mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-27 01:11:14 +00:00
52992efc34
FCC ID: A8J-EWS660AP
Engenius EWS660AP is an outdoor wireless access point with
2 gigabit ethernet ports, dual-band wireless,
internal antenna plates, and 802.3at PoE+
**Specification:**
- QCA9558 SOC 2.4 GHz, 3x3
- QCA9880 WLAN mini PCIe card, 5 GHz, 3x3, 26dBm
- AR8035-A PHY RGMII GbE with PoE+ IN
- AR8033 PHY SGMII GbE with PoE+ OUT
- 40 MHz clock
- 16 MB FLASH MX25L12845EMI-10G
- 2x 64 MB RAM
- UART at J1 populated, RX grounded
- 6 internal antenna plates (5 dbi, omni-directional)
- 5 LEDs, 1 button (power, eth0, eth1, 2G, 5G) (reset)
**MAC addresses:**
Base MAC addressed labeled as "MAC"
Only one Vendor MAC address in flash
eth0 *:d4 MAC art 0x0
eth1 *:d5 --- art 0x0 +1
phy1 *:d6 --- art 0x0 +2
phy0 *:d7 --- art 0x0 +3
**Serial Access:**
the RX line on the board for UART is shorted to ground by resistor R176
therefore it must be removed to use the console
but it is not necessary to remove to view boot log
optionally, R175 can be replaced with a solder bridge short
the resistors R175 and R176 are next to the UART RX pin
**Installation:**
2 ways to flash factory.bin from OEM:
Method 1: Firmware upgrade page:
OEM webpage at 192.168.1.1
username and password "admin"
Navigate to "Firmware Upgrade" page from left pane
Click Browse and select the factory.bin image
Upload and verify checksum
Click Continue to confirm and wait 3 minutes
Method 2: Serial to load Failsafe webpage:
After connecting to serial console and rebooting...
Interrupt uboot with any key pressed rapidly
execute `run failsafe_boot` OR `bootm 0x9fd70000`
wait a minute
connect to ethernet and navigate to
"192.168.1.1/index.htm"
Select the factory.bin image and upload
wait about 3 minutes
**Return to OEM:**
If you have a serial cable, see Serial Failsafe instructions
otherwise, uboot-env can be used to make uboot load the failsafe image
ssh into openwrt and run
`fw_setenv rootfs_checksum 0`
reboot, wait 3 minutes
connect to ethernet and navigate to 192.168.1.1/index.htm
select OEM firmware image from Engenius and click upgrade
**TFTP recovery:**
Requires serial console, reset button does nothing
rename initramfs.bin to '0101A8C0.img'
make available on TFTP server at 192.168.1.101
power board, interrupt boot
execute tftpboot and bootm 0x81000000
**Format of OEM firmware image:**
The OEM software of EWS660AP is a heavily modified version
of Openwrt Kamikaze. One of the many modifications
is to the sysupgrade program. Image verification is performed
simply by the successful ungzip and untar of the supplied file
and name check and header verification of the resulting contents.
To form a factory.bin that is accepted by OEM Openwrt build,
the kernel and rootfs must have specific names...
openwrt-ar71xx-generic-ews660ap-uImage-lzma.bin
openwrt-ar71xx-generic-ews660ap-root.squashfs
and begin with the respective headers (uImage, squashfs).
Then the files must be tarballed and gzipped.
The resulting binary is actually a tar.gz file in disguise.
This can be verified by using binwalk on the OEM firmware images,
ungzipping then untaring.
Newer EnGenius software requires more checks but their script
includes a way to skip them, otherwise the tar must include
a text file with the version and md5sums in a deprecated format.
The OEM upgrade script is at /etc/fwupgrade.sh.
OKLI kernel loader is required because the OEM software
expects the kernel to be no greater than 1536k
and the factory.bin upgrade procedure would otherwise
overwrite part of the kernel when writing rootfs.
Note on PLL-data cells:
The default PLL register values will not work
because of the external AR8035 switch between
the SOC and the ethernet port.
For QCA955x series, the PLL registers for eth0 and eth1
can be see in the DTSI as 0x28 and 0x48 respectively.
