ExternalVendorCode/openwrt
1
0
Fork 0
mirror of https://github.com/openwrt/openwrt.git synced 2025-01-03 12:34:19 +00:00
Code Issues Actions 7 Packages Projects Releases Wiki Activity
d61b4ecbf1
openwrt/target/linux/mediatek/image/filogic.mk
Daniel Golle 3aa686f8d4 mediatek: add support for Adtran SmartRG Bonanza Peak series 
The Bonanza Peak series are a couple of MT7986-powered 2.5 GBit/s
Wi-Fi 6 residential gateway, access point and mesh router products.

All of them come with an eMMC to boot from, are powered via USB-C and
got a USB 3.0 type-A port. All of them got a Dialog (Renesas) DA14531
Bluetooth module connected via UART. If the device was previously
running stock firmware, the BT chip's internal flash has been loaded
with firmware and it can be attached using hciattach when using
OpenWrt.

SOC: MediaTek MT7986A
RAM: 2 GiB DDR4
eMMC: 8 GiB
Bluetooth: BLE5 (DA14531)
Serial: 3.3V level, 115200 8n1 on 4-pin connector

 * SDG-8612 - Dual-band RJ-45 gateway
   2x 2.5G MaxLinear PHY for WAN port
   3x 1GE LAN ports via MT7531 switch

 * SDG-8614 - Dual-band SFP gateway
   1x SFP cage with up to 2.5G speed
   1x 2.5G MaxLinear PHY for LAN port
   3x 1GE LAN ports via MT7531 switch

 * SDG-8622 - Tri-band mesh router
   2x 2.5G MaxLinear PHY
   The MT7986 2G and 5G are used as 2G and 5G high band.
   There’s a MT7915 PCIe card for 5G low band.

 * SDG-8632 - Tri-band mesh router with 6 GHz
   2x 2.5G MaxLinear PHY
   The MT7986 serves the 2G and 6G bands.
   There’s a MT7915 PCIe card for 5G.

Installation via U-Boot serial console:
0. setup TFTP server with IP 192.168.1.10/24, place initramfs image
renamed to openwrt.XXX where XXX is the internal product number:
 SDG-8612: XXX = 412
 SDG-8614: XXX = 414
 SDG-8622: XXX = 422
 SDG-8632: XXX = 432

1. connect to the serial console and power on the device.
   Interrupt the bootloader by pressing 'st'
2. setenv boot_mode openwrt ; saveenv
3. run boot1
   Load firmware via TFTP and write to flash
4. run boot2
   Now OpenWrt initramfs should boot
5. upload sysupgrade.bin via scp to /tmp
6. sysupgrade

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-12-10 06:22:51 +00:00

915 lines
33 KiB
Makefile
Raw Blame History

DTS_DIR := $(DTS_DIR)/mediatek
define Image/Prepare
# For UBI we want only one extra block
rm -f $(KDIR)/ubi_mark
echo -ne '\xde\xad\xc0\xde' > $(KDIR)/ubi_mark
endef
define Build/mt7981-bl2
cat $(STAGING_DIR_IMAGE)/mt7981-$1-bl2.img >> $@
endef
define Build/mt7981-bl31-uboot
cat $(STAGING_DIR_IMAGE)/mt7981_$1-u-boot.fip >> $@
endef
define Build/mt7986-bl2
cat $(STAGING_DIR_IMAGE)/mt7986-$1-bl2.img >> $@
endef
define Build/mt7986-bl31-uboot
cat $(STAGING_DIR_IMAGE)/mt7986_$1-u-boot.fip >> $@
endef
define Build/mt7988-bl2
cat $(STAGING_DIR_IMAGE)/mt7988-$1-bl2.img >> $@
endef
define Build/mt7988-bl31-uboot
cat $(STAGING_DIR_IMAGE)/mt7988_$1-u-boot.fip >> $@
endef
define Build/mt798x-gpt
cp $@ $@.tmp 2>/dev/null || true
ptgen -g -o $@.tmp -a 1 -l 1024 \
$(if $(findstring sdmmc,$1), \
-H \
-t 0x83 -N bl2 -r -p 4079k@17k \
) \
-t 0x83 -N ubootenv -r -p 512k@4M \
-t 0x83 -N factory -r -p 2M@4608k \
-t 0xef -N fip -r -p 4M@6656k \
-N recovery -r -p 32M@12M \
$(if $(findstring sdmmc,$1), \
-N install -r -p 20M@44M \
-t 0x2e -N production -p $(CONFIG_TARGET_ROOTFS_PARTSIZE)M@64M \
) \
$(if $(findstring emmc,$1), \
