mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-24 07:46:48 +00:00
f574b535eb
Hardware
--------
SoC: Qualcomm IPQ8065
RAM: 512 MB DDR3
Flash: 256 MB NAND (Macronix MX30UF2G18AC) (split into 2x128MB)
4 MB SPI-NOR (Macronix MX25U3235F)
WLAN: Qualcomm Atheros QCA9984 - 2.4Ghz
Qualcomm Atheros QCA9984 - 5Ghz
ETH: eth0 - POE (100Mbps in U-Boot, 1000Mbps in OpenWrt)
eth1 - (1000Mbps in both)
Auto-negotiation broken on both.
USB: USB 2.0
LED: 5G, 2.4G, ETH1, ETH2, CTRL, PWR (All support green and red)
BTN: Reset
Other: SD card slot (non-functional)
Serial: 115200bps, near the Ethernet transformers, labeled 9X.
Connections from the arrow to the 9X text:
[NC] - [TXD] - [GND] - [RXD] - [NC]
Installation
------------
0. Connect to the device
Plug your computer into LAN2 (1000Mbps connection required).
If you use the LAN1/POE port, set your computer to force a 100Mbps link.
Connect to the device via TTL (Serial) 115200n8.
Locate the header (or solder pads) labeled 9X,
near the Ethernet jacks/transformers.
There should be an arrow on the other side of the header marking.
The connections should go like this:
(from the arrow to the 9X text): NC - TXD - GND - RXD - NC
1. Prepare for installation
While the AP is powering up, interrupt the startup process.
MAKE SURE TO CHECK YOUR CURRENT PARTITION!
If you see: "Current Partition is : partB" or
"Need to switch partition from partA to partB",
you have to force the device into partA mode, before continuing.
This can be done by changing the PKRstCnt to 5 and resetting the device.
setenv PKRstCnt 5
saveenv
reset
After you interrupt the startup process again,
you should see: Need to switch partition from partB to partA
You can now continue to the next step.
If you see: "Current Partition is : partA",
you can continue to the next step.
2. Prevent partition switching.
To prevent the device from switching partitions,
we are going to modify the startup command.
set bootcmd "setenv PKRstCnt 0; saveenv; bootipq"
setenv
3. First boot
Now, we have to boot the OpenWrt intifs.
The easiest way to do this is by using Tiny PXE.
You can also use the normal U-Boot tftp method.
Run "bootp" this will get an IP from the DHCP server
and possibly the firmware image.
If it doesn't download the firmware image, run "tftpboot".
Now run "bootm" to run the image.
You might see:
"ERROR: new format image overwritten - must RESET the board to recover"
this means that the image you are trying to load is too big.
Use a smaller image for the initial boot.
4. Install OpenWrt from initfs
Once you are booted into OpenWrt,
transfer the OpenWrt upgrade image and
use sysupgrade to install OpenWrt to the device.
Signed-off-by: Kristjan Krušič <kristjan.krusic@krusic22.com>
491 lines
13 KiB
Makefile
491 lines
13 KiB
Makefile
DEVICE_VARS += NETGEAR_BOARD_ID NETGEAR_HW_ID
|
|
DEVICE_VARS += TPLINK_BOARD_ID
