h>
#include <linux/platform_data/phy-at803x.h>
#include "common.h"
#include "dev-ap9x-pci.h"
#include "dev-eth.h"
#include "dev-gpio-buttons.h"
#include "dev-leds-gpio.h"
#include "dev-m25p80.h"
#include "dev-usb.h"
#include "dev-wmac.h"
#include "machtypes.h"
#define UBNT_XM_GPIO_LED_L1 0
#define UBNT_XM_GPIO_LED_L2 1
#define UBNT_XM_GPIO_LED_L3 11
#define UBNT_XM_GPIO_LED_L4 7
#define UBNT_XM_GPIO_BTN_RESET 12
#define UBNT_XM_KEYS_POLL_INTERVAL 20
#define UBNT_XM_KEYS_DEBOUNCE_INTERVAL (3 * UBNT_XM_KEYS_POLL_INTERVAL)
#define UBNT_XM_EEPROM_ADDR 0x1fff1000
static struct gpio_led ubnt_xm_leds_gpio[] __initdata = {
{
.name = "ubnt:red:link1",
.gpio = UBNT_XM_GPIO_LED_L1,
.active_low = 0,
}, {
.name = "ubnt:orange:link2",
.gpio = UBNT_XM_GPIO_LED_L2,
.active_low = 0,
}, {
.name = "ubnt:green:link3",
.gpio = UBNT_XM_GPIO_LED_L3,
.active_low = 0,
}, {
.name = "ubnt:green:link4",
.gpio = UBNT_XM_GPIO_LED_L4,
.active_low = 0,
},
};
static struct gpio_keys_button ubnt_xm_gpio_keys[] __initdata = {
{
.desc = "reset",
.type = EV_KEY,
.code = KEY_RESTART,
.debounce_interval = UBNT_XM_KEYS_DEBOUNCE_INTERVAL,
.gpio = UBNT_XM_GPIO_BTN_RESET,
.active_low = 1,
}
};
#define UBNT_M_WAN_PHYMASK BIT(4)
static void __init ubnt_xm_init(void)
{
u8 *eeprom = (u8 *) KSEG1ADDR(UBNT_XM_EEPROM_ADDR);
u8 *mac1 = (u8 *) KSEG1ADDR(0x1fff0000);
u8 *mac2 = (u8 *) KSEG1ADDR(0x1fff0000 + ETH_ALEN);
ath79_register_leds_gpio(-1, ARRAY_SIZE(ubnt_xm_leds_gpio),
ubnt_xm_leds_gpio);
ath79_register_gpio_keys_polled(-1, UBNT_XM_KEYS_POLL_INTERVAL,
ARRAY_SIZE(ubnt_xm_gpio_keys),
ubnt_xm_gpio_keys);
ath79_register_m25p80(NULL);
ap91_pci_init(eeprom, NULL);
ath79_register_mdio(0, ~UBNT_M_WAN_PHYMASK);
ath79_eth0_data.speed = SPEED_100;
ath79_init_mac(ath79_eth0_data.mac_addr, mac1, 0);
ath79_eth1_data.speed = SPEED_100;
ath79_init_mac(ath79_eth1_data.mac_addr, mac2, 0);
ath79_register_eth(0);
}
MIPS_MACHINE(ATH79_MACH_UBNT_XM,
"UBNT-XM",
"Ubiquiti Networks XM (rev 1.0) board",
ubnt_xm_init);
MIPS_MACHINE(ATH79_MACH_UBNT_BULLET_M, "UBNT-BM", "Ubiquiti Bullet M",
ubnt_xm_init);
static void __init ubnt_rocket_m_setup(void)
{
ubnt_xm_init();
ath79_register_usb();
}
MIPS_MACHINE(ATH79_MACH_UBNT_ROCKET_M, "UBNT-RM", "Ubiquiti Rocket M",
ubnt_rocket_m_setup);
static void __init ubnt_nano_m_setup(void)
{
ubnt_xm_init();
ath79_register_eth(1);