-t 0x2e -N production -p $(CONFIG_TARGET_ROOTFS_PARTSIZE)M@64M \
)
cat $@.tmp >> $@
rm $@.tmp
endef
metadata_gl_json = \
'{ $(if $(IMAGE_METADATA),$(IMAGE_METADATA)$(comma)) \
"metadata_version": "1.1", \
"compat_version": "$(call json_quote,$(compat_version))", \
$(if $(DEVICE_COMPAT_MESSAGE),"compat_message": "$(call json_quote,$(DEVICE_COMPAT_MESSAGE))"$(comma)) \
$(if $(filter-out 1.0,$(compat_version)),"new_supported_devices": \
[$(call metadata_devices,$(SUPPORTED_DEVICES))]$(comma) \
"supported_devices": ["$(call json_quote,$(legacy_supported_message))"]$(comma)) \
$(if $(filter 1.0,$(compat_version)),"supported_devices":[$(call metadata_devices,$(SUPPORTED_DEVICES))]$(comma)) \
"version": { \
"release": "$(call json_quote,$(VERSION_NUMBER))", \
"date": "$(shell TZ='Asia/Chongqing' date '+%Y%m%d%H%M%S')", \
"dist": "$(call json_quote,$(VERSION_DIST))", \
"version": "$(call json_quote,$(VERSION_NUMBER))", \
"revision": "$(call json_quote,$(REVISION))", \
"target": "$(call json_quote,$(TARGETID))", \
"board": "$(call json_quote,$(if $(BOARD_NAME),$(BOARD_NAME),$(DEVICE_NAME)))" \
} \
}'
define Build/append-gl-metadata
$(if $(SUPPORTED_DEVICES),-echo $(call metadata_gl_json,$(SUPPORTED_DEVICES)) | fwtool -I - $@)
sha256sum "$@" | cut -d" " -f1 > "$@.sha256sum"
[ ! -s "$(BUILD_KEY)" -o ! -s "$(BUILD_KEY).ucert" -o ! -s "$@" ] || { \
cp "$(BUILD_KEY).ucert" "$@.ucert" ;\
usign -S -m "$@" -s "$(BUILD_KEY)" -x "$@.sig" ;\
ucert -A -c "$@.ucert" -x "$@.sig" ;\
fwtool -S "$@.ucert" "$@" ;\
}
endef
define Build/zyxel-nwa-fit-filogic
$(TOPDIR)/scripts/mkits-zyxel-fit-filogic.sh \
$@.its $@ "80 e1 ff ff ff ff ff ff ff ff"
PATH=$(LINUX_DIR)/scripts/dtc:$(PATH) mkimage -f $@.its $@.new
@mv $@.new $@
endef
define Build/cetron-header
$(eval magic=$(word 1,$(1)))
$(eval model=$(word 2,$(1)))
( \
dd if=/dev/zero bs=856 count=1 2>/dev/null; \
printf "$(model)," | dd bs=128 count=1 conv=sync 2>/dev/null; \
md5sum $@ | cut -f1 -d" " | dd bs=32 count=1 2>/dev/null; \
printf "$(magic)" | dd bs=4 count=1 conv=sync 2>/dev/null; \
cat $@; \
) > $@.tmp
fw_crc=$$(gzip -c $@.tmp | tail -c 8 | od -An -N4 -tx4 --endian little | tr -d ' \n'); \
printf "$$(echo $$fw_crc | sed 's/../\\x&/g')" | cat - $@.tmp > $@
rm $@.tmp
endef
define Device/acelink_ew-7886cax
DEVICE_VENDOR := Acelink
DEVICE_MODEL := EW-7886CAX
DEVICE_DTS := mt7986a-acelink-ew-7886cax
DEVICE_DTS_DIR := ../dts
DEVICE_PACKAGES := kmod-mt7986-firmware mt7986-wo-firmware
UBINIZE_OPTS := -E 5
BLOCKSIZE := 128k
PAGESIZE := 2048
IMAGE_SIZE := 65536k
KERNEL_IN_UBI := 1
IMAGES += factory.bin
IMAGE/factory.bin := append-ubi | check-size $$$$(IMAGE_SIZE)
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
endef
TARGET_DEVICES += acelink_ew-7886cax
define Device/acer_predator-w6
DEVICE_VENDOR := Acer
DEVICE_MODEL := Predator W6
DEVICE_DTS := mt7986a-acer-predator-w6
DEVICE_DTS_DIR := ../dts
DEVICE_DTS_LOADADDR := 0x47000000
DEVICE_PACKAGES := kmod-usb3 kmod-mt7986-firmware kmod-mt7916-firmware mt7986-wo-firmware e2fsprogs f2fsck mkf2fs
IMAGES := sysupgrade.bin
KERNEL := kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
KERNEL_INITRAMFS := kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
endef
TARGET_DEVICES += acer_predator-w6
define Device/adtran_smartrg
DEVICE_VENDOR := Adtran
DEVICE_DTS_DIR := ../dts
DEVICE_PACKAGES := e2fsprogs f2fsck mkf2fs kmod-hwmon-pwmfan \
