mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-22 15:02:32 +00:00
ac03e24635
TP-Link CPE710-v1 is an outdoor wireless CPE for 5 GHz with one Ethernet port based on the AP152 reference board Specifications: - SoC: QCA9563-AL3A MIPS 74kc @ 775MHz, AHB @ 258MHz - RAM: 128MiB DDR2 @ 650MHz - Flash: 16MiB SPI NOR Based on the GD25Q128 - Wi-Fi 5Ghz: ath10k chip (802.11ac for up to 867Mbps on 5GHz wireless data rate) Based on the QCA9896 - Ethernet: one 1GbE port - 23dBi high-gain directional 2×2 MIMO antenna and a dedicated metal reflector - Power, LAN, WLAN5G Blue LEDs - 3x Blue LEDs Flashing instructions: Flash factory image through stock firmware WEB UI or through TFTP To get to TFTP recovery just hold reset button while powering on for around 30-40 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP address:192.168.0.254 Signed-off-by: Andrew Cameron <apcameron@softhome.net> [convert to nvmem, fix MAC assignment in 11-ath10k-caldata] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
153 lines
2.4 KiB
Plaintext
153 lines
2.4 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
#include "qca956x.dtsi"
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
model = "TP-Link CPE710 v1";
|
|
compatible = "tplink,cpe710-v1", "qca,qca9563";
|
|
|
|
aliases {
|
|
label-mac-device = ð0;
|
|
led-boot = &led_lan;
|
|
led-failsafe = &led_lan;
|
|
led-upgrade = &led_lan;
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
led_lan: lan {
|
|
label = "blue:lan";
|
|
gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
wlan5g {
|
|
label = "blue:wlan5g";
|
|
gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
|
|
linux,default-trigger = "phy0tpt";
|
|
};
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
reset {
|
|
label = "Reset button";
|
|
linux,code = <KEY_RESTART>;
|
|
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
|
|
debounce-interval = <60>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&pcie {
|
|
status = "okay";
|
|
};
|
|
|
|
&spi {
|
|
status = "okay";
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <40000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x000000 0x040000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@40000 {
|
|
label = "u-boot-env";
|
|
reg = <0x040000 0x010000>;
|
|
};
|
|
|
|
partition@50000 {
|
|
label = "partition-table";
|
|
reg = <0x050000 0x010000>;
|
|
read-only;
|
|
};
|
|
|
|
info: partition@60000 {
|
|
label = "info";
|
|
reg = <0x060000 0x010000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@70000 {
|
|
compatible = "denx,uimage";
|
|
label = "firmware";
|
|
reg = <0x070000 0xf50000>;
|
|
};
|
|
|
|
partition@fc0000 {
|
|
label = "config";
|
|
reg = <0xfc0000 0x030000>;
|
|
read-only;
|
|
};
|
|
|
|
art: partition@ff0000 {
|
|
label = "art";
|
|
reg = <0xff0000 0x010000>;
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&pinmux {
|
|
mdio_pins: mdio_pins {
|
|
/* GPIO 10 as MDIO(0x20), GPIO 8 as MDC(0x21) */
|
|
pinctrl-single,bits = <0x8 0x00200021 0x00ff00ff>;
|
|
};
|
|
};
|
|
|
|
&mdio0 {
|
|
status = "okay";
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&mdio_pins>;
|
|
|
|
phy-mask = <0x10>;
|
|
|
|
phy4: ethernet-phy@4 {
|
|
reg = <4>;
|
|
reset-gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
|
|
phy-handle = <&phy4>;
|
|
phy-mode = "sgmii";
|
|
|
|
nvmem-cells = <&macaddr_info_8>;
|
|
nvmem-cell-names = "mac-address";
|
|
|
|
qca956x-serdes-fixup;
|
|
|
|
gmac-config {
|
|
device = <&gmac>;
|
|
};
|
|
};
|
|
|
|
&info {
|
|
compatible = "nvmem-cells";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
macaddr_info_8: macaddr@8 {
|
|
reg = <0x8 0x6>;
|
|
};
|
|
};
|