mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-20 22:23:27 +00:00
92a12c434c
It has been shown that the Fritz boxes have the correct mac address set in the wireless calibration data/eeeprom. Use this mac address as base for the ethernet and xdsl interface increment/decrement the address to match the values stored in the tffs. Signed-off-by: Mathias Kresin <dev@kresin.me>
161 lines
2.9 KiB
Plaintext
161 lines
2.9 KiB
Plaintext
/dts-v1/;
|
|
|
|
#include "ar9.dtsi"
|
|
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
model = "FRITZ7320 - 1&1 HomeServer";
|
|
|
|
chosen {
|
|
bootargs = "console=ttyLTQ0,115200";
|
|
};
|
|
|
|
aliases {
|
|
led-boot = &power;
|
|
led-failsafe = &power;
|
|
led-running = &power;
|
|
|
|
led-internet = &info_green;
|
|
led-dsl = &power;
|
|
led-wifi = &wlan;
|
|
};
|
|
|
|
memory@0 {
|
|
reg = <0x0 0x4000000>;
|
|
};
|
|
|
|
fpi@10000000 {
|
|
localbus@0 {
|
|
nor-boot@0 {
|
|
compatible = "lantiq,nor";
|
|
bank-width = <2>;
|
|
reg = <0 0x0 0x1000000>;
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
ath9k_cal: partition@0 {
|
|
label = "urlader";
|
|
reg = <0x00000 0x20000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@20000 {
|
|
label = "firmware";
|
|
reg = <0x20000 0xf60000>;
|
|
};
|
|
|
|
partition@f80000 {
|
|
label = "tffs (1)";
|
|
reg = <0xf80000 0x40000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@fc0000 {
|
|
label = "tffs (2)";
|
|
reg = <0xfc0000 0x40000>;
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
gpio: pinmux@E100B10 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&state_default>;
|
|
|
|
state_default: pinmux {
|
|
pci {
|
|
lantiq,groups = "gnt1", "req1", "req2", "req3", "req4", "gnt2", "gnt3", "gnt4";
|
|
lantiq,function = "pci";
|
|
};
|
|
pci-in {
|
|
lantiq,groups = "req1", "req2", "req3", "req4";
|
|
lantiq,output = <0>;
|
|
lantiq,open-drain = <1>;
|
|
lantiq,pull = <2>;
|
|
};
|
|
pci-out {
|
|
lantiq,groups = "gnt1", "gnt2", "gnt3", "gnt4";
|
|
lantiq,output = <1>;
|
|
lantiq,pull = <0>;
|
|
};
|
|
};
|
|
};
|
|
|
|
etop@E180000 {
|
|
phy-mode = "mii";
|
|
mtd-mac-address = <&ath9k_cal 0xa91>;
|
|
mtd-mac-address-increment = <(-2)>;
|
|
};
|
|
|
|
ifxhcd@E101000 {
|
|
status = "okay";
|
|
};
|
|
};
|
|
|
|
gpio-keys-polled {
|
|
compatible = "gpio-keys-polled";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
poll-interval = <100>;
|
|
|
|
rfkill {
|
|
label = "rfkill";
|
|
gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_RFKILL>;
|
|
};
|
|
dect {
|
|
label = "dect";
|
|
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_PHONE>;
|
|
};
|
|
};
|
|
|
|
gpio-leds {
|
|
compatible = "gpio-leds";
|
|
power: power {
|
|
label = "fritz7320:green:power";
|
|
gpios = <&gpio 44 GPIO_ACTIVE_LOW>;
|
|
default-state = "keep";
|
|
};
|
|
voice {
|
|
label = "fritz7320:green:fon";
|
|
gpios = <&gpio 47 GPIO_ACTIVE_LOW>;
|
|
};
|
|
dect {
|
|
label = "fritz7320:green:dect";
|
|
gpios = <&gpio 38 GPIO_ACTIVE_LOW>;
|
|
};
|
|
wlan: wlan {
|
|
label = "fritz7320:green:wlan";
|
|
gpios = <&gpio 37 GPIO_ACTIVE_LOW>;
|
|
};
|
|
info_green: info_green {
|
|
label = "fritz7320:green:info";
|
|
gpios = <&gpio 35 GPIO_ACTIVE_LOW>;
|
|
};
|
|
info_red {
|
|
label = "fritz7320:red:info";
|
|
gpios = <&gpio 45 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&pci0 {
|
|
status = "okay";
|
|
req-mask = <0xf>;
|
|
gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>;
|
|
|
|
wifi@0,0 {
|
|
compatible = "pci0,0";
|
|
reg = <0x7000 0 0 0 0>;
|
|
qca,no-eeprom; /* load from ath9k-eeprom-pci-0000:00:0e.0.bin */
|
|
};
|
|
};
|