mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-27 17:18:59 +00:00
16b01fb1b9
Hardware
--------
SoC: NXP P1020 (2x e500 @ 800MHz)
RAM: 256M DDR3 (Micron)
FLASH: 32M NOR (Spansion S29GL128S)
BTN: 1x Reset
WiFi: 1x Atheros AR9590 2.4 bgn 3x3
2x Atheros AR9590 5.0 an 3x3
ETH: 1x Gigabit Ethernet (Atheros AR8033)
LED: System (green/red) - Radio{0,1} (green)
LAN (connected to PHY)
- GE blue
- FE green
Serial is a Cisco-compatible RJ45 next to the ethernet port.
115200-N-8 are the settings for OS and U-Boot.
Installation
------------
1. Grab the OpenWrt initramfs, rename it to 01C8A8C0.img. Place it in
the root directory of a TFTP server and serve it at
192.168.200.200/24.
2. Connect to the serial port and boot the AP. Stop autoboot in U-Boot
by pressing Enter when prompted. Credentials are identical to the one
in the APs interface. By default it is admin / new2day.
3. Set the bootcmd so the AP can boot OpenWrt by executing
$ setenv boot_openwrt "setenv bootargs;
cp.b 0xee000000 0x1000000 0x1000000; bootm 0x1000000"
$ setenv bootcmd "run boot_openwrt"
$ saveenv
If you plan on going back to the vendor firmware - the bootcmd for it
is stored in the boot_flash variable.
4. Load the initramfs image to RAM and boot by executing
$ tftpboot 0x1000000 192.168.200.200:01C8A8C0.img; bootm
5. Make a backup of the "firmware" partition if you ever wish to go back
to the vendor firmware.
6. Upload the OpenWrt sysupgrade image via SCP to the devices /tmp
folder.
7. Flash OpenWrt using sysupgrade.
$ sysupgrade -n /tmp/openwrt-sysupgrade.bin
Signed-off-by: David Bauer <mail@david-bauer.net>
31 lines
1.0 KiB
Diff
31 lines
1.0 KiB
Diff
--- a/arch/powerpc/platforms/85xx/Kconfig
|
|
+++ b/arch/powerpc/platforms/85xx/Kconfig
|
|
@@ -71,6 +71,17 @@ config PANDA
|
|
This board is a Concurrent Dual-Band wireless access point with a
|
|
Freescale P1020 SoC.
|
|
|
|
+config WS_AP3710I
|
|
+ bool "Enterasys WS-AP3710i"
|
|
+ select DEFAULT_UIMAGE
|
|
+ select ARCH_REQUIRE_GPIOLIB
|
|
+ select GPIO_MPC8XXX
|
|
+ help
|
|
+ This option enables support for the Enterasys WS-AP3710i board.
|
|
+
|
|
+ This board is a Concurrent Dual-Band wireless access point with a
|
|
+ Freescale P1020 SoC.
|
|
+
|
|
config MPC8540_ADS
|
|
bool "Freescale MPC8540 ADS"
|
|
select DEFAULT_UIMAGE
|
|
--- a/arch/powerpc/platforms/85xx/Makefile
|
|
+++ b/arch/powerpc/platforms/85xx/Makefile
|
|
@@ -24,6 +24,7 @@ obj-$(CONFIG_P1022_RDK) += p1022_rdk.o
|
|
obj-$(CONFIG_P1023_RDB) += p1023_rdb.o
|
|
obj-$(CONFIG_PANDA) += panda.o
|
|
obj-$(CONFIG_TWR_P102x) += twr_p102x.o
|
|
+obj-$(CONFIG_WS_AP3710I) += ws-ap3710i.o
|
|
obj-$(CONFIG_CORENET_GENERIC) += corenet_generic.o
|
|
obj-$(CONFIG_FB_FSL_DIU) += t1042rdb_diu.o
|
|
obj-$(CONFIG_RED_15W_REV1) += red15w_rev1.o
|