mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-23 07:22:33 +00:00
3a4b751110
The uart node is enabled on all devices except one (GL-USB150 *). Thus, let's not have a few hundred nodes to enable it, but do not disable it in the first place. Where the majority of devices is using it, also move the serial0 alias to the DTSI. *) Since GL-USB150 even defines serial0 alias, the missing uart is probably just a mistake. Anyway, disable it for now so this patch stays cosmetic. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
125 lines
1.8 KiB
Plaintext
125 lines
1.8 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
#include "ar9331.dtsi"
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
model = "8devices Carambola2";
|
|
compatible = "8dev,carambola2", "qca,ar9331";
|
|
|
|
aliases {
|
|
label-mac-device = &wmac;
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
wlan {
|
|
label = "green:wlan";
|
|
gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
|
|
linux,default-trigger = "phy0tpt";
|
|
};
|
|
|
|
eth0 {
|
|
label = "orange:eth0";
|
|
gpios = <&gpio 13 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
eth1 {
|
|
label = "orange:eth1";
|
|
gpios = <&gpio 14 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
wps {
|
|
label = "wps";
|
|
linux,code = <KEY_WPS_BUTTON>;
|
|
gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&ref {
|
|
clock-frequency = <40000000>;
|
|
};
|
|
|
|
&usb {
|
|
dr_mode = "host";
|
|
status = "okay";
|
|
};
|
|
|
|
&usb_phy {
|
|
status = "okay";
|
|
};
|
|
|
|
&spi {
|
|
status = "okay";
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
spi-max-frequency = <50000000>;
|
|
reg = <0>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
uboot: partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x000000 0x040000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@40000 {
|
|
label = "u-boot-env";
|
|
reg = <0x040000 0x010000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@50000 {
|
|
compatible = "denx,uimage";
|
|
label = "firmware";
|
|
reg = <0x50000 0xfa0000>;
|
|
};
|
|
|
|
art: partition@ff0000 {
|
|
label = "art";
|
|
reg = <0xff0000 0x010000>;
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&mdio0 {
|
|
status = "okay";
|
|
};
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
mtd-mac-address = <&art 0x0>;
|
|
|
|
gmac-config {
|
|
device = <&gmac>;
|
|
|
|
switch-phy-addr-swap = <1>;
|
|
switch-phy-swap = <1>;
|
|
};
|
|
};
|
|
|
|
ð1 {
|
|
status = "okay";
|
|
mtd-mac-address = <&art 0x6>;
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
mtd-cal-data = <&art 0x1000>;
|
|
};
|