|
|
|
|
define Device/kernel-size-migration
|
|
DEVICE_COMPAT_VERSION := 2.0
|
|
DEVICE_COMPAT_MESSAGE := *** Kernel partition size has changed from earlier \
|
|
versions. You need to sysupgrade with the OpenWrt factory image and \
|
|
use the force flag when image check fails. Settings will be lost. ***
|
|
endef
|
|
|
|
define Build/buffalo-rootfs-cksum
|
|
( \
|
|
echo -ne "\x$$(od -A n -t u1 $@ | tr -s ' ' '\n' | \
|
|
$(STAGING_DIR_HOST)/bin/awk '{s+=$$0}END{printf "%x", 255-s%256}')"; \
|
|
) >> $@
|
|
endef
|
|
|
|
define Build/edimax-header
|
|
$(eval edimax_model=$(word 1,$(1)))
|
|
|
|
$(STAGING_DIR_HOST)/bin/mkedimaximg \
|
|
-b -s CSYS -m $(edimax_model) \
|
|
-f 0x70000 -S 0x1200000 \
|
|
-i $@ -o $@.new
|
|
@mv $@.new $@
|
|
endef
|
|
|
|
define Device/DniImage
|
|
KERNEL_SUFFIX := -uImage
|
|
KERNEL = kernel-bin | append-dtb | uImage none
|
|
KERNEL_NAME := zImage
|
|
NETGEAR_BOARD_ID :=
|
|
NETGEAR_HW_ID :=
|
|
UBINIZE_OPTS := -E 5
|
|
IMAGES += factory.img
|
|
IMAGE/factory.img := append-kernel | pad-offset $$$$(BLOCKSIZE) 64 | \
|
|
append-uImage-fakehdr filesystem | pad-to $$$$(KERNEL_SIZE) | \
|
|
append-ubi | netgear-dni
|
|
IMAGE/sysupgrade.bin := append-kernel | pad-offset $$$$(BLOCKSIZE) 64 | \
|
|
append-uImage-fakehdr filesystem | sysupgrade-tar kernel=$$$$@ | \
|
|
append-metadata
|
|
endef
|
|
|
|
define Device/TpSafeImage
|
|
KERNEL_SUFFIX := -uImage
|
|
KERNEL = kernel-bin | append-dtb | uImage none
|
|
KERNEL_NAME := zImage
|
|
TPLINK_BOARD_ID :=
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-rootfs | tplink-safeloader factory
|
|
IMAGE/sysupgrade.bin := append-rootfs | \
|
|
tplink-safeloader sysupgrade | append-metadata
|
|
endef
|
|
|
|
define Device/ZyXELImage
|
|
KERNEL_SUFFIX := -uImage
|
|
KERNEL = kernel-bin | append-dtb | uImage none | \
|
|
pad-to $$(KERNEL_SIZE)
|
|
KERNEL_NAME := zImage
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-rootfs | pad-rootfs | \
|
|
pad-to $$$$(BLOCKSIZE) | zyxel-ras-image separate-kernel
|
|
IMAGE/sysupgrade.bin/squashfs := append-rootfs | \
|
|
pad-to $$$$(BLOCKSIZE) | sysupgrade-tar rootfs=$$$$@ | \
|
|
append-metadata
|
|
endef
|
|
|
|
define Device/arris_tr4400-v2
|
|
$(call Device/LegacyImage)
|
|
DEVICE_VENDOR := Arris
|
|
DEVICE_MODEL := TR4400
|
|
DEVICE_VARIANT := v2
|
|
SOC := qcom-ipq8065
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
DEVICE_PACKAGES := ath10k-firmware-qca9984-ct ath10k-firmware-qca99x0-ct
|
|
KERNEL_IN_UBI := 1
|
|
endef
|
|
TARGET_DEVICES += arris_tr4400-v2
|
|
|
|
define Device/askey_rt4230w-rev6
|
|
$(call Device/LegacyImage)
|
|
DEVICE_VENDOR := Askey
|
|
DEVICE_MODEL := RT4230W
|
|
DEVICE_VARIANT := REV6
|
|
SOC := qcom-ipq8065
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
DEVICE_PACKAGES := ath10k-firmware-qca9984-ct
|
|
KERNEL_IN_UBI := 1
|
|
endef