}
MIPS_MACHINE(ATH79_MACH_UBNT_NANO_M, "UBNT-NM", "Ubiquiti Nanostation M",
ubnt_nano_m_setup);
static struct gpio_led ubnt_airrouter_leds_gpio[] __initdata = {
{
.name = "ubnt:green:globe",
.gpio = 0,
.active_low = 1,
}, {
.name = "ubnt:green:power",
.gpio = 11,
.active_low = 1,
.default_state = LEDS_GPIO_DEFSTATE_ON,
}
};
static void __init ubnt_airrouter_setup(void)
{
u8 *mac1 = (u8 *) KSEG1ADDR(0x1fff0000);
u8 *ee = (u8 *) KSEG1ADDR(0x1fff1000);
ath79_register_m25p80(NULL);
ath79_register_mdio(0, ~UBNT_M_WAN_PHYMASK);
ath79_init_mac(ath79_eth0_data.mac_addr, mac1, 0);
ath79_init_local_mac(ath79_eth1_data.mac_addr, mac1);
ath79_register_eth(1);
ath79_register_eth(0);
ath79_register_usb();
ap91_pci_init(ee, NULL);
ath79_register_leds_gpio(-1, ARRAY_SIZE(ubnt_airrouter_leds_gpio),
ubnt_airrouter_leds_gpio);
ath79_register_gpio_keys_polled(-1, UBNT_XM_KEYS_POLL_INTERVAL,
ARRAY_SIZE(ubnt_xm_gpio_keys),
ubnt_xm_gpio_keys);
}
MIPS_MACHINE(ATH79_MACH_UBNT_AIRROUTER, "UBNT-AR", "Ubiquiti AirRouter",
ubnt_airrouter_setup);
static struct gpio_led ubnt_unifi_leds_gpio[] __initdata = {
{
.name = "ubnt:orange:dome",
.gpio = 1,
.active_low = 0,
}, {
.name = "ubnt:green:dome",
.gpio = 0,
.active_low = 0,
}
};
static struct gpio_led ubnt_unifi_outdoor_leds_gpio[] __initdata = {
{
.name = "ubnt:orange:front",
.gpio = 1,
.active_low = 0,
}, {
.name = "ubnt:green:front",
.gpio = 0,
.active_low = 0,
}
};
static struct gpio_led ubnt_unifi_outdoor_plus_leds_gpio[] __initdata = {
{
.name = "ubnt:white:front",
.gpio = 1,
.active_low = 0,
}, {
.name = "ubnt:blue:front",
.gpio = 0,
.active_low = 0,
}
};
static void __init ubnt_unifi_setup(void)
{
u8 *mac = (u8 *) KSEG1ADDR(0x1fff0000);
u8 *ee = (u8 *) KSEG1ADDR(0x1fff1000);
ath79_register_m25p80(NULL);
ath79_register_mdio(0, ~UBNT_M_WAN_PHYMASK);
ath79_init_mac(ath79_eth0_data.mac_addr, mac, 0);
ath79_register_eth(0);
ap91_pci_init(ee, NULL);
ath79_register_leds_gpio(-1, ARRAY_SIZE(ubnt_unifi_leds_gpio),
ubnt_unifi_leds_gpio);
ath79_register_gpio_keys_polled(-1, UBNT_XM_KEYS_POLL_INTERVAL,
ARRAY_SIZE(ubnt_xm_gpio_keys),
ubnt_xm_gpio_keys);
}
MIPS_MACHINE(ATH79_MACH_UBNT_UNIFI, "UBNT-UF", "Ubiquiti UniFi",
ubnt_unifi_setup);
#define UBNT_UNIFIOD_PRI_PHYMASK BIT(4)
#define UBNT_UNIFIOD_2ND_PHYMASK (BIT(0) | BIT(1) | BIT(2) | BIT(3))
static void __init ubnt_unifi_outdoor_setup(void)
