openwrt/target/linux/ath79/dts/qca955x_elecom_wab.dtsi
INAGAKI Hiroshi af611bce44 Revert "ath79: elecom,wab: use nvmem"
This reverts commit 70e41d0205.

"ethaddr" is stored into the "u-boot-env" (stock: "Config") partition
and it's quoted with double-quotations, but that format is not supported
by the current NVMEM u-boot-env driver (and mac_pton() function) and the
MAC address won't be parsed to byte array.
This causes random MAC addresses on the adapters, so revert the above
commit.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17116
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-11-29 15:02:48 +01:00

258 lines
4.3 KiB
Plaintext

// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
#include "qca955x.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/leds/common.h>
/ {
aliases {
led-boot = &led_status;
led-failsafe = &led_status;
led-upgrade = &led_status;
};
leds {
compatible = "gpio-leds";
led-0 {
gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
color = <LED_COLOR_ID_GREEN>;
function = LED_FUNCTION_WLAN;
function-enumerator = <24>;
linux,default-trigger = "phy1tpt";
};
led_status: led-1 {
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
color = <LED_COLOR_ID_RED>;
function = LED_FUNCTION_STATUS;
};
led-2 {
gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
color = <LED_COLOR_ID_GREEN>;
function = LED_FUNCTION_USB;
trigger-sources = <&usb_port1>;
linux,default-trigger = "usbport";
};
};
keys {
compatible = "gpio-keys";
button-wps {
label = "wps";
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
linux,code = <KEY_WPS_BUTTON>;
debounce-interval = <60>;
};
button-reset {
label = "reset";
gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
debounce-interval = <60>;
};
button-eject {
label = "eject";
gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
linux,code = <KEY_EJECTCD>;
debounce-interval = <60>;
};
};
beeper {
compatible = "gpio-beeper";
gpios = <&gpio 4 GPIO_ACTIVE_HIGH>;
};
reg_usb_vbus: regulator {
compatible = "regulator-fixed";
regulator-name = "usb-vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
gpios = <&gpio 11 GPIO_ACTIVE_HIGH>;
enable-active-high;
regulator-always-on;
};
watchdog {
compatible = "linux,wdt-gpio";
gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
hw_algo = "toggle";
hw_margin_ms = <300>;
always-running;
};
};
&mdio0 {
status = "okay";
ethphy4: ethernet-phy@4 {
compatible = "ethernet-phy-id004d,d072",
"ethernet-phy-ieee802.3-c22";
reg = <0x4>;
eee-broken-100tx;
eee-broken-1000t;
};
};
&eth0 {
status = "okay";
phy-handle = <&ethphy4>;
phy-mode = "rgmii-rxid";
pll-data = <0xae000000 0x80000101 0x80001313>;
gmac-config {
device = <&gmac>;
rxdv-delay = <3>;
rxd-delay = <3>;
txen-delay = <0>;
txd-delay = <0>;
rgmii-enabled = <1>;
};
};
&mdio1 {
status = "okay";
ethphy1: ethernet-phy@1 {
compatible = "ethernet-phy-id004d,d074",
"ethernet-phy-ieee802.3-c22";
reg = <0x1>;
at803x-override-sgmii-link-check;
};
};
&eth1 {
status = "okay";
phy-handle = <&ethphy1>;
pll-data = <0x03000000 0x00000101 0x00001313>;
qca955x-sgmii-fixup;
};
&pcie0 {
status = "okay";
wifi@0,0 {
compatible = "qcom,ath10k";
reg = <0x0000 0 0 0 0>;
nvmem-cells = <&cal_art_5000>;
nvmem-cell-names = "calibration";
};
};
&spi {
status = "okay";
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <25000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "u-boot";
reg = <0x0 0x40000>;
read-only;
};
partition@40000 {
label = "u-boot-env";
reg = <0x40000 0x10000>;
read-only;
};
partition@50000 {
label = "art";
reg = <0x50000 0x10000>;
read-only;
nvmem-layout {
compatible = "fixed-layout";
#address-cells = <1>;
#size-cells = <1>;
cal_art_1000: calibration@1000 {
reg = <0x1000 0x440>;
};
cal_art_5000: calibration@5000 {
reg = <0x5000 0x844>;
};
};
};
partition@60000 {
label = "art2";
reg = <0x60000 0x10000>;
read-only;
};
partition@70000 {
compatible = "denx,uimage";
label = "firmware";
reg = <0x70000 0xe00000>;
};
partition@e70000 {
label = "manufacture";
reg = <0xe70000 0x100000>;
read-only;
};
partition@f70000 {
label = "backup";
reg = <0xf70000 0x10000>;
read-only;
};
partition@f80000 {
label = "storage";
reg = <0xf80000 0x80000>;
read-only;
};
};
};
};
&usb_phy0 {
status = "okay";
};
&usb0 {
#address-cells = <1>;
#size-cells = <0>;
status = "okay";
dr_mode = "host";
vbus-supply = <&reg_usb_vbus>;
usb_port1: port@1 {
reg = <1>;
#trigger-source-cells = <0>;
};
};
&wdt {
status = "disabled";
};
&wmac {
status = "okay";
nvmem-cells = <&cal_art_1000>;
nvmem-cell-names = "calibration";
};