mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-27 01:11:14 +00:00
7e21ce8e2b
This model is almost identical to the EAP225 v3.
Major difference is the RTL8211FS PHY Chipset.
Device specifications:
* SoC: QCA9563 @ 775MHz
* RAM: 128MiB DDR2
* Flash: 16MiB SPI-NOR
* Wireless 2.4GHz (SoC): b/g/n, 3x3
* Wireless 5Ghz (QCA9886): a/n/ac, 2x2 MU-MIMO
* Ethernet (RTL8211FS): 1× 1GbE, 802.3at PoE
Flashing instructions:
* ssh into target device and run `cliclientd stopcs`
* Upgrade with factory image via web interface
Debricking:
* Serial port can be soldered on PCB J4 (1: TXD, 2: RXD, 3: GND, 4: VCC)
* Bridge unpopulated resistors R225 (TXD) and R237 (RXD).
Do NOT bridge R230.
* Use 3.3V, 115200 baud, 8n1
* Interrupt bootloader by holding CTRL+B during boot
* tftp initramfs to flash via LuCI web interface
setenv ipaddr 192.168.1.1 # default, change as required
setenv serverip 192.168.1.10 # default, change as required
tftp 0x80800000 initramfs.bin
bootelf $fileaddr
MAC addresses:
MAC address (as on device label) is stored in device info partition at
an offset of 8 bytes. ath9k device has same address as ethernet, ath10k
uses address incremented by 1.
Signed-off-by: Sven Hauer <sven.hauer+github@uniku.de>
60 lines
1.0 KiB
Plaintext
60 lines
1.0 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
#include "qca9563_tplink_eap2x5-1port.dtsi"
|
|
|
|
/ {
|
|
compatible = "tplink,eap225-v4", "qca,qca9563";
|
|
model = "TP-Link EAP225 v4";
|
|
|
|
aliases {
|
|
led-boot = &led_status_green;
|
|
led-failsafe = &led_status_amber;
|
|
led-running = &led_status_green;
|
|
led-upgrade = &led_status_amber;
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
led_status_green: status_green {
|
|
label = "green:status";
|
|
gpios = <&gpio 7 GPIO_ACTIVE_HIGH>;
|
|
default-state = "on";
|
|
};
|
|
|
|
led_status_amber: status_amber {
|
|
label = "amber:status";
|
|
gpios = <&gpio 9 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&art {
|
|
precalibration_ath10k: pre-calibration@5000 {
|
|
reg = <0x5000 0x2f20>;
|
|
};
|
|
};
|
|
|
|
ð0 {
|
|
phy-handle = <&phy6>;
|
|
phy-mode = "sgmii";
|
|
};
|
|
|
|
&mdio0 {
|
|
phy6: ethernet-phy@6 {
|
|
reg = <6>;
|
|
};
|
|
};
|
|
|
|
&pcie {
|
|
wifi@0,0 {
|
|
compatible = "qcom,ath10k";
|
|
reg = <0 0 0 0 0>;
|
|
|
|
mac-address-increment = <1>;
|
|
|
|
nvmem-cells = <&macaddr_info_8>, <&precalibration_ath10k>;
|
|
nvmem-cell-names = "mac-address", "pre-calibration";
|
|
};
|
|
};
|