{
u8 *mac1 = (u8 *) KSEG1ADDR(0x1fff0000);
u8 *mac2 = (u8 *) KSEG1ADDR(0x1fff0000 + ETH_ALEN);
u8 *ee = (u8 *) KSEG1ADDR(0x1fff1000);
ath79_register_m25p80(NULL);
ath79_register_mdio(0, ~(UBNT_UNIFIOD_PRI_PHYMASK |
UBNT_UNIFIOD_2ND_PHYMASK));
ath79_init_mac(ath79_eth0_data.mac_addr, mac1, 0);
ath79_init_mac(ath79_eth1_data.mac_addr, mac2, 0);
ath79_register_eth(0);
ath79_register_eth(1);
ap91_pci_init(ee, NULL);
ath79_register_leds_gpio(-1, ARRAY_SIZE(ubnt_unifi_outdoor_leds_gpio),
ubnt_unifi_outdoor_leds_gpio);
ath79_register_gpio_keys_polled(-1, UBNT_XM_KEYS_POLL_INTERVAL,
ARRAY_SIZE(ubnt_xm_gpio_keys),
ubnt_xm_gpio_keys);
}
MIPS_MACHINE(ATH79_MACH_UBNT_UNIFI_OUTDOOR, "UBNT-U20",
"Ubiquiti UniFiAP Outdoor",
ubnt_unifi_outdoor_setup);
static void __init ubnt_unifi_outdoor_plus_setup(void)
{
u8 *mac1 = (u8 *) KSEG1ADDR(0x1fff0000);
u8 *mac2 = (u8 *) KSEG1ADDR(0x1fff0000 + ETH_ALEN);
u8 *ee = (u8 *) KSEG1ADDR(0x1fff1000);
ath79_register_m25p80(NULL);
ath79_register_mdio(0, ~(UBNT_UNIFIOD_PRI_PHYMASK |
UBNT_UNIFIOD_2ND_PHYMASK));
ath79_init_mac(ath79_eth0_data.mac_addr, mac1, 0);
ath79_init_mac(ath79_eth1_data.mac_addr, mac2, 0);
ath79_register_eth(0);
ath79_register_eth(1);
ap9x_pci_get_wmac_data(0)->ubnt_hsr = true;
ap91_pci_init(ee, NULL);
ath79_register_leds_gpio(-1, ARRAY_SIZE(ubnt_unifi_outdoor_plus_leds_gpio),
ubnt_unifi_outdoor_plus_leds_gpio);
ath79_register_gpio_keys_polled(-1, UBNT_XM_KEYS_POLL_INTERVAL,
ARRAY_SIZE(ubnt_xm_gpio_keys),
ubnt_xm_gpio_keys);
}
MIPS_MACHINE(ATH79_MACH_UBNT_UNIFI_OUTDOOR_PLUS, "UBNT-UOP",
"Ubiquiti UniFiAP Outdoor+",
ubnt_unifi_outdoor_plus_setup);
static struct gpio_led ubnt_uap_pro_gpio_leds[] __initdata = {
{
.name = "ubnt:white:dome",
.gpio = 12,
}, {
.name = "ubnt:blue:dome",
.gpio = 13,
}
};
static struct gpio_keys_button uap_pro_gpio_keys[] __initdata = {
{
.desc = "reset",
.type = EV_KEY,
.code = KEY_RESTART,
.debounce_interval = UBNT_XM_KEYS_DEBOUNCE_INTERVAL,
.gpio = 17,
.active_low = 1,
}
};
static struct ar8327_pad_cfg uap_pro_ar8327_pad0_cfg = {
.mode = AR8327_PAD_MAC_RGMII,
.txclk_delay_en = true,
.rxclk_delay_en = true,
.txclk_delay_sel = AR8327_CLK_DELAY_SEL1,
.rxclk_delay_sel = AR8327_CLK_DELAY_SEL2,
};
static struct ar8327_platform_data uap_pro_ar8327_data = {
.pad0_cfg = &uap_pro_ar8327_pad0_cfg,
.port0_cfg = {
