mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-27 17:18:59 +00:00
e9f9cd14cc
Due to licensing uncertainty, we do not include the firmwares for the wireless chips used in the Raspberry Pi Zero 2 W. To have working wireless, follow the instructions below. For people building their own images: mkdir -p files/lib/firmware/brcm wget -P files/lib/firmware/brcm/ https://github.com/RPi-Distro/firmware-nonfree/raw/bullseye/debian/config/brcm80211/brcm/brcmfmac43436-sdio.bin wget -P files/lib/firmware/brcm/ https://github.com/RPi-Distro/firmware-nonfree/raw/bullseye/debian/config/brcm80211/brcm/brcmfmac43436-sdio.txt wget -P files/lib/firmware/brcm/ https://github.com/RPi-Distro/firmware-nonfree/raw/bullseye/debian/config/brcm80211/brcm/brcmfmac43436s-sdio.bin wget -P files/lib/firmware/brcm/ https://github.com/RPi-Distro/firmware-nonfree/raw/bullseye/debian/config/brcm80211/brcm/brcmfmac43436s-sdio.txt Now build the OpenWrt image as usual, and it will include the firmware files in the correct location. For people using ext4 images: Write the ext4 image to the sdcard, then mount the 2nd partition and put the firmware files from the links above in /lib/firmware/brcm relative from the mount point where the partition is mounted. For people using squashfs images: Write the squashfs image to the sdcard, place it in the Raspberry Pi Zero 2 W, boot it and wait for the overlay filesystem to be created. Find the offset of the overlay filesystem in sysfs: # cat /sys/devices/virtual/block/loop0/loop/offset 25755648 Shut down the device, unplug the power and move the SD card to a Linux computer. Mount the 2nd partition of the sdcard as a loop device with the offset found earlier. sudo mount /dev/sdh2 -o loop,offset=25755648 /mnt/temp Put the firmware files from the links above in /upper/lib/firmware/brcm relative to the mount point where the loop device is mounted. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Tested-by: Peter van Dijk <peter@7bits.nl>
44 lines
779 B
Bash
44 lines
779 B
Bash
#!/bin/sh
|
|
# Copyright (C) 2015-2016 OpenWrt.org
|
|
# Copyright (C) 2017 LEDE project
|
|
|
|
. /lib/functions.sh
|
|
. /lib/functions/leds.sh
|
|
|
|
set_state() {
|
|
case "$(board_name)" in
|
|
raspberrypi,2-model-b |\
|
|
raspberrypi,2-model-b-rev2 |\
|
|
raspberrypi,3-model-b |\
|
|
raspberrypi,3-model-b-plus |\
|
|
raspberrypi,400 |\
|
|
raspberrypi,4-compute-module |\
|
|
raspberrypi,4-model-b |\
|
|
raspberrypi,model-b-plus)
|
|
status_led="led1"
|
|
;;
|
|
raspberrypi,3-compute-module |\
|
|
raspberrypi,model-b |\
|
|
raspberrypi,model-zero |\
|
|
raspberrypi,model-zero-2 |\
|
|
raspberrypi,model-zero-w)
|
|
status_led="led0"
|
|
;;
|
|
esac
|
|
|
|
case "$1" in
|
|
preinit)
|
|
status_led_blink_preinit
|
|
;;
|
|
failsafe)
|
|
status_led_blink_failsafe
|
|
;;
|
|
preinit_regular)
|
|
status_led_blink_preinit_regular
|
|
;;
|
|
done)
|
|
status_led_on
|
|
;;
|
|
esac
|
|
}
|