mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-22 15:02:32 +00:00
be89c9eec4
The DWR-961 A1 Wireless Router is based on the MT7620A SoC. It's a merge of two Amit boards: DWR-960 with ethernet part of Lava LR-25G001. ROMID it's taken from Telenor branded version and it works with tested device. Images from D-Link site for this router are from DWR-953 and it have ROMID DLK6E2424001. I don't know if it's mistake on web-site or if it's will require different image. Specification: - MediaTek MT7620A (580 Mhz) - 128 MB of RAM - 16 MB of FLASH - 1x 802.11bgn radio - 1x 802.11ac radio (MT7612 mpcie card) - 5x 10/100/1000 Mbps Ethernet: 4xLAN and 1xWAN (QCA8337) - 2x internal, non-detachable antennas (Wifi 2.4G) - 3x external, detachable antennas (2x LTE, 1x Wifi 5G) - 1x LTE modem cat 6 - UART (J5) header on PCB (57600 8n1) - 13x LED, 2x button - JBOOT bootloader Installation: Apply factory image via http web-gui or JBOOT recovery page How to revert to OEM firmware: - push the reset button and turn on the power. Wait until LED start blinking (~10sec.) - upload original factory image via JBOOT http (IP: 192.168.123.254) Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
63 lines
1.3 KiB
Plaintext
63 lines
1.3 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later
|
|
/*
|
|
* D-Link DWR-961 A1 Board Description
|
|
* Copyright 2022 Pawel Dembicki <paweldembicki@gmail.com>
|
|
*/
|
|
#include "mt7620a_dlink_dwr-96x.dtsi"
|
|
|
|
/ {
|
|
compatible = "dlink,dwr-961-a1", "ralink,mt7620a-soc";
|
|
model = "D-Link DWR-961 A1";
|
|
|
|
leds {
|
|
hidden-1 { /* hidden next to wlan5g led */
|
|
label = "green:hidden-1";
|
|
gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
hidden-2 { /* hidden next to sms led*/
|
|
label = "green:hidden-2";
|
|
gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
};
|
|
|
|
ðernet {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&rgmii1_pins &mdio_pins>;
|
|
|
|
port@5 {
|
|
status = "okay";
|
|
phy-mode = "rgmii";
|
|
mediatek,fixed-link = <1000 1 1 1>;
|
|
};
|
|
|
|
mdio-bus {
|
|
status = "okay";
|
|
|
|
ethernet-phy@0 {
|
|
reg = <0>;
|
|
phy-mode = "rgmii";
|
|
qca,ar8327-initvals = <
|
|
0x04 0x87300000 /* PORT0 PAD MODE CTRL */
|
|
0x0c 0x00000000 /* PORT6 PAD MODE CTRL */
|
|
0x7c 0x0000007e /* PORT0_STATUS */
|
|
0x80 0x00001200 /* PORT1_STATUS */
|
|
0x84 0x00001200 /* PORT2_STATUS */
|
|
0x88 0x00001200 /* PORT3_STATUS */
|
|
0x8c 0x00001200 /* PORT4_STATUS */
|
|
0x90 0x00001200 /* PORT5_STATUS */
|
|
0x94 0x00000000 /* PORT6_STATUS */
|
|
>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&gsw {
|
|
mediatek,ephy-base = /bits/ 8 <8>;
|
|
};
|
|
|
|
&wifi {
|
|
mediatek,mtd-eeprom = <&config 0xe29e>;
|
|
};
|