.force_link = 1,
.speed = AR8327_PORT_SPEED_1000,
.duplex = 1,
.txpause = 1,
.rxpause = 1,
},
};
static struct mdio_board_info uap_pro_mdio0_info[] = {
{
.bus_id = "ag71xx-mdio.0",
.mdio_addr = 0,
.platform_data = &uap_pro_ar8327_data,
},
};
#define UAP_PRO_MAC0_OFFSET 0x0000
#define UAP_PRO_MAC1_OFFSET 0x0006
#define UAP_PRO_WMAC_CALDATA_OFFSET 0x1000
#define UAP_PRO_PCI_CALDATA_OFFSET 0x5000
static void __init ubnt_uap_pro_setup(void)
{
u8 *eeprom = (u8 *) KSEG1ADDR(0x1fff0000);
ath79_register_m25p80(NULL);
ath79_register_leds_gpio(-1, ARRAY_SIZE(ubnt_uap_pro_gpio_leds),
ubnt_uap_pro_gpio_leds);
ath79_register_gpio_keys_polled(-1, UBNT_XM_KEYS_POLL_INTERVAL,
ARRAY_SIZE(uap_pro_gpio_keys),
uap_pro_gpio_keys);
ath79_register_wmac(eeprom + UAP_PRO_WMAC_CALDATA_OFFSET, NULL);
ap91_pci_init(eeprom + UAP_PRO_PCI_CALDATA_OFFSET, NULL);
ath79_register_mdio(0, 0x0);
mdiobus_register_board_info(uap_pro_mdio0_info,
ARRAY_SIZE(uap_pro_mdio0_info));
ath79_setup_ar934x_eth_cfg(AR934X_ETH_CFG_RGMII_GMAC0);
ath79_init_mac(ath79_eth0_data.mac_addr,
eeprom + UAP_PRO_MAC0_OFFSET, 0);
/* GMAC0 is connected to an AR8327 switch */
ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_RGMII;
ath79_eth0_data.phy_mask = BIT(0);
ath79_eth0_data.mii_bus_dev = &ath79_mdio0_device.dev;
ath79_eth0_pll_data.pll_1000 = 0x06000000;
ath79_register_eth(0);
}
MIPS_MACHINE(ATH79_MACH_UBNT_UAP_PRO, "UAP-PRO", "Ubiquiti UniFi AP Pro",
ubnt_uap_pro_setup);
#define UBNT_XW_GPIO_LED_L1 11
#define UBNT_XW_GPIO_LED_L2 16
#define UBNT_XW_GPIO_LED_L3 13
#define UBNT_XW_GPIO_LED_L4 14
static struct gpio_led ubnt_xw_leds_gpio[] __initdata = {
{
.name = "ubnt:red:link1",
.gpio = UBNT_XW_GPIO_LED_L1,
.active_low = 1,
}, {
.name = "ubnt:orange:link2",
.gpio = UBNT_XW_GPIO_LED_L2,
.active_low = 1,
}, {
.name = "ubnt:green:link3",
.gpio = UBNT_XW_GPIO_LED_L3,
.active_low = 1,
}, {
.name = "ubnt:green:link4",
.gpio = UBNT_XW_GPIO_LED_L4,
.active_low = 1,
},
};
#define UBNT_ROCKET_TI_GPIO_LED_L1 16
#define UBNT_ROCKET_TI_GPIO_LED_L2 17
#define UBNT_ROCKET_TI_GPIO_LED_L3 18
#define UBNT_ROCKET_TI_GPIO_LED_L4 19
#define UBNT_ROCKET_TI_GPIO_LED_L5 20
#define UBNT_ROCKET_TI_GPIO_LED_L6 21
static struct gpio_led ubnt_rocket_ti_leds_gpio[] __initdata = {
{
.name = "ubnt:green:link1",
.gpio = UBNT_ROCKET_TI_GPIO_LED_L1,
.active_low = 1,
}, {