|
|
TARGET_DEVICES += askey_rt4230w-rev6
|
|
|
|
define Device/asrock_g10
|
|
$(call Device/FitImage)
|
|
$(call Device/UbiFit)
|
|
SOC := qcom-ipq8064
|
|
DEVICE_VENDOR := ASRock
|
|
DEVICE_MODEL := G10
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_SIZE := 5332k
|
|
DEVICE_PACKAGES := kmod-i2c-gpio ath10k-firmware-qca99x0-ct
|
|
IMAGE/nand-factory.bin := append-ubi | edimax-header RN67
|
|
endef
|
|
TARGET_DEVICES += asrock_g10
|
|
|
|
define Device/buffalo_wxr-2533dhp
|
|
$(call Device/LegacyImage)
|
|
SOC := qcom-ipq8064
|
|
DEVICE_VENDOR := Buffalo
|
|
DEVICE_MODEL := WXR-2533DHP
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
IMAGE_SIZE := 65536k
|
|
KERNEL_IN_UBI := 1
|
|
IMAGE/sysupgrade.bin := append-rootfs | buffalo-rootfs-cksum | \
|
|
sysupgrade-tar rootfs=$$$$@ | append-metadata
|
|
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct
|
|
endef
|
|
TARGET_DEVICES += buffalo_wxr-2533dhp
|
|
|
|
define Device/compex_wpq864
|
|
$(call Device/FitImage)
|
|
$(call Device/UbiFit)
|
|
DEVICE_VENDOR := Compex
|
|
DEVICE_MODEL := WPQ864
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
SOC := qcom-ipq8064
|
|
DEVICE_PACKAGES := kmod-gpio-beeper
|
|
endef
|
|
TARGET_DEVICES += compex_wpq864
|
|
|
|
define Device/edgecore_ecw5410
|
|
$(call Device/FitImage)
|
|
$(call Device/UbiFit)
|
|
DEVICE_VENDOR := Edgecore
|
|
DEVICE_MODEL := ECW5410
|
|
SOC := qcom-ipq8068
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
DEVICE_DTS_CONFIG := config@v2.0-ap160
|
|
DEVICE_PACKAGES := ath10k-firmware-qca9984-ct \
|
|
ipq-wifi-edgecore_ecw5410
|
|
endef
|
|
TARGET_DEVICES += edgecore_ecw5410
|
|
|
|
define Device/linksys_ea7500-v1
|
|
$(call Device/LegacyImage)
|
|
$(Device/kernel-size-migration)
|
|
DEVICE_VENDOR := Linksys
|
|
DEVICE_MODEL := EA7500
|
|
DEVICE_VARIANT := v1
|
|
SOC := qcom-ipq8064
|
|
PAGESIZE := 2048
|
|
BLOCKSIZE := 128k
|
|
KERNEL_SIZE := 4096k
|
|
KERNEL = kernel-bin | append-dtb | uImage none | \
|
|
append-uImage-fakehdr filesystem
|
|
UBINIZE_OPTS := -E 5
|
|
IMAGES := factory.bin sysupgrade.bin
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | \
|
|
append-ubi | pad-to $$$$(PAGESIZE)
|
|
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct
|
|
endef
|
|
TARGET_DEVICES += linksys_ea7500-v1
|
|
|
|
define Device/linksys_ea8500
|
|
$(call Device/LegacyImage)
|
|
$(Device/kernel-size-migration)
|
|
DEVICE_VENDOR := Linksys
|
|
DEVICE_MODEL := EA8500
|
|
SOC := qcom-ipq8064
|
|
PAGESIZE := 2048
|
|
BLOCKSIZE := 128k
|
|
KERNEL_SIZE := 4096k
|
|
KERNEL = kernel-bin | append-dtb | uImage none | \
|
|
append-uImage-fakehdr filesystem
|
|
BOARD_NAME := ea8500
|
|
SUPPORTED_DEVICES += ea8500
|
|
UBINIZE_OPTS := -E 5
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | \
|
|
append-ubi
|
|
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct
|
|
endef