kmod-mt7986-firmware mt7986-wo-firmware
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
endef
define Device/smartrg_sdg-8612
$(call Device/adtran_smartrg)
DEVICE_MODEL := SDG-8612
DEVICE_DTS := mt7986a-smartrg-SDG-8612
endef
TARGET_DEVICES += smartrg_sdg-8612
define Device/smartrg_sdg-8614
$(call Device/adtran_smartrg)
DEVICE_MODEL := SDG-8614
DEVICE_DTS := mt7986a-smartrg-SDG-8614
endef
TARGET_DEVICES += smartrg_sdg-8614
define Device/smartrg_sdg-8622
$(call Device/adtran_smartrg)
DEVICE_MODEL := SDG-8622
DEVICE_DTS := mt7986a-smartrg-SDG-8622
DEVICE_PACKAGES += kmod-mt7915-firmware
endef
TARGET_DEVICES += smartrg_sdg-8622
define Device/smartrg_sdg-8632
$(call Device/adtran_smartrg)
DEVICE_MODEL := SDG-8632
DEVICE_DTS := mt7986a-smartrg-SDG-8632
DEVICE_PACKAGES += kmod-mt7915-firmware
endef
TARGET_DEVICES += smartrg_sdg-8632
define Device/asus_tuf-ax4200
DEVICE_VENDOR := ASUS
DEVICE_MODEL := TUF-AX4200
DEVICE_DTS := mt7986a-asus-tuf-ax4200
DEVICE_DTS_DIR := ../dts
DEVICE_DTS_LOADADDR := 0x47000000
DEVICE_PACKAGES := kmod-usb3 kmod-mt7986-firmware mt7986-wo-firmware
IMAGES := sysupgrade.bin
KERNEL := kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
KERNEL_INITRAMFS := kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
endef
TARGET_DEVICES += asus_tuf-ax4200
define Device/asus_tuf-ax6000
DEVICE_VENDOR := ASUS
DEVICE_MODEL := TUF-AX6000
DEVICE_DTS := mt7986a-asus-tuf-ax6000
DEVICE_DTS_DIR := ../dts
DEVICE_DTS_LOADADDR := 0x47000000
DEVICE_PACKAGES := kmod-usb3 kmod-mt7986-firmware mt7986-wo-firmware
IMAGES := sysupgrade.bin
KERNEL := kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
KERNEL_INITRAMFS := kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
endef
TARGET_DEVICES += asus_tuf-ax6000
define Device/bananapi_bpi-r3
DEVICE_VENDOR := Bananapi
DEVICE_MODEL := BPi-R3
DEVICE_DTS := mt7986a-bananapi-bpi-r3
DEVICE_DTS_CONFIG := config-mt7986a-bananapi-bpi-r3
DEVICE_DTS_OVERLAY:= mt7986a-bananapi-bpi-r3-emmc mt7986a-bananapi-bpi-r3-nand mt7986a-bananapi-bpi-r3-nor mt7986a-bananapi-bpi-r3-sd
DEVICE_DTS_DIR := $(DTS_DIR)/
DEVICE_DTS_LOADADDR := 0x43f00000
DEVICE_PACKAGES := kmod-hwmon-pwmfan kmod-i2c-gpio kmod-mt7986-firmware kmod-sfp kmod-usb3 e2fsprogs f2fsck mkf2fs mt7986-wo-firmware
IMAGES := sysupgrade.itb
KERNEL_LOADADDR := 0x44000000
KERNEL_INITRAMFS_SUFFIX := -recovery.itb
ARTIFACTS := \
emmc-preloader.bin emmc-bl31-uboot.fip \
nor-preloader.bin nor-bl31-uboot.fip \
sdcard.img.gz \
snand-preloader.bin snand-bl31-uboot.fip
ARTIFACT/emmc-preloader.bin := mt7986-bl2 emmc-ddr4
ARTIFACT/emmc-bl31-uboot.fip := mt7986-bl31-uboot bananapi_bpi-r3-emmc
ARTIFACT/nor-preloader.bin := mt7986-bl2 nor-ddr4
ARTIFACT/nor-bl31-uboot.fip := mt7986-bl31-uboot bananapi_bpi-r3-nor
ARTIFACT/snand-preloader.bin := mt7986-bl2 spim-nand-ddr4
ARTIFACT/snand-bl31-uboot.fip := mt7986-bl31-uboot bananapi_bpi-r3-snand
ARTIFACT/sdcard.img.gz := mt798x-gpt sdmmc |\
pad-to 17k | mt7986-bl2 sdmmc-ddr4 |\
pad-to 6656k | mt7986-bl31-uboot bananapi_bpi-r3-sdmmc |\
$(if $(CONFIG_TARGET_ROOTFS_INITRAMFS),\
pad-to 12M | append-image-stage initramfs-recovery.itb | check-size 44m |\
) \
pad-to 44M | mt7986-bl2 spim-nand-ddr4 |\
pad-to 45M | mt7986-bl31-uboot bananapi_bpi-r3-snand |\
pad-to 49M | mt7986-bl2 nor-ddr4 |\
pad-to 50M | mt7986-bl31-uboot bananapi_bpi-r3-nor |\
pad-to 51M | mt7986-bl2 emmc-ddr4 |\