Therefore the PLL registers can be read from uboot
for each link speed after attempting tftpboot
or another network action using that link speed
with `md 0x18050028 1` and `md 0x18050048 1`.
The clock delay required for RGMII can be applied
at the PHY side, using the at803x driver `phy-mode`.
Therefore the PLL registers for GMAC0
do not need the bits for delay on the MAC side.
This is possible due to fixes in at803x driver
since Linux 5.1 and 5.3
Tested-by: Niklas Arnitz <openwrt@arnitz.email>
Signed-off-by: Michael Pratt <mcpratt@pm.me>
133 lines
2.2 KiB
Plaintext
133 lines
2.2 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
#include "qca955x_senao_loader.dtsi"
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
compatible = "engenius,ews660ap", "qca,qca9558";
|
|
model = "EnGenius EWS660AP";
|
|
|
|
aliases {
|
|
label-mac-device = ð0;
|
|
led-boot = &led_wifi5g;
|
|
led-failsafe = &led_wifi5g;
|
|
led-upgrade = &led_wifi5g;
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
reset {
|
|
label = "reset";
|
|
gpios = <&gpio 21 GPIO_ACTIVE_LOW>;
|
|
debounce-interval = <60>;
|
|
linux,code = <KEY_RESTART>;
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
wifi2g {
|
|
label = "green:wifi2g";
|
|
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
|
|
linux,default-trigger = "phy1tpt";
|
|
};
|
|
|
|
led_wifi5g: wifi5g {
|
|
label = "green:wifi5g";
|
|
gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
|
|
linux,default-trigger = "phy0tpt";
|
|
};
|
|
};
|
|
};
|
|
|
|
&partitions {
|
|
partition@ff0000 {
|
|
label = "art";
|
|
reg = <0xff0000 0x010000>;
|
|
read-only;
|
|
|
|
compatible = "nvmem-cells";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
macaddr_art_0: macaddr@0 {
|
|
reg = <0x0 0x6>;
|
|
};
|
|
|
|
calibration_art_1000: calibration@1000 {
|
|
reg = <0x1000 0x440>;
|
|
};
|
|
|
|
calibration_art_5000: calibration@5000 {
|
|
reg = <0x5000 0x844>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&mdio0 {
|
|
status = "okay";
|
|
|
|
phy1: ethernet-phy@1 {
|
|
reg = <1>;
|
|
eee-broken-100tx;
|
|
eee-broken-1000t;
|
|
};
|
|
|
|
phy2: ethernet-phy@2 {
|
|
reg = <2>;
|
|
eee-broken-100tx;
|
|
eee-broken-1000t;
|
|
at803x-override-sgmii-link-check;
|
|
};
|
|
};
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
|
|
nvmem-cells = <&macaddr_art_0>;
|
|
nvmem-cell-names = "mac-address";
|
|
|
|
phy-handle = <&phy1>;
|
|
phy-mode = "rgmii-id";
|
|
|
|
pll-data = <0x82000000 0x80000101 0x80001313>;
|
|
};
|
|
|
|
ð1 {
|
|
status = "okay";
|
|
|
|
nvmem-cells = <&macaddr_art_0>;
|
|
nvmem-cell-names = "mac-address";
|
|
mac-address-increment = <1>;
|
|
|
|
phy-handle = <&phy2>;
|
|
|
|
pll-data = <0x03000000 0x00000101 0x00001313>;
|
|
|
|
qca955x-sgmii-fixup;
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
|
|
nvmem-cells = <&macaddr_art_0>, <&calibration_art_1000>;
|
|
nvmem-cell-names = "mac-address", "calibration";
|
|
mac-address-increment = <2>;
|
|
};
|
|
|
|
&ath10k_1 {
|
|
status = "okay";
|
|
|
|
nvmem-cells = <&macaddr_art_0>, <&calibration_art_5000>;
|
|
nvmem-cell-names = "mac-address", "calibration";
|
|
mac-address-increment = <3>;
|
|
};
|
|
|
|
&pcie1 {
|
|
status = "okay";
|
|
};
|