|
|
TARGET_DEVICES += linksys_ea8500
|
|
|
|
define Device/meraki_mr42
|
|
$(call Device/FitImage)
|
|
DEVICE_VENDOR := Cisco Meraki
|
|
DEVICE_MODEL := MR42
|
|
SOC := qcom-ipq8068
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_LOADADDR = 0x44208000
|
|
DEVICE_PACKAGES := -swconfig -kmod-ata-ahci -kmod-ata-ahci-platform \
|
|
-kmod-usb-ohci -kmod-usb2 -kmod-usb-ledtrig-usbport \
|
|
-kmod-phy-qcom-ipq806x-usb -kmod-usb3 -kmod-usb-dwc3-qcom \
|
|
-uboot-envtools ath10k-firmware-qca9887-ct \
|
|
ath10k-firmware-qca99x0-ct kmod-eeprom-at24 kmod-hwmon-ina2xx \
|
|
kmod-leds-tlc591xx
|
|
endef
|
|
TARGET_DEVICES += meraki_mr42
|
|
|
|
define Device/meraki_mr52
|
|
$(call Device/FitImage)
|
|
DEVICE_VENDOR := Cisco Meraki
|
|
DEVICE_MODEL := MR52
|
|
SOC := qcom-ipq8068
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_LOADADDR = 0x44208000
|
|
DEVICE_DTS_CONFIG := config@2
|
|
DEVICE_PACKAGES := -swconfig -kmod-ata-ahci -kmod-ata-ahci-platform \
|
|
-kmod-usb-ohci -kmod-usb2 -kmod-usb-ledtrig-usbport \
|
|
-kmod-phy-qcom-ipq806x-usb -kmod-usb3 -kmod-usb-dwc3-qcom \
|
|
-uboot-envtools ath10k-firmware-qca9887-ct \
|
|
ath10k-firmware-qca9984-ct kmod-eeprom-at24 kmod-hwmon-ina2xx \
|
|
kmod-leds-tlc591xx
|
|
endef
|
|
TARGET_DEVICES += meraki_mr52
|
|
|
|
define Device/nec_wg2600hp
|
|
$(call Device/LegacyImage)
|
|
DEVICE_VENDOR := NEC
|
|
DEVICE_MODEL := Aterm WG2600HP
|
|
SOC := qcom-ipq8064
|
|
BLOCKSIZE := 64k
|
|
BOARD_NAME := wg2600hp
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | \
|
|
pad-rootfs | append-metadata
|
|
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct
|
|
endef
|
|
TARGET_DEVICES += nec_wg2600hp
|
|
|
|
define Device/nec_wg2600hp3
|
|
$(call Device/LegacyImage)
|
|
DEVICE_VENDOR := NEC Platforms
|
|
DEVICE_MODEL := Aterm WG2600HP3
|
|
SOC := qcom-ipq8062
|
|
BLOCKSIZE := 64k
|
|
IMAGES := sysupgrade.bin
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | \
|
|
pad-rootfs | append-metadata
|
|
DEVICE_PACKAGES := -kmod-ata-ahci -kmod-ata-ahci-platform \
|
|
-kmod-usb-ohci -kmod-usb2 -kmod-usb-ledtrig-usbport \
|
|
-kmod-usb-phy-qcom-dwc3 -kmod-usb3 -kmod-usb-dwc3-qcom \
|
|
ath10k-firmware-qca9984-ct
|
|
endef
|
|
TARGET_DEVICES += nec_wg2600hp3
|
|
|
|
define Device/netgear_d7800
|
|
$(call Device/DniImage)
|
|
DEVICE_VENDOR := NETGEAR
|
|
DEVICE_MODEL := Nighthawk X4 D7800
|
|
SOC := qcom-ipq8064
|
|
KERNEL_SIZE := 4096k
|
|
NETGEAR_BOARD_ID := D7800
|
|
NETGEAR_HW_ID := 29764958+0+128+512+4x4+4x4
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
BOARD_NAME := d7800
|
|
SUPPORTED_DEVICES += d7800
|
|
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct
|
|
DEVICE_COMPAT_VERSION := 2.0
|
|
DEVICE_COMPAT_MESSAGE := Sysupgrade does not work due to rootfs ubi partition size change. \
|
|
Use factory image with the TFTP recovery flash routine.