pad-to 52M | mt7986-bl31-uboot bananapi_bpi-r3-emmc |\
pad-to 56M | mt798x-gpt emmc |\
$(if $(CONFIG_TARGET_ROOTFS_SQUASHFS),\
pad-to 64M | append-image squashfs-sysupgrade.itb | check-size |\
) \
gzip
ifeq ($(DUMP),)
IMAGE_SIZE := $$(shell expr 64 + $$(CONFIG_TARGET_ROOTFS_PARTSIZE))m
endif
KERNEL := kernel-bin | gzip
KERNEL_INITRAMFS := kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k
IMAGE/sysupgrade.itb := append-kernel | fit gzip $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb external-static-with-rootfs | pad-rootfs | append-metadata
DEVICE_DTC_FLAGS := --pad 4096
DEVICE_COMPAT_VERSION := 1.1
DEVICE_COMPAT_MESSAGE := Device tree overlay mechanism needs bootloader update
endef
TARGET_DEVICES += bananapi_bpi-r3
define Device/cetron_ct3003
DEVICE_VENDOR := Cetron
DEVICE_MODEL := CT3003
DEVICE_DTS := mt7981b-cetron-ct3003
DEVICE_DTS_DIR := ../dts
SUPPORTED_DEVICES += mediatek,mt7981-spim-snand-rfb
DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware
UBINIZE_OPTS := -E 5
BLOCKSIZE := 128k
PAGESIZE := 2048
KERNEL_IN_UBI := 1
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
IMAGES += factory.bin
IMAGE/factory.bin := $$(IMAGE/sysupgrade.bin) | cetron-header rd30 CT3003
endef
TARGET_DEVICES += cetron_ct3003
define Device/cmcc_rax3000m
DEVICE_VENDOR := CMCC
DEVICE_MODEL := RAX3000M
DEVICE_DTS := mt7981b-cmcc-rax3000m
DEVICE_DTS_OVERLAY := mt7981b-cmcc-rax3000m-emmc mt7981b-cmcc-rax3000m-nand
DEVICE_DTS_DIR := ../dts
DEVICE_DTC_FLAGS := --pad 4096
DEVICE_DTS_LOADADDR := 0x43f00000
DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware kmod-usb3 \
e2fsprogs f2fsck mkf2fs
KERNEL_LOADADDR := 0x44000000
KERNEL := kernel-bin | gzip
KERNEL_INITRAMFS := kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k
KERNEL_INITRAMFS_SUFFIX := -recovery.itb
KERNEL_IN_UBI := 1
UBOOTENV_IN_UBI := 1
IMAGES := sysupgrade.itb
IMAGE_SIZE := $$(shell expr 64 + $$(CONFIG_TARGET_ROOTFS_PARTSIZE))m
IMAGE/sysupgrade.itb := append-kernel | \
fit gzip $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb external-static-with-rootfs | \
pad-rootfs | append-metadata
ARTIFACTS := \
emmc-gpt.bin emmc-preloader.bin emmc-bl31-uboot.fip \
nand-preloader.bin nand-bl31-uboot.fip
ARTIFACT/emmc-gpt.bin := mt798x-gpt emmc
ARTIFACT/emmc-preloader.bin := mt7981-bl2 emmc-ddr4
ARTIFACT/emmc-bl31-uboot.fip := mt7981-bl31-uboot cmcc_rax3000m-emmc
ARTIFACT/nand-preloader.bin := mt7981-bl2 spim-nand-ddr4
ARTIFACT/nand-bl31-uboot.fip := mt7981-bl31-uboot cmcc_rax3000m-nand
endef
TARGET_DEVICES += cmcc_rax3000m
define Device/confiabits_mt7981
DEVICE_VENDOR := Confiabits
DEVICE_MODEL := MT7981
DEVICE_DTS := mt7981b-confiabits-mt7981
DEVICE_DTS_DIR := ../dts
SUPPORTED_DEVICES += mediatek,mt7981-spim-snand-2500wan-gmac2-rfb
UBINIZE_OPTS := -E 5
BLOCKSIZE := 128k
PAGESIZE := 2048
IMAGE_SIZE := 65536k
KERNEL_IN_UBI := 1
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
DEVICE_PACKAGES := kmod-usb3 kmod-mt7981-firmware
endef
TARGET_DEVICES += confiabits_mt7981
define Device/cudy_wr3000-v1
DEVICE_VENDOR := Cudy
DEVICE_MODEL := WR3000
DEVICE_VARIANT := v1
DEVICE_DTS := mt7981b-cudy-wr3000-v1
DEVICE_DTS_DIR := ../dts
DEVICE_DTS_LOADADDR := 0x47000000
IMAGES := sysupgrade.bin
IMAGE_SIZE := 15424k
SUPPORTED_DEVICES += R31
KERNEL := kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
KERNEL_INITRAMFS := kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k