.name = "ubnt:green:link2",
.gpio = UBNT_ROCKET_TI_GPIO_LED_L2,
.active_low = 1,
}, {
.name = "ubnt:green:link3",
.gpio = UBNT_ROCKET_TI_GPIO_LED_L3,
.active_low = 1,
}, {
.name = "ubnt:green:link4",
.gpio = UBNT_ROCKET_TI_GPIO_LED_L4,
.active_low = 0,
}, {
.name = "ubnt:green:link5",
.gpio = UBNT_ROCKET_TI_GPIO_LED_L5,
.active_low = 0,
}, {
.name = "ubnt:green:link6",
.gpio = UBNT_ROCKET_TI_GPIO_LED_L6,
.active_low = 0,
},
};
static void __init ubnt_xw_init(void)
{
u8 *eeprom = (u8 *) KSEG1ADDR(0x1fff0000);
ath79_register_m25p80(NULL);
ath79_register_leds_gpio(-1, ARRAY_SIZE(ubnt_xw_leds_gpio),
ubnt_xw_leds_gpio);
ath79_register_gpio_keys_polled(-1, UBNT_XM_KEYS_POLL_INTERVAL,
ARRAY_SIZE(ubnt_xm_gpio_keys),
ubnt_xm_gpio_keys);
ath79_register_wmac(eeprom + UAP_PRO_WMAC_CALDATA_OFFSET, NULL);
ap91_pci_init(eeprom + UAP_PRO_PCI_CALDATA_OFFSET, NULL);
ath79_setup_ar934x_eth_cfg(AR934X_ETH_CFG_MII_GMAC0 | AR934X_ETH_CFG_MII_GMAC0_SLAVE);
ath79_init_mac(ath79_eth0_data.mac_addr,
eeprom + UAP_PRO_MAC0_OFFSET, 0);
ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_MII;
ath79_eth0_data.mii_bus_dev = &ath79_mdio0_device.dev;
}
static void __init ubnt_nano_m_xw_setup(void)
{
ubnt_xw_init();
/* GMAC0 is connected to an AR8326 switch */
ath79_register_mdio(0, ~(BIT(0) | BIT(1) | BIT(5)));
ath79_eth0_data.phy_mask = (BIT(0) | BIT(1) | BIT(5));
ath79_eth0_data.speed = SPEED_100;
ath79_eth0_data.duplex = DUPLEX_FULL;
ath79_register_eth(0);
}
static struct at803x_platform_data ubnt_loco_m_xw_at803x_data = {
.has_reset_gpio = 1,
.reset_gpio = 0,
};
static struct mdio_board_info ubnt_loco_m_xw_mdio_info[] = {
{
.bus_id = "ag71xx-mdio.0",
.mdio_addr = 1,
.platform_data = &ubnt_loco_m_xw_at803x_data,
},
};
static void __init ubnt_loco_m_xw_setup(void)
{
ubnt_xw_init();
mdiobus_register_board_info(ubnt_loco_m_xw_mdio_info,
ARRAY_SIZE(ubnt_loco_m_xw_mdio_info));
ath79_register_mdio(0, ~BIT(1));
ath79_eth0_data.phy_mask = BIT(1);
ath79_register_eth(0);
}
#define UBNT_LBE_M5_GPIO_LED_LAN 13
#define UBNT_LBE_M5_GPIO_LED_WLAN 14
#define UBNT_LBE_M5_GPIO_LED_SYS 16
static struct gpio_led ubnt_lbe_m5_leds_gpio[] __initdata = {
{
.name = "ubnt:green:lan",
.gpio = UBNT_LBE_M5_GPIO_LED_LAN,
.active_low = 1,
}, {
.name = "ubnt:green:wlan",
.gpio = UBNT_LBE_M5_GPIO_LED_WLAN,
.active_low = 1,
}, {
.name = "ubnt:green:sys",
