mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-19 13:48:06 +00:00
8b0407d15d
it is possible to boot and run OpenWrt from an image on an USB-Stick
on the MyBook Live DUO. (No, the MyBook Live Single does NOT have an
USB-Port and attempts at enabling it sadly all failed... so far).
To do that:
First, prepare a USB-Stick by writing the raw and uncompressed OpenWRT
factory image for the device onto the stick (i.e.
# gunzip -c openwrt-*wd_mybooklive*-factory.img.gz > /dev/sd$XX).
Then enter the u-boot via an attached TTL/CMOS 3.3V cable adapter and
give the following commands a try in the:
usb start; sata init
ext2load usb 0:1 ${fdt_addr_r} /boot/apollo3g.dtb
ext2load usb 0:1 ${kernel_addr_r} /boot/uImage
setenv bootargs 'root=/dev/sdc2 rw rootfstype=squashfs,ext4 rootdelay=5'
run addtty; bootm ${kernel_addr_r} - ${fdt_addr_r}
Notes:
- booting from USB-Sticks takes a long time! Be prepared to wait a few
minutes. (~3 minutes for 4 MiB /boot/uImage file on a USB 2.0 Stick)
- the bootargs part 'root=/dev/sdX2' depends on how many HDDs/SSDs are
slotted in. (if none: then use sda, if one: sdb. if two: sdc)
- rootdelay is important as the storage on the USB-Sticks do not show
up fast enough. 5 seconds might be excessive though.
- it's possible to concat these commands together in one line and
write it into u-boot's "bootcmd" environment variable and save the
environment to make the device to always boot from USB from then on.
if you have accidentally overridden the 'bootcmd' and want to return
to 'spec' enter the following commands :
setenv bootcmd 'run boot_sata_script_ap2nc'
saveenv
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
63 lines
1.4 KiB
Plaintext
63 lines
1.4 KiB
Plaintext
CONFIG_APOLLO3G=y
|
|
CONFIG_BROADCOM_PHY=y
|
|
CONFIG_EXT4_FS=y
|
|
# CONFIG_SATA_DWC_OLD_DMA is not set
|
|
CONFIG_ATA=y
|
|
CONFIG_ATA_SFF=y
|
|
CONFIG_ATA_BMDMA=y
|
|
CONFIG_SATA_PMP=y
|
|
CONFIG_GENERIC_PHY=y
|
|
CONFIG_SATA_DWC=y
|
|
# CONFIG_SATA_DWC_DEBUG is not set
|
|
CONFIG_CRYPTO_MD5_PPC=y
|
|
CONFIG_CRYPTO_SHA1_PPC=y
|
|
CONFIG_EXT4_FS=y
|
|
CONFIG_F2FS_FS=y
|
|
CONFIG_FREEZER=y
|
|
CONFIG_FW_CACHE=y
|
|
CONFIG_SCSI=y
|
|
CONFIG_BLK_DEV_SD=y
|
|
CONFIG_BLK_PM=y
|
|
CONFIG_GPIO_GENERIC=y
|
|
CONFIG_GPIO_GENERIC_PLATFORM=y
|
|
CONFIG_GPIO_74XX_MMIO=y
|
|
CONFIG_LEDS_TRIGGER_DISK=y
|
|
CONFIG_BLK_DEV_LOOP=y
|
|
CONFIG_BLK_DEV_DM=y
|
|
CONFIG_BLK_DEV_DM_BUILTIN=y
|
|
CONFIG_BLK_DEV_MD=y
|
|
CONFIG_MD=y
|
|
CONFIG_MD_AUTODETECT=y
|
|
# CONFIG_MD_LINEAR is not set
|
|
# CONFIG_MD_MULTIPATH is not set
|
|
CONFIG_MD_RAID0=y
|
|
CONFIG_MD_RAID1=y
|
|
# CONFIG_MD_RAID10 is not set
|
|
# CONFIG_MD_RAID456 is not set
|
|
CONFIG_MTD_PHYSMAP=y
|
|
CONFIG_MTD_JEDECPROBE=y
|
|
CONFIG_PM=y
|
|
CONFIG_PM_AUTOSLEEP=y
|
|
CONFIG_PM_CLK=y
|
|
CONFIG_PM_SLEEP=y
|
|
# CONFIG_PM_USERSPACE_AUTOSLEEP is not set
|
|
CONFIG_PM_WAKELOCKS=y
|
|
CONFIG_PM_WAKELOCKS_GC=y
|
|
CONFIG_PM_WAKELOCKS_LIMIT=100
|
|
CONFIG_PPC_EARLY_DEBUG=y
|
|
CONFIG_PPC_EARLY_DEBUG_44x=y
|
|
# CONFIG_PPC_EARLY_DEBUG_MEMCONS is not set
|
|
# CONFIG_PPC_EARLY_DEBUG_16550 is not set
|
|
CONFIG_PPC_EARLY_DEBUG_44x_PHYSHIGH=0x4
|
|
CONFIG_PPC_EARLY_DEBUG_44x_PHYSLOW=0xef600300
|
|
CONFIG_PPC4xx_CPM=y
|
|
CONFIG_REGULATOR_FIXED_VOLTAGE=y
|
|
CONFIG_SUSPEND=y
|
|
CONFIG_SUSPEND_FREEZER=y
|
|
CONFIG_USB=y
|
|
CONFIG_USB_COMMON=y
|
|
CONFIG_USB_DWC2=y
|
|
CONFIG_USB_DWC2_HOST=y
|
|
CONFIG_USB_ROLE_SWITCH=y
|
|
CONFIG_USB_STORAGE=y
|