openwrt/target/linux/ath79/image
Xinfa Deng dd8a4a8c34 ath79: add support for GL.iNet GL-X1200
This patch adds supports for GL-X1200.

Specification:
	- SOC: QCA9563 (775MHz)
	- Flash: 16 MiB
	- RAM: 128 MiB DDR2
	- Ethernet: 4x 1Gbps LAN + 1x 1Gbps WAN
	- Wireless: QCA9563(2.4GHz) and QCA9886(5GHz)
	- SIM: 2x SIM card slots
	- MicroSD: 1x microSD slot
	- Antenna: 2x external 5dBi antennas
	- USB: 1x USB 2.0 port
	- Button: 1x reset button
	- LED: 16x LEDs (3x GPIO controllable)
	- UART: 1x UART on PCB (JP1: 3.3V, RX, TX, GND)
	- OEM U-Boot supplies HTTP/GUI access

Implementation Notes
====================

Both the NOR and NAND variants boot off a NOR-based kernel,
consistent with the OEM's firmware.

The mode LEDs are
    * Boot, Running   system
    * Failsafe        2G
    * Upgrade         5G

Installation
============

Using sysupgrade
----------------

sysupgrade may be used to install a NAND image on a device running
a NAND image or a NOR image on a device running a NOR image. It is
recommended to *not* preserve config when upgrading from OEM firmware
or previous versions of OpenWrt. No supported sysupgrade path should
require "force". Transitioning from NOR to NAND can be accomplished

Using U-Boot
------------

The OEM U-Boot can be put into a graphical, firmware-upload mode by
holding down the button on the side of the router while applying power
and for a bit more than five seconds following with the current OEM
U-Boot. The power LED will come on, then the 5G LED will flash five
times, about once a second.  When the 5G LED stops flashing and the
2G LED lights solid, the router's U-Boot will provide an upload page
at http://192.168.1.1/ Either a browser may be used to upload an image,
or a utility such as curl may be used:

curl -X POST -F gl_firmware=\@*-nand-squashfs-factory.img \
         http://192.168.1.1/index.html
or
    curl -X POST -F gl_firmware=\@*-nor-squashfs-sysupgrade.bin \
         http://192.168.1.1/index.html

Note that NOR vs. NAND is based on the file name extension.

Signed-off-by: Xinfa Deng <xinfa.deng@gl-inet.com>
2023-02-25 14:31:42 +01:00
..
bin ath79: add support for PISEN WMB001N 2019-08-08 21:00:59 +08:00
lzma-loader ath79: lzma-loader: allow setting custom kernel magic 2021-04-08 09:20:59 +02:00
common-buffalo.mk ath79: use common device definition for Buffalo devices 2020-09-16 17:31:03 +02:00
common-mikrotik.mk ath79: mikrotik: use OpenWrt loader for initram image 2022-09-11 01:30:11 +02:00
common-netgear.mk tools/squashfs: rename to squashfs3-lzma 2023-02-18 21:11:36 +01:00
common-senao.mk ath79: use lzma-loader for Senao initramfs images 2023-01-06 15:34:07 +01:00
common-tp-link.mk treewide: call check-size before append-metadata 2021-07-10 19:40:10 +02:00
common-ubnt.mk ath79: switch some RedBoot based devices to OKLI loader 2022-06-24 17:09:54 +02:00
common-yuncore.mk ath79: add support for YunCore TFTP image generation 2019-11-25 17:32:46 +01:00
generic-tp-link.mk ath79: add support for TP-Link CPE605-v1 2022-12-13 23:17:27 +01:00
generic-ubnt.mk treewide: replace wpad-basic-wolfssl default 2023-02-04 02:35:03 +01:00
generic.mk ath79: add support for Senao Engenius ESR1200 2023-02-12 18:07:31 +01:00
Makefile ath79: image: don't depend on other COMPILE targets 2022-12-19 12:27:35 +00:00
mikrotik.mk ath79: add support for RouterBOARD mAP 2022-06-29 12:36:04 +02:00
nand.mk ath79: add support for GL.iNet GL-X1200 2023-02-25 14:31:42 +01:00
tiny-netgear.mk ath79: netgear: trim down uImage customisations 2020-11-25 16:33:49 +01:00
tiny-tp-link.mk ath79: tiny: Do not build TPLink WPA8630Pv2 by default 2023-01-06 18:52:01 +01:00
tiny-ubnt.mk ath79: move ubnt-xm to tiny 2022-06-11 21:22:58 +02:00
tiny.mk ath79: image: use 'kmod-usb-chipidea2' for AR933x devices 2022-02-21 22:22:30 +01:00