mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-22 23:12:32 +00:00
0f5c28b96b
This commit adds support for Netgear Orbi Pro SXR80 and SXS80 (collectively known as SXK80)
Specifications:
---------------
* CPU: Qualcomm IPQ8074A Quad core Cortex-A53
* RAM: 1024MB
* Storage: SPI-NAND 512 MiB (Winbond W29N04GZ)
* Ethernet: 4x 1G RJ45 ports (QCA8075) 1x 2.5G RJ45 LAN/WAN (QCA8081)
* WLAN:
- 2.4 GHz: Qualcomm QCN5024 4x4
- 2x 5 GHz: Qualcomm QCN5054 4x4 (second radio high channels only)
* LEDs:
- Power: (Green and red)
- Front: (Blue, green, red and white)
* Buttons:
- 1x Soft reset
- 1x Sync/WPS
* Power: 12V DC Jack
Installation instructions (Telnet):
-----------------------------------
*Note, this guide assumes SXR80, for SXS80 change the firmware file name as appropriate
1. Put firmware file openwrt-qualcommax-ipq807x-netgear_sxr80-initramfs-uImage.itb in root of TFTP server available at 192.168.1.10.
2. Enable telnet by going to http://[ip of device]/debug.htm and clicking on the tickbox 'Enable telnet'
3. Telnet into the device and login using the same username and password as the web interface:
4. Run the following command:
`fw_setenv bootcmd 'env default -a; saveenv; reset'`
5. Reboot the router, once the web interface is available again re-enable telnet via http://[ip of device]/debug.htm and telnet into the device.
6. Run the following command:
`fw_printenv`
It should look similar to the below:
```
baudrate=115200
bootargs=console=ttyMSM0,115200n8
bootcmd=mii write 0x0 0x0 0x800; sleep 1; nmrp; bootdni; boot_DNI_secureboot
bootdelay=2
ipaddr=192.168.1.1
netmask=255.255.255.0
serverip=192.168.1.10
soc_version_major=2
soc_version_minor=0
```
**If you see the message:**
`Warning: Bad CRC, using default environment`
**DO NOT CONTINUE, YOU WILL BRICK YOUR DEVICE**
7. Run the following command:
`fw_setenv originalboot 'mii write 0x0 0x0 0x800; sleep 1; nmrp; bootdni; boot_DNI_secureboot'`
(This should match what's in the bootcmd variable displayed in step 6)
8. Run the following commands:
```
fw_setenv wrttftp 'mii write 0x0 0x0 0x800; sleep 1; nmrp; if tftpboot openwrt-qualcommax-ipq807x-netgear_sxr80-initramfs-uImage.itb; then bootm; fi; bootdni; boot_DNI_secureboot'
fw_setenv wrtboot 'mii write 0x0 0x0 0x800; sleep 1; nmrp; nand read 0x40000000 0x1980000 0x06d00000; bootm 0x40000000'
fw_setenv bootcmd 'run wrttftp'