|
|
endef
|
|
TARGET_DEVICES += netgear_d7800
|
|
|
|
define Device/netgear_r7500
|
|
$(call Device/DniImage)
|
|
DEVICE_VENDOR := NETGEAR
|
|
DEVICE_MODEL := Nighthawk X4 R7500
|
|
DEVICE_VARIANT := v1
|
|
SOC := qcom-ipq8064
|
|
KERNEL_SIZE := 4096k
|
|
NETGEAR_BOARD_ID := R7500
|
|
NETGEAR_HW_ID := 29764841+0+128+256+3x3+4x4
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
BOARD_NAME := r7500
|
|
SUPPORTED_DEVICES += r7500
|
|
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct
|
|
endef
|
|
TARGET_DEVICES += netgear_r7500
|
|
|
|
define Device/netgear_r7500v2
|
|
$(call Device/DniImage)
|
|
DEVICE_VENDOR := NETGEAR
|
|
DEVICE_MODEL := Nighthawk X4 R7500
|
|
DEVICE_VARIANT := v2
|
|
SOC := qcom-ipq8064
|
|
KERNEL_SIZE := 4096k
|
|
NETGEAR_BOARD_ID := R7500v2
|
|
NETGEAR_HW_ID := 29764958+0+128+512+3x3+4x4
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
BOARD_NAME := r7500v2
|
|
SUPPORTED_DEVICES += r7500v2
|
|
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct \
|
|
ath10k-firmware-qca988x-ct
|
|
endef
|
|
TARGET_DEVICES += netgear_r7500v2
|
|
|
|
define Device/netgear_r7800
|
|
$(call Device/DniImage)
|
|
DEVICE_VENDOR := NETGEAR
|
|
DEVICE_MODEL := Nighthawk X4S R7800
|
|
SOC := qcom-ipq8065
|
|
KERNEL_SIZE := 4096k
|
|
NETGEAR_BOARD_ID := R7800
|
|
NETGEAR_HW_ID := 29764958+0+128+512+4x4+4x4+cascade
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
BOARD_NAME := r7800
|
|
SUPPORTED_DEVICES += r7800
|
|
DEVICE_PACKAGES := ath10k-firmware-qca9984-ct kmod-ramoops
|
|
endef
|
|
TARGET_DEVICES += netgear_r7800
|
|
|
|
define Device/netgear_xr500
|
|
$(call Device/DniImage)
|
|
DEVICE_VENDOR := NETGEAR
|
|
DEVICE_MODEL := Nighthawk XR500
|
|
SOC := qcom-ipq8065
|
|
KERNEL_SIZE := 4096k
|
|
NETGEAR_BOARD_ID := XR500
|
|
NETGEAR_HW_ID := 29764958+0+256+512+4x4+4x4+cascade
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
DEVICE_PACKAGES := ath10k-firmware-qca9984-ct kmod-ramoops
|
|
endef
|
|
TARGET_DEVICES += netgear_xr500
|
|
|
|
define Device/nokia_ac400i
|
|
$(call Device/FitImage)
|
|
$(call Device/UbiFit)
|
|
DEVICE_VENDOR := Nokia
|
|
DEVICE_MODEL := AC400i
|
|
SOC := qcom-ipq8065
|
|
DEVICE_DTS := qcom-ipq8065-ac400i
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
BOARD_NAME := ac400i
|
|
DEVICE_PACKAGES := ath10k-firmware-qca9984-ct ipq-wifi-nokia-ac400i
|
|
endef
|
|
TARGET_DEVICES += nokia_ac400i
|
|
|
|
define Device/qcom_ipq8064-ap148
|
|
$(call Device/FitImage)
|
|
$(call Device/UbiFit)
|
|
DEVICE_VENDOR := Qualcomm
|
|
DEVICE_MODEL := AP148
|
|
DEVICE_VARIANT := standard
|
|
SOC := qcom-ipq8064
|
|
DEVICE_DTS := qcom-ipq8064-ap148
|
|
KERNEL_INSTALL := 1
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
BOARD_NAME := ap148
|
|
SUPPORTED_DEVICES += ap148
|
|
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct
|
|
endef
|
|
TARGET_DEVICES += qcom_ipq8064-ap148
|
|
|
|
define Device/qcom_ipq8064-ap148-legacy
|
|
$(call Device/LegacyImage)
|
|
$(call Device/UbiFit)
|
|
DEVICE_VENDOR := Qualcomm
|
|
DEVICE_MODEL := AP148
|
|
DEVICE_VARIANT := legacy
|
|
SOC := qcom-ipq8064
|
|
DEVICE_DTS := qcom-ipq8064-ap148
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
BOARD_NAME := ap148
|
|
SUPPORTED_DEVICES := qcom,ipq8064-ap148 ap148
|
|
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct
|
|
endef
|
|
TARGET_DEVICES += qcom_ipq8064-ap148-legacy
|
|
|
|
define Device/qcom_ipq8064-ap161
|
|
$(call Device/FitImage)
|
|
$(call Device/UbiFit)
|
|
DEVICE_VENDOR := Qualcomm
|
|
DEVICE_MODEL := AP161
|
|
SOC := qcom-ipq8064
|
|
DEVICE_DTS := qcom-ipq8064-ap161
|
|
KERNEL_INSTALL := 1
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
BOARD_NAME := ap161
|
|
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct
|
|
endef
|
|
TARGET_DEVICES += qcom_ipq8064-ap161
|
|
|
|
define Device/qcom_ipq8064-db149
|
|
$(call Device/FitImage)
|
|
DEVICE_VENDOR := Qualcomm
|
|
DEVICE_MODEL := DB149
|
|
SOC := qcom-ipq8064
|
|
DEVICE_DTS := qcom-ipq8064-db149
|
|
KERNEL_INSTALL := 1
|
|
BOARD_NAME := db149
|
|
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct
|
|
endef
|
|
TARGET_DEVICES += qcom_ipq8064-db149
|
|
|
|
define Device/tplink_ad7200
|
|
$(call Device/TpSafeImage)
|
|
DEVICE_VENDOR := TP-Link
|
|
DEVICE_MODEL := AD7200
|
|
DEVICE_VARIANT := v1/v2
|
|
DEVICE_ALT0_VENDOR := TP-Link
|
|
DEVICE_ALT0_MODEL := Talon AD7200
|
|
DEVICE_ALT0_VARIANT := v1/v2
|
|
SOC := qcom-ipq8064
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
TPLINK_BOARD_ID := AD7200
|
|
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct kmod-ramoops kmod-wil6210
|
|
endef
|
|
TARGET_DEVICES += tplink_ad7200
|
|
|
|
define Device/tplink_c2600
|
|
$(call Device/TpSafeImage)
|
|
DEVICE_VENDOR := TP-Link
|
|
DEVICE_MODEL := Archer C2600
|
|
DEVICE_VARIANT := v1
|
|
SOC := qcom-ipq8064
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
BOARD_NAME := c2600
|
|
SUPPORTED_DEVICES += c2600
|
|
TPLINK_BOARD_ID := C2600
|
|
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct kmod-ramoops
|
|
endef
|
|
TARGET_DEVICES += tplink_c2600
|
|
|
|
define Device/tplink_vr2600v
|
|
DEVICE_VENDOR := TP-Link
|
|
DEVICE_MODEL := Archer VR2600v
|
|
DEVICE_VARIANT := v1
|
|
KERNEL_SUFFIX := -uImage
|
|
KERNEL = kernel-bin | append-dtb | uImage none
|
|
KERNEL_NAME := zImage
|
|
IMAGE_SIZE := 12672k
|
|
SOC := qcom-ipq8064
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
BOARD_NAME := vr2600v
|
|
SUPPORTED_DEVICES += vr2600v
|
|
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct
|
|
IMAGE/sysupgrade.bin := pad-extra 512 | append-kernel | \
|
|
append-rootfs | pad-rootfs | append-metadata
|
|
endef
|
|
TARGET_DEVICES += tplink_vr2600v
|
|
|
|
define Device/ubnt_unifi-ac-hd
|
|
$(call Device/FitImageLzma)
|
|
DEVICE_VENDOR := Ubiquiti
|
|
DEVICE_MODEL := UniFi AC HD
|
|
SOC := qcom-ipq8064
|
|
BLOCKSIZE := 64k
|
|
IMAGE_SIZE := 14784k
|
|
DEVICE_PACKAGES := ath10k-firmware-qca9984-ct
|
|
IMAGE/sysupgrade.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
|
append-rootfs | pad-rootfs | check-size | append-metadata
|
|
endef
|
|
TARGET_DEVICES += ubnt_unifi-ac-hd
|
|
|
|
define Device/zyxel_nbg6817
|
|
DEVICE_VENDOR := ZyXEL
|
|
DEVICE_MODEL := NBG6817
|
|
SOC := qcom-ipq8065
|
|
KERNEL_SIZE := 4096k
|
|
BLOCKSIZE := 64k
|
|
BOARD_NAME := nbg6817
|
|
RAS_BOARD := NBG6817
|
|
RAS_ROOTFS_SIZE := 20934k
|
|
RAS_VERSION := "V1.99(OWRT.9999)C0"
|
|
SUPPORTED_DEVICES += nbg6817
|
|
DEVICE_PACKAGES := ath10k-firmware-qca9984-ct e2fsprogs \
|
|
kmod-fs-ext4 losetup
|
|
$(call Device/ZyXELImage)
|
|
endef
|
|
TARGET_DEVICES += zyxel_nbg6817
|