IMAGE/sysupgrade.bin := append-kernel | pad-to 128k | append-rootfs | pad-rootfs | check-size | append-metadata
DEVICE_PACKAGES := kmod-mt7981-firmware
endef
TARGET_DEVICES += cudy_wr3000-v1
define Device/glinet_gl-mt2500
DEVICE_VENDOR := GL.iNet
DEVICE_MODEL := GL-MT2500
DEVICE_DTS := mt7981b-glinet-gl-mt2500
DEVICE_DTS_DIR := ../dts
DEVICE_DTS_LOADADDR := 0x47000000
DEVICE_PACKAGES := -kmod-mt7915e -wpad-basic-mbedtls e2fsprogs f2fsck mkf2fs kmod-usb3
SUPPORTED_DEVICES += glinet,mt2500-emmc
IMAGES := sysupgrade.bin
IMAGE/sysupgrade.bin := sysupgrade-tar | append-gl-metadata
endef
TARGET_DEVICES += glinet_gl-mt2500
define Device/glinet_gl-mt3000
DEVICE_VENDOR := GL.iNet
DEVICE_MODEL := GL-MT3000
DEVICE_DTS := mt7981b-glinet-gl-mt3000
DEVICE_DTS_DIR := ../dts
SUPPORTED_DEVICES += glinet,mt3000-snand
DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware kmod-hwmon-pwmfan kmod-usb3
UBINIZE_OPTS := -E 5
BLOCKSIZE := 128k
PAGESIZE := 2048
IMAGE_SIZE := 246272k
KERNEL_IN_UBI := 1
IMAGE/sysupgrade.bin := sysupgrade-tar | append-gl-metadata
endef
TARGET_DEVICES += glinet_gl-mt3000
define Device/glinet_gl-mt6000
DEVICE_VENDOR := GL.iNet
DEVICE_MODEL := GL-MT6000
DEVICE_DTS := mt7986a-glinet-gl-mt6000
DEVICE_DTS_DIR := ../dts
DEVICE_PACKAGES := e2fsprogs f2fsck mkf2fs kmod-usb3 kmod-mt7986-firmware mt7986-wo-firmware
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | pad-to 32M | append-rootfs
IMAGE/sysupgrade.bin := sysupgrade-tar | append-gl-metadata
ARTIFACTS := preloader.bin bl31-uboot.fip
ARTIFACT/preloader.bin := mt7986-bl2 emmc-ddr4
ARTIFACT/bl31-uboot.fip := mt7986-bl31-uboot glinet_gl-mt6000
endef
TARGET_DEVICES += glinet_gl-mt6000
define Device/h3c_magic-nx30-pro
DEVICE_VENDOR := H3C
DEVICE_MODEL := Magic NX30 Pro
DEVICE_DTS := mt7981b-h3c-magic-nx30-pro
DEVICE_DTS_DIR := ../dts
UBINIZE_OPTS := -E 5
BLOCKSIZE := 128k
PAGESIZE := 2048
KERNEL_IN_UBI := 1
UBOOTENV_IN_UBI := 1
IMAGE_SIZE := 65536k
IMAGES := sysupgrade.itb
KERNEL_INITRAMFS_SUFFIX := -recovery.itb
KERNEL := kernel-bin | gzip
KERNEL_INITRAMFS := kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k
IMAGE/sysupgrade.itb := append-kernel | \
fit gzip $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb external-static-with-rootfs | append-metadata
DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware
ARTIFACTS := preloader.bin bl31-uboot.fip
ARTIFACT/preloader.bin := mt7981-bl2 spim-nand-ddr3
ARTIFACT/bl31-uboot.fip := mt7981-bl31-uboot h3c_magic-nx30-pro
endef
TARGET_DEVICES += h3c_magic-nx30-pro
define Device/jcg_q30-pro
DEVICE_VENDOR := JCG
DEVICE_MODEL := Q30 PRO
DEVICE_DTS := mt7981b-jcg-q30-pro
DEVICE_DTS_DIR := ../dts
UBINIZE_OPTS := -E 5
BLOCKSIZE := 128k
PAGESIZE := 2048
KERNEL_IN_UBI := 1
UBOOTENV_IN_UBI := 1
IMAGES := sysupgrade.itb
KERNEL_INITRAMFS_SUFFIX := -recovery.itb
KERNEL := kernel-bin | gzip
KERNEL_INITRAMFS := kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k
IMAGE/sysupgrade.itb := append-kernel | \
fit gzip $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb external-static-with-rootfs | append-metadata
DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware
ARTIFACTS := preloader.bin bl31-uboot.fip
ARTIFACT/preloader.bin := mt7981-bl2 spim-nand-ddr3
ARTIFACT/bl31-uboot.fip := mt7981-bl31-uboot jcg_q30-pro
endef
TARGET_DEVICES += jcg_q30-pro
define Device/mediatek_mt7981-rfb