.gpio = UBNT_LBE_M5_GPIO_LED_SYS,
.active_low = 1,
},
};
static void __init ubnt_lbe_m5_setup(void)
{
u8 *eeprom = (u8 *) KSEG1ADDR(0x1fff0000);
ath79_register_m25p80(NULL);
ath79_register_wmac(eeprom + UAP_PRO_WMAC_CALDATA_OFFSET, NULL);
ap91_pci_init(eeprom + UAP_PRO_PCI_CALDATA_OFFSET, NULL);
ath79_register_leds_gpio(-1, ARRAY_SIZE(ubnt_lbe_m5_leds_gpio),
ubnt_lbe_m5_leds_gpio);
ath79_register_gpio_keys_polled(-1, UBNT_XM_KEYS_POLL_INTERVAL,
ARRAY_SIZE(ubnt_xm_gpio_keys),
ubnt_xm_gpio_keys);
ath79_setup_ar934x_eth_cfg(AR934X_ETH_CFG_MII_GMAC0 |
AR934X_ETH_CFG_MII_GMAC0_SLAVE);
ath79_init_mac(ath79_eth0_data.mac_addr,
eeprom + UAP_PRO_MAC0_OFFSET, 0);
ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_MII;
ath79_eth0_data.mii_bus_dev = &ath79_mdio0_device.dev;
gpio_request_one(0, GPIOF_OUT_INIT_LOW | GPIOF_ACTIVE_LOW |
GPIOF_EXPORT_DIR_FIXED, "SPI nWP");
mdiobus_register_board_info(ubnt_loco_m_xw_mdio_info,
ARRAY_SIZE(ubnt_loco_m_xw_mdio_info));
ath79_register_mdio(0, ~BIT(1));
ath79_eth0_data.phy_mask = BIT(1);
ath79_register_eth(0);
}
static void __init ubnt_rocket_m_xw_setup(void)
{
u8 *eeprom = (u8 *) KSEG1ADDR(0x1fff0000);
ath79_register_m25p80(NULL);
ath79_register_leds_gpio(-1, ARRAY_SIZE(ubnt_xw_leds_gpio),
ubnt_xw_leds_gpio);
ath79_register_gpio_keys_polled(-1, UBNT_XM_KEYS_POLL_INTERVAL,
ARRAY_SIZE(ubnt_xm_gpio_keys),
ubnt_xm_gpio_keys);
ath79_register_wmac(eeprom + UAP_PRO_WMAC_CALDATA_OFFSET, NULL);
ap91_pci_init(eeprom + UAP_PRO_PCI_CALDATA_OFFSET, NULL);
ath79_setup_ar934x_eth_cfg(AR934X_ETH_CFG_RGMII_GMAC0);
ath79_init_mac(ath79_eth0_data.mac_addr,
eeprom + UAP_PRO_MAC0_OFFSET, 0);
ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_RGMII;
ath79_eth0_data.mii_bus_dev = &ath79_mdio0_device.dev;
ath79_register_mdio(0, ~BIT(4));
ath79_eth0_data.phy_mask = BIT(4);
ath79_eth0_pll_data.pll_1000 = 0x06000000;
ath79_register_eth(0);
}
static struct at803x_platform_data ubnt_rocket_m_ti_at803_data = {
.disable_smarteee = 1,
.enable_rgmii_rx_delay = 1,
.enable_rgmii_tx_delay = 1,
};
static struct mdio_board_info ubnt_rocket_m_ti_mdio_info[] = {
{
.bus_id = "ag71xx-mdio.0",
.mdio_addr = 4,
.platform_data = &ubnt_rocket_m_ti_at803_data,
},
};
static void __init ubnt_rocket_m_ti_setup(void)
{
u8 *eeprom = (u8 *) KSEG1ADDR(0x1fff0000);
ath79_register_m25p80(NULL);
