mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-23 15:32:33 +00:00
0d23fd2ab2
>From the Documentation/devicetree/bindings/leds/common.txt: - default-state : The initial state of the LED. Valid values are "on", "off", and "keep". If the LED is already on or off and the default-state property is set the to same value, then no glitch should be produced where the LED momentarily turns off (or on). The "keep" setting will keep the LED at whatever its current state is, without producing a glitch. The default is off if this property is not present. So setting the default-state of the LEDs to `off` is redundant as `off` is default LED state anyway. We should remove it as almost every new PR/patch submission contains this property by default which seems to be just copy&paste from some DTS file already present in the tree. Signed-off-by: Petr Štetiar <ynezz@true.cz>
128 lines
1.8 KiB
Plaintext
128 lines
1.8 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
/dts-v1/;
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
#include "ar9331.dtsi"
|
|
|
|
/ {
|
|
model = "eTactica EG200";
|
|
compatible = "etactica,eg200", "qca,ar9331";
|
|
|
|
aliases {
|
|
serial0 = &uart;
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys-polled";
|
|
poll-interval = <50>;
|
|
|
|
restore {
|
|
linux,code = <KEY_WPS_BUTTON>;
|
|
gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
modbus {
|
|
label = "eg200:red:modbus";
|
|
gpios = <&gpio 16 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
etactica {
|
|
label = "eg200:red:etactica";
|
|
gpios = <&gpio 15 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
eth0 {
|
|
label = "eg200:red:eth0";
|
|
gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
wlan {
|
|
label = "eg200:red:wlan";
|
|
gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
|
|
linux,default-trigger = "phy0tpt";
|
|
};
|
|
};
|
|
};
|
|
|
|
&uart {
|
|
status = "okay";
|
|
};
|
|
|
|
&gpio {
|
|
status = "okay";
|
|
};
|
|
|
|
&usb {
|
|
dr_mode = "host";
|
|
status = "okay";
|
|
};
|
|
|
|
&usb_phy {
|
|
status = "okay";
|
|
};
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
mtd-mac-address = <&art 0x0>;
|
|
|
|
gmac-config {
|
|
device = <&gmac>;
|
|
switch-phy-addr-swap = <1>;
|
|
switch-phy-swap = <1>;
|
|
};
|
|
};
|
|
|
|
ð1 {
|
|
status = "okay";
|
|
compatible = "syscon", "simple-mfd";
|
|
};
|
|
|
|
&spi {
|
|
num-chipselects = <1>;
|
|
status = "okay";
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
spi-max-frequency = <50000000>;
|
|
reg = <0>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
uboot@0 {
|
|
reg = <0x0 0x40000>;
|
|
read-only;
|
|
};
|
|
|
|
uboot-env@40000 {
|
|
reg = <0x40000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
firmware@50000 {
|
|
compatible = "denx,uimage";
|
|
reg = <0x50000 0xfa0000>;
|
|
};
|
|
|
|
art: art@ff0000 {
|
|
reg = <0xff0000 0x10000>;
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
mtd-cal-data = <&art 0x1000>;
|
|
mtd-mac-address = <&art 0x1002>;
|
|
};
|