DEVICE_VENDOR := MediaTek
DEVICE_MODEL := MT7981 rfb
DEVICE_DTS := mt7981-rfb
DEVICE_DTS_OVERLAY:= \
mt7981-rfb-spim-nand \
mt7981-rfb-mxl-2p5g-phy-eth1 \
mt7981-rfb-mxl-2p5g-phy-swp5
DEVICE_DTS_DIR := $(DTS_DIR)/
DEVICE_DTC_FLAGS := --pad 4096
DEVICE_DTS_LOADADDR := 0x43f00000
DEVICE_PACKAGES := kmod-mt7981-firmware kmod-usb3 e2fsprogs f2fsck mkf2fs mt7981-wo-firmware
KERNEL_LOADADDR := 0x44000000
KERNEL := kernel-bin | gzip
KERNEL_INITRAMFS := kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k
KERNEL_INITRAMFS_SUFFIX := .itb
KERNEL_IN_UBI := 1
UBOOTENV_IN_UBI := 1
IMAGES := sysupgrade.itb
IMAGE_SIZE := $$(shell expr 64 + $$(CONFIG_TARGET_ROOTFS_PARTSIZE))m
IMAGE/sysupgrade.itb := append-kernel | fit gzip $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb external-with-rootfs | pad-rootfs | append-metadata
ARTIFACTS := \
emmc-preloader.bin emmc-bl31-uboot.fip \
nor-preloader.bin nor-bl31-uboot.fip \
sdcard.img.gz \
snfi-nand-preloader.bin snfi-nand-bl31-uboot.fip \
spim-nand-preloader.bin spim-nand-bl31-uboot.fip
ARTIFACT/emmc-preloader.bin := mt7981-bl2 emmc-ddr3
ARTIFACT/emmc-bl31-uboot.fip := mt7981-bl31-uboot rfb-emmc
ARTIFACT/nor-preloader.bin := mt7981-bl2 nor-ddr3
ARTIFACT/nor-bl31-uboot.fip := mt7981-bl31-uboot rfb-emmc
ARTIFACT/snfi-nand-preloader.bin := mt7981-bl2 snand-ddr3
ARTIFACT/snfi-nand-bl31-uboot.fip := mt7981-bl31-uboot rfb-snfi
ARTIFACT/spim-nand-preloader.bin := mt7981-bl2 spim-nand-ddr3
ARTIFACT/spim-nand-bl31-uboot.fip := mt7981-bl31-uboot rfb-spim-nand
ARTIFACT/sdcard.img.gz := mt798x-gpt sdmmc |\
pad-to 17k | mt7981-bl2 sdmmc-ddr3 |\
pad-to 6656k | mt7981-bl31-uboot rfb-sd |\
$(if $(CONFIG_TARGET_ROOTFS_INITRAMFS),\
pad-to 12M | append-image-stage initramfs.itb | check-size 44m |\
) \
pad-to 44M | mt7981-bl2 spim-nand-ddr3 |\
pad-to 45M | mt7981-bl31-uboot rfb-spim-nand |\
pad-to 49M | mt7981-bl2 nor-ddr3 |\
pad-to 50M | mt7981-bl31-uboot rfb-nor |\
pad-to 51M | mt7981-bl2 snand-ddr3 |\
pad-to 53M | mt7981-bl31-uboot rfb-snfi |\
$(if $(CONFIG_TARGET_ROOTFS_SQUASHFS),\
pad-to 64M | append-image squashfs-sysupgrade.itb | check-size |\
) \
gzip
endef
TARGET_DEVICES += mediatek_mt7981-rfb
define Device/mediatek_mt7986a-rfb-nand
DEVICE_VENDOR := MediaTek
DEVICE_MODEL := MT7986 rfba AP (NAND)
DEVICE_DTS := mt7986a-rfb-spim-nand
DEVICE_DTS_DIR := $(DTS_DIR)/
DEVICE_PACKAGES := kmod-mt7986-firmware mt7986-wo-firmware
SUPPORTED_DEVICES := mediatek,mt7986a-rfb-snand
UBINIZE_OPTS := -E 5
BLOCKSIZE := 128k
PAGESIZE := 2048
IMAGE_SIZE := 65536k
KERNEL_IN_UBI := 1
IMAGES += factory.bin
IMAGE/factory.bin := append-ubi | check-size $$$$(IMAGE_SIZE)
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
KERNEL = kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
KERNEL_INITRAMFS = kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd
endef
TARGET_DEVICES += mediatek_mt7986a-rfb-nand
define Device/mediatek_mt7986b-rfb
DEVICE_VENDOR := MediaTek
DEVICE_MODEL := MTK7986 rfbb AP
DEVICE_DTS := mt7986b-rfb
DEVICE_DTS_DIR := $(DTS_DIR)/
DEVICE_PACKAGES := kmod-mt7986-firmware mt7986-wo-firmware
SUPPORTED_DEVICES := mediatek,mt7986b-rfb
UBINIZE_OPTS := -E 5
BLOCKSIZE := 128k
PAGESIZE := 2048
IMAGE_SIZE := 65536k
KERNEL_IN_UBI := 1
IMAGES += factory.bin
IMAGE/factory.bin := append-ubi | check-size $$$$(IMAGE_SIZE)
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
endef