ath79_register_leds_gpio(-1, ARRAY_SIZE(ubnt_rocket_ti_leds_gpio),
ubnt_rocket_ti_leds_gpio);
ath79_register_gpio_keys_polled(-1, UBNT_XM_KEYS_POLL_INTERVAL,
ARRAY_SIZE(ubnt_xm_gpio_keys),
ubnt_xm_gpio_keys);
ap91_pci_init(eeprom + 0x1000, NULL);
ath79_setup_ar934x_eth_cfg(AR934X_ETH_CFG_RGMII_GMAC0);
ath79_setup_ar934x_eth_rx_delay(3, 3);
ath79_init_mac(ath79_eth0_data.mac_addr,
eeprom + UAP_PRO_MAC0_OFFSET, 0);
ath79_init_mac(ath79_eth1_data.mac_addr,
eeprom + UAP_PRO_MAC1_OFFSET, 0);
ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_RGMII;
ath79_eth0_data.mii_bus_dev = &ath79_mdio0_device.dev;
ath79_eth1_data.phy_if_mode = PHY_INTERFACE_MODE_GMII;
ath79_eth1_data.mii_bus_dev = &ath79_mdio1_device.dev;
mdiobus_register_board_info(ubnt_rocket_m_ti_mdio_info,
ARRAY_SIZE(ubnt_rocket_m_ti_mdio_info));
ath79_register_mdio(0, 0x0);
ath79_eth0_data.phy_mask = BIT(4);
/* read out from vendor */
ath79_eth0_pll_data.pll_1000 = 0x2000000;
ath79_eth0_pll_data.pll_10 = 0x1313;
ath79_register_eth(0);
ath79_register_mdio(1, 0x0);
ath79_eth1_data.phy_mask = BIT(3);
ath79_register_eth(1);
}
MIPS_MACHINE(ATH79_MACH_UBNT_NANO_M_XW, "UBNT-NM-XW", "Ubiquiti Nanostation M XW",
ubnt_nano_m_xw_setup);
MIPS_MACHINE(ATH79_MACH_UBNT_LBE_M5, "UBNT-LBE-M5", "Ubiquiti Litebeam M5",
ubnt_lbe_m5_setup);
MIPS_MACHINE(ATH79_MACH_UBNT_LOCO_M_XW, "UBNT-LOCO-XW", "Ubiquiti Loco M XW",
ubnt_loco_m_xw_setup);
MIPS_MACHINE(ATH79_MACH_UBNT_ROCKET_M_XW, "UBNT-RM-XW", "Ubiquiti Rocket M XW",
ubnt_rocket_m_xw_setup);
MIPS_MACHINE(ATH79_MACH_UBNT_BULLET_M_XW, "UBNT-BM-XW", "Ubiquiti Bullet M XW",
ubnt_rocket_m_xw_setup);
MIPS_MACHINE(ATH79_MACH_UBNT_ROCKET_M_TI, "UBNT-RM-TI", "Ubiquiti Rocket M TI",
ubnt_rocket_m_ti_setup);
static struct gpio_led ubnt_airgateway_gpio_leds[] __initdata = {
{
.name = "ubnt:blue:wlan",
.gpio = 0,
}, {
.name = "ubnt:white:status",
.gpio = 1,
},
};
static struct gpio_keys_button airgateway_gpio_keys[] __initdata = {
{
.desc = "reset",
.type = EV_KEY,
.code = KEY_RESTART,
.debounce_interval = UBNT_XM_KEYS_DEBOUNCE_INTERVAL,
.gpio = 12,
.active_low = 1,
}
};
static void __init ubnt_airgateway_setup(void)
{
u32 t;
u8 *mac0 = (u8 *) KSEG1ADDR(0x1fff0000);
u8 *mac1 = (u8 *) KSEG1ADDR(0x1fff0000 + ETH_ALEN);
u8 *ee = (u8 *) KSEG1ADDR(0x1fff1000);
ath79_gpio_function_disable(AR933X_GPIO_FUNC_ETH_SWITCH_LED0_EN |
AR933X_GPIO_FUNC_ETH_SWITCH_LED1_EN |
AR933X_GPIO_FUNC_ETH_SWITCH_LED2_EN |
AR933X_GPIO_FUNC_ETH_SWITCH_LED3_EN |
AR933X_GPIO_FUNC_ETH_SWITCH_LED4_EN);
t = ath79_reset_rr(AR933X_RESET_REG_BOOTSTRAP);
t |= AR933X_BOOTSTRAP_MDIO_GPIO_EN;
ath79_reset_wr(AR933X_RESET_REG_BOOTSTRAP, t);
ath79_register_m25p80(NULL);
ath79_register_leds_gpio(-1, ARRAY_SIZE(ubnt_airgateway_gpio_leds),
ubnt_airgateway_gpio_leds);
ath79_register_gpio_keys_polled(-1, UBNT_XM_KEYS_POLL_INTERVAL,
ARRAY_SIZE(airgateway_gpio_keys),
airgateway_gpio_keys);
ath79_init_mac(ath79_eth1_data.mac_addr, mac0, 0);
ath79_init_mac(ath79_eth0_data.mac_addr, mac1, 0);
ath79_register_mdio(0, 0x0);
ath79_register_eth(1);
ath79_register_eth(0);
ath79_register_wmac(ee, NULL);
}
MIPS_MACHINE(ATH79_MACH_UBNT_AIRGW, "UBNT-AGW", "Ubiquiti AirGateway",
ubnt_airgateway_setup);
static struct gpio_led ubnt_airgateway_pro_gpio_leds[] __initdata = {
{
.name = "ubnt:blue:wlan",
.gpio = 13,
}, {
.name = "ubnt:white:status",
.gpio = 17,
},
};
static struct gpio_keys_button airgateway_pro_gpio_keys[] __initdata = {
{
.desc = "reset",
.type = EV_KEY,
.code = KEY_RESTART,
.debounce_interval = UBNT_XM_KEYS_DEBOUNCE_INTERVAL,
.gpio = 12,
.active_low = 1,
}
};
static void __init ubnt_airgateway_pro_setup(void)
{
u8 *eeprom = (u8 *) KSEG1ADDR(0x1fff0000);
u8 *mac0 = (u8 *) KSEG1ADDR(0x1fff0000);
ath79_register_m25p80(NULL);
ath79_register_leds_gpio(-1, ARRAY_SIZE(ubnt_airgateway_pro_gpio_leds),
ubnt_airgateway_pro_gpio_leds);
ath79_register_gpio_keys_polled(-1, UBNT_XM_KEYS_POLL_INTERVAL,
ARRAY_SIZE(airgateway_pro_gpio_keys),
airgateway_pro_gpio_keys);
ath79_register_wmac(eeprom + UAP_PRO_WMAC_CALDATA_OFFSET, NULL);
ap91_pci_init(eeprom + UAP_PRO_PCI_CALDATA_OFFSET, NULL);
ath79_setup_ar934x_eth_cfg(AR934X_ETH_CFG_SW_ONLY_MODE);
ath79_register_mdio(1, 0x0);
/* GMAC0 is left unused in this configuration */
/* GMAC1 is connected to MAC0 on the internal switch */
/* The PoE/WAN port connects to port 5 on the internal switch */
/* The LAN port connects to port 4 on the internal switch */
ath79_init_mac(ath79_eth1_data.mac_addr, mac0, 0);
ath79_eth1_data.phy_if_mode = PHY_INTERFACE_MODE_GMII;
ath79_register_eth(1);
}
MIPS_MACHINE(ATH79_MACH_UBNT_AIRGWP, "UBNT-AGWP", "Ubiquiti AirGateway Pro",
ubnt_airgateway_pro_setup);
Reference in New Issue View Git Blame Copy Permalink