```
9. Ensure SXR/S device is attached via ethernet (LAN port) to the same ethernet segment as the TFTP server.
10. Reboot the device, it should reboot into OpenWrt and be available on 192.168.1.1
11. Once OpenWrt has booted, update the bootcmd using the following command:
`fw_setenv bootcmd 'run wrtboot'`
12. Flash the sysupgrade image
13. It should boot into OpenWrt
References to SXK80 GPL source:
https://www.downloads.netgear.com/files/GPL/SXK80-V3.2.0.108_gpl_src.tar.bz2.zip
Signed-off-by: Flole Systems <flole@flole.de>
Signed-off-by: Andrew Smith <gul.code@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/14939
Signed-off-by: Robert Marko <robimarko@gmail.com>
187 lines
7.1 KiB
Makefile
187 lines
7.1 KiB
Makefile
include $(TOPDIR)/rules.mk
|
|
include $(INCLUDE_DIR)/version.mk
|
|
|
|
PKG_NAME:=ipq-wifi
|
|
PKG_RELEASE:=1
|
|
|
|
PKG_SOURCE_PROTO:=git
|
|
PKG_SOURCE_URL=$(PROJECT_GIT)/project/firmware/qca-wireless.git
|
|
PKG_SOURCE_DATE:=2024-04-26
|
|
PKG_SOURCE_VERSION:=644ba9ea2e6685e420561ef098cb6fbaaf136cbf
|
|
PKG_MIRROR_HASH:=3b913fd6fb0fac404b16e67c66d36c10315dba5459a8d495d870afcb1e2c33cd
|
|
PKG_FLAGS:=nonshared
|
|
|
|
include $(INCLUDE_DIR)/package.mk
|
|
|
|
define Build/Compile
|
|
endef
|
|
|
|
# Use ath10k-bdencoder from https://github.com/qca/qca-swiss-army-knife.git
|
|
# to generate the board-* files here.
|
|
#
|
|
# This is intended to be used on an interim basis until device-specific
|
|
# board data for new devices is available through the upstream compilation
|
|
#
|
|
# Please send a mail with your device-specific board files upstream.
|
|
# You can find instructions and examples on the linux-wireless wiki:
|
|
# <https://wireless.wiki.kernel.org/en/users/drivers/ath10k/boardfiles>
|
|
|
|
ALLWIFIBOARDS:= \
|
|
8devices_mango \
|
|
arcadyan_aw1000 \
|
|
buffalo_wxr-5950ax12 \
|
|
cmcc_rm2-6 \
|
|
compex_wpq873 \
|
|
dynalink_dl-wrx36 \
|
|
edgecore_eap102 \
|
|
edimax_cax1800 \
|
|
linksys_mx4200 \
|
|
linksys_mx5300 \
|
|
linksys_mx8500 \
|
|
netgear_lbr20 \
|
|
netgear_rax120v2 \
|
|
netgear_sxk80 \
|
|
netgear_wax214 \
|
|
netgear_wax218 \
|
|
netgear_wax620 \
|
|
netgear_wax630 \
|
|
prpl_haze \
|
|
qnap_301w \
|
|
redmi_ax6 \
|
|
spectrum_sax1v1k \
|
|
wallys_dr40x9 \
|
|
xiaomi_ax3600 \
|
|
xiaomi_ax9000 \
|
|
yyets_le1 \
|
|
yuncore_ax880 \
|
|
yuncore_fap650 \
|
|
zbtlink_zbt-z800ax \
|
|
zte_mf269 \
|
|
zte_mf287 \
|
|
zte_mf287plus \
|
|
zyxel_nbg7815
|
|
|
|
ALLWIFIPACKAGES:=$(foreach BOARD,$(ALLWIFIBOARDS),ipq-wifi-$(BOARD))
|
|
|
|
define Package/ipq-wifi-default
|
|
SUBMENU:=ath10k Board-Specific Overrides
|
|
SECTION:=firmware
|
|
CATEGORY:=Firmware
|
|
DEPENDS:=@(TARGET_ipq40xx||TARGET_ipq806x||TARGET_qualcommax)
|
|
TITLE:=Custom Board
|
|
endef
|
|
|
|
define ipq-wifi-install-one-to
|
|
$(INSTALL_DIR) $(2)/lib/firmware/ath10k/$(3)/
|
|
$(INSTALL_DATA) $(1) $(2)/lib/firmware/ath10k/$(3)/board-2.bin
|
|
endef
|
|
|
|
define ipq-wifi-install-ath11-one-to
|
|
$(INSTALL_DIR) $(2)/lib/firmware/ath11k/$(3)/
|
|
$(INSTALL_DATA) $(1) $(2)/lib/firmware/ath11k/$(3)/board-2.bin
|
|
endef
|
|
|
|
define ipq-wifi-install-one
|
|
$(if $(filter $(suffix $(1)),.QCA4019 .qca4019),\
|
|
$(call ipq-wifi-install-one-to,$(1),$(2),QCA4019/hw1.0),\
|
|
$(if $(filter $(suffix $(1)),.QCA9888 .qca9888),\
|
|
$(call ipq-wifi-install-one-to,$(1),$(2),QCA9888/hw2.0),\
|
|
$(if $(filter $(suffix $(1)),.QCA9889 .qca9889),\
|
|
$(call ipq-wifi-install-one-to,$(1),$(2),QCA9887/hw1.0),\
|
|
$(if $(filter $(suffix $(1)),.QCA9984 .qca9984),\
|
|
$(call ipq-wifi-install-one-to,$(1),$(2),QCA9984/hw1.0),\
|
|
$(if $(filter $(suffix $(1)),.QCA99X0 .qca99x0),\
|
|
$(call ipq-wifi-install-one-to,$(1),$(2),QCA99X0/hw2.0),\
|
|
$(if $(filter $(suffix $(1)),.IPQ6018 .ipq6018),\
|
|
$(call ipq-wifi-install-ath11-one-to,$(1),$(2),IPQ6018/hw1.0),\
|
|
$(if $(filter $(suffix $(1)),.IPQ8074 .ipq8074),\
|
|
$(call ipq-wifi-install-ath11-one-to,$(1),$(2),IPQ8074/hw2.0),\
|
|
$(if $(filter $(suffix $(1)),.QCN9074 .qcn9074),\
|
|
$(call ipq-wifi-install-ath11-one-to,$(1),$(2),QCN9074/hw1.0),\
|
|
$(error Unrecognized board-file suffix '$(suffix $(1))' for '$(1)')\
|
|
))))))))
|
|
|
|
endef
|
|
# Blank line required at end of above define due to foreach context
|
|
|
|
define generate-ipq-wifi-package
|
|
define Package/ipq-wifi-$(1)
|
|
$(call Package/ipq-wifi-default)
|
|
TITLE:=board-2.bin Overrides for $(2)
|
|
CONFLICTS:=$(PREV_BOARD)
|
|
endef
|
|
|
|
define Package/ipq-wifi-$(1)/description
|
|
The $(2) requires board-specific, reference ("cal") data
|
|
that is not yet present in the upstream wireless firmware distribution.
|
|
|
|
This package supplies board-2.bin file(s) that, in the interim,
|
|
overwrite those supplied by the ath10k-firmware-* packages.
|
|
|
|
This is package is only necessary for the $(2).
|
|
|
|
Do not install it for any other device!
|
|
endef
|
|
|
|
define Package/ipq-wifi-$(1)/install-overlay
|
|
$$$$(foreach IPQ_WIFI_BOARD_FILE,$$$$(wildcard $(PKG_BUILD_DIR)/board-$(1).*),\
|
|
$$$$(call ipq-wifi-install-one,$$$$(IPQ_WIFI_BOARD_FILE),$$(1)))
|
|
endef
|
|
|
|
PREV_BOARD+=ipq-wifi-$(1)
|
|
endef
|
|
|
|
# To add local files for testing:
|
|
# 1. create a new directory in the ipq-wifi package directory called "files".
|
|
# 2. place there the needed board files.
|
|
#
|
|
# To send a board file upstream:
|
|
# 1. create a pull request in https://github.com/openwrt/firmware_qca-wireless or
|
|
# send a patch to the mailing list adding the tag firmware/qca-wireless before
|
|
# the PATCH tag.
|
|
# 2. create a pull request in the main openwrt repository bumping the ipq-wifi
|
|
# package to the new version and adding the required lines to add the board file.
|
|
#
|
|
# Changes needed to the ipq-wifi Makefile:
|
|
# 1. Add board name to ALLWIFIBOARDS
|
|
# 2. Add $(eval $(call generate-ipq-wifi-package,<devicename>,<display name>))
|
|
#
|
|
# Board files should follow this name structure:
|
|
# board-<devicename>.<qca4019|qca9888|qca9889|qca9984|qca99x0|ipq8074>
|
|
|
|
$(eval $(call generate-ipq-wifi-package,8devices_mango,8devices Mango))
|
|
$(eval $(call generate-ipq-wifi-package,arcadyan_aw1000,Arcadyan AW1000))
|
|
$(eval $(call generate-ipq-wifi-package,buffalo_wxr-5950ax12,Buffalo WXR-5950AX12))
|
|
$(eval $(call generate-ipq-wifi-package,cmcc_rm2-6,CMCC RM2-6))
|
|
$(eval $(call generate-ipq-wifi-package,compex_wpq873,Compex WPQ-873))
|
|
$(eval $(call generate-ipq-wifi-package,dynalink_dl-wrx36,Dynalink DL-WRX36))
|
|
$(eval $(call generate-ipq-wifi-package,edgecore_eap102,Edgecore EAP102))
|
|
$(eval $(call generate-ipq-wifi-package,edimax_cax1800,Edimax CAX1800))
|
|
$(eval $(call generate-ipq-wifi-package,linksys_mx4200,Linksys MX4200))
|
|
$(eval $(call generate-ipq-wifi-package,linksys_mx5300,Linksys MX5300))
|
|
$(eval $(call generate-ipq-wifi-package,linksys_mx8500,Linksys MX8500))
|
|
$(eval $(call generate-ipq-wifi-package,netgear_lbr20,Netgear LBR20))
|
|
$(eval $(call generate-ipq-wifi-package,netgear_rax120v2,Netgear RAX120v2))
|
|
$(eval $(call generate-ipq-wifi-package,netgear_sxk80,Netgear SXK80))
|
|
$(eval $(call generate-ipq-wifi-package,netgear_wax214,Netgear WAX214))
|
|
$(eval $(call generate-ipq-wifi-package,netgear_wax218,Netgear WAX218))
|
|
$(eval $(call generate-ipq-wifi-package,netgear_wax620,Netgear WAX620))
|
|
$(eval $(call generate-ipq-wifi-package,netgear_wax630,Netgear WAX630))
|
|
$(eval $(call generate-ipq-wifi-package,qnap_301w,QNAP 301w))
|
|
$(eval $(call generate-ipq-wifi-package,prpl_haze,prpl Haze))
|
|
$(eval $(call generate-ipq-wifi-package,redmi_ax6,Redmi AX6))
|
|
$(eval $(call generate-ipq-wifi-package,spectrum_sax1v1k,Spectrum SAX1V1K))
|
|
$(eval $(call generate-ipq-wifi-package,wallys_dr40x9,Wallys DR40X9))
|
|
$(eval $(call generate-ipq-wifi-package,xiaomi_ax3600,Xiaomi AX3600))
|
|
$(eval $(call generate-ipq-wifi-package,xiaomi_ax9000,Xiaomi AX9000))
|
|
$(eval $(call generate-ipq-wifi-package,yyets_le1,YYeTs LE1))
|
|
$(eval $(call generate-ipq-wifi-package,yuncore_ax880,Yuncore AX880))
|
|
$(eval $(call generate-ipq-wifi-package,yuncore_fap650,Yuncore FAP650))
|
|
$(eval $(call generate-ipq-wifi-package,zbtlink_zbt-z800ax,Zbtlink ZBT-Z800AX))
|
|
$(eval $(call generate-ipq-wifi-package,zte_mf269,ZTE MF269))
|
|
$(eval $(call generate-ipq-wifi-package,zte_mf287,ZTE MF287))
|
|
$(eval $(call generate-ipq-wifi-package,zte_mf287plus,ZTE MF287Plus))
|
|
$(eval $(call generate-ipq-wifi-package,zyxel_nbg7815,Zyxel NBG7815))
|
|
|
|
$(foreach PACKAGE,$(ALLWIFIPACKAGES),$(eval $(call BuildPackage,$(PACKAGE))))
|