TARGET_DEVICES += mediatek_mt7986b-rfb
define Device/mediatek_mt7988a-rfb
DEVICE_VENDOR := MediaTek
DEVICE_MODEL := MT7988A rfb
DEVICE_DTS := mt7988a-rfb
DEVICE_DTS_OVERLAY:= \
mt7988a-rfb-emmc \
mt7988a-rfb-sd \
mt7988a-rfb-snfi-nand \
mt7988a-rfb-spim-nand \
mt7988a-rfb-spim-nor \
mt7988a-rfb-eth1-aqr \
mt7988a-rfb-eth1-i2p5g-phy \
mt7988a-rfb-eth1-mxl \
mt7988a-rfb-eth1-sfp \
mt7988a-rfb-eth2-aqr \
mt7988a-rfb-eth2-mxl \
mt7988a-rfb-eth2-sfp
DEVICE_DTS_DIR := $(DTS_DIR)/
DEVICE_DTC_FLAGS := --pad 4096
DEVICE_DTS_LOADADDR := 0x45f00000
DEVICE_PACKAGES := kmod-sfp
KERNEL_LOADADDR := 0x46000000
KERNEL := kernel-bin | gzip
KERNEL_INITRAMFS := kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k
KERNEL_INITRAMFS_SUFFIX := .itb
KERNEL_IN_UBI := 1
IMAGE_SIZE := $$(shell expr 64 + $$(CONFIG_TARGET_ROOTFS_PARTSIZE))m
IMAGES := sysupgrade.itb
IMAGE/sysupgrade.itb := append-kernel | fit gzip $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb external-with-rootfs | pad-rootfs | append-metadata
ARTIFACTS := \
emmc-gpt.bin emmc-preloader.bin emmc-bl31-uboot.fip \
nor-preloader.bin nor-bl31-uboot.fip \
sdcard.img.gz \
snand-preloader.bin snand-bl31-uboot.fip
ARTIFACT/emmc-gpt.bin := mt798x-gpt emmc
ARTIFACT/emmc-preloader.bin := mt7988-bl2 emmc-comb
ARTIFACT/emmc-bl31-uboot.fip := mt7988-bl31-uboot rfb-emmc
ARTIFACT/nor-preloader.bin := mt7988-bl2 nor-comb
ARTIFACT/nor-bl31-uboot.fip := mt7988-bl31-uboot rfb-nor
ARTIFACT/snand-preloader.bin := mt7988-bl2 spim-nand-comb
ARTIFACT/snand-bl31-uboot.fip := mt7988-bl31-uboot rfb-snand
ARTIFACT/sdcard.img.gz := mt798x-gpt sdmmc |\
pad-to 17k | mt7988-bl2 sdmmc-comb |\
pad-to 6656k | mt7988-bl31-uboot rfb-sd |\
$(if $(CONFIG_TARGET_ROOTFS_INITRAMFS),\
pad-to 12M | append-image-stage initramfs.itb | check-size 44m |\
) \
pad-to 44M | mt7988-bl2 spim-nand-comb |\
pad-to 45M | mt7988-bl31-uboot rfb-snand |\
pad-to 51M | mt7988-bl2 nor-comb |\
pad-to 51M | mt7988-bl31-uboot rfb-nor |\
pad-to 55M | mt7988-bl2 emmc-comb |\
pad-to 56M | mt7988-bl31-uboot rfb-emmc |\
pad-to 62M | mt798x-gpt emmc |\
$(if $(CONFIG_TARGET_ROOTFS_SQUASHFS),\
pad-to 64M | append-image squashfs-sysupgrade.itb | check-size |\
) \
gzip
endef
TARGET_DEVICES += mediatek_mt7988a-rfb
define Device/mercusys_mr90x-v1
DEVICE_VENDOR := MERCUSYS
DEVICE_MODEL := MR90X v1
DEVICE_DTS := mt7986b-mercusys-mr90x-v1
DEVICE_DTS_DIR := ../dts
DEVICE_PACKAGES := kmod-mt7986-firmware mt7986-wo-firmware
UBINIZE_OPTS := -E 5
BLOCKSIZE := 128k
PAGESIZE := 2048
IMAGE_SIZE := 51200k
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
endef
TARGET_DEVICES += mercusys_mr90x-v1
define Device/netgear_wax220
DEVICE_VENDOR := NETGEAR
DEVICE_MODEL := WAX220
DEVICE_DTS := mt7986b-netgear-wax220
DEVICE_DTS_DIR := ../dts
NETGEAR_ENC_MODEL := WAX220
NETGEAR_ENC_REGION := US
DEVICE_PACKAGES := kmod-mt7986-firmware mt7986-wo-firmware
KERNEL_INITRAMFS_SUFFIX := -recovery.itb
IMAGE_SIZE := 32768k
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
IMAGES += factory.img
# Padding to 10M seems to be required by OEM web interface
IMAGE/factory.img := sysupgrade-tar | \
pad-to 10M | check-size | netgear-encrypted-factory
endef
TARGET_DEVICES += netgear_wax220
define Device/qihoo_360t7
DEVICE_VENDOR := Qihoo
DEVICE_MODEL := 360T7
DEVICE_DTS := mt7981b-qihoo-360t7
DEVICE_DTS_DIR := ../dts
UBINIZE_OPTS := -E 5
BLOCKSIZE := 128k
PAGESIZE := 2048
KERNEL_IN_UBI := 1
UBOOTENV_IN_UBI := 1
IMAGES := sysupgrade.itb
KERNEL_INITRAMFS_SUFFIX := -recovery.itb
KERNEL := kernel-bin | gzip
KERNEL_INITRAMFS := kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k
IMAGE/sysupgrade.itb := append-kernel | \
fit gzip $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb external-static-with-rootfs | append-metadata
DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware
ARTIFACTS := preloader.bin bl31-uboot.fip
ARTIFACT/preloader.bin := mt7981-bl2 spim-nand-ddr3
ARTIFACT/bl31-uboot.fip := mt7981-bl31-uboot qihoo_360t7
endef
TARGET_DEVICES += qihoo_360t7
define Device/tplink_tl-xdr-common
DEVICE_VENDOR := TP-Link
DEVICE_DTS_DIR := ../dts
UBINIZE_OPTS := -E 5
BLOCKSIZE := 128k
PAGESIZE := 2048
KERNEL_IN_UBI := 1
UBOOTENV_IN_UBI := 1
IMAGES := sysupgrade.itb
KERNEL_INITRAMFS_SUFFIX := -recovery.itb
KERNEL := kernel-bin | gzip
KERNEL_INITRAMFS := kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k
IMAGE/sysupgrade.itb := append-kernel | \
fit gzip $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb external-with-rootfs | append-metadata
DEVICE_PACKAGES := kmod-usb3 kmod-mt7986-firmware mt7986-wo-firmware
ARTIFACTS := preloader.bin bl31-uboot.fip
ARTIFACT/preloader.bin := mt7986-bl2 spim-nand-ddr3
endef
define Device/tplink_tl-xdr4288
DEVICE_MODEL := TL-XDR4288
DEVICE_DTS := mt7986a-tplink-tl-xdr4288
ARTIFACT/bl31-uboot.fip := mt7986-bl31-uboot tplink_tl-xdr4288
$(call Device/tplink_tl-xdr-common)
endef
TARGET_DEVICES += tplink_tl-xdr4288
define Device/tplink_tl-xdr6086
DEVICE_MODEL := TL-XDR6086
DEVICE_DTS := mt7986a-tplink-tl-xdr6086
ARTIFACT/bl31-uboot.fip := mt7986-bl31-uboot tplink_tl-xdr6086
$(call Device/tplink_tl-xdr-common)
endef
TARGET_DEVICES += tplink_tl-xdr6086
define Device/tplink_tl-xdr6088
DEVICE_MODEL := TL-XDR6088
DEVICE_DTS := mt7986a-tplink-tl-xdr6088
ARTIFACT/bl31-uboot.fip := mt7986-bl31-uboot tplink_tl-xdr6088
$(call Device/tplink_tl-xdr-common)
endef
TARGET_DEVICES += tplink_tl-xdr6088
define Device/ubnt_unifi-6-plus
DEVICE_VENDOR := Ubiquiti
DEVICE_MODEL := UniFi 6 Plus
DEVICE_DTS := mt7981a-ubnt-unifi-6-plus
DEVICE_DTS_DIR := ../dts
DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware e2fsprogs f2fsck mkf2fs fdisk partx-utils
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
endef
TARGET_DEVICES += ubnt_unifi-6-plus
define Device/xiaomi_mi-router-wr30u-112m-nmbm
DEVICE_VENDOR := Xiaomi
DEVICE_MODEL := Mi Router WR30U (112M UBI with NMBM-Enabled layout)
DEVICE_DTS := mt7981b-xiaomi-mi-router-wr30u-112m-nmbm
DEVICE_DTS_DIR := ../dts
UBINIZE_OPTS := -E 5
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware
ifneq ($(CONFIG_TARGET_ROOTFS_INITRAMFS),)
ARTIFACTS := initramfs-factory.ubi
ARTIFACT/initramfs-factory.ubi := append-image-stage initramfs-kernel.bin | ubinize-kernel
endif
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
endef
TARGET_DEVICES += xiaomi_mi-router-wr30u-112m-nmbm
define Device/xiaomi_mi-router-wr30u-stock
DEVICE_VENDOR := Xiaomi
DEVICE_MODEL := Mi Router WR30U (stock layout)
DEVICE_DTS := mt7981b-xiaomi-mi-router-wr30u-stock
DEVICE_DTS_DIR := ../dts
UBINIZE_OPTS := -E 5
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware
ifneq ($(CONFIG_TARGET_ROOTFS_INITRAMFS),)
ARTIFACTS := initramfs-factory.ubi
ARTIFACT/initramfs-factory.ubi := append-image-stage initramfs-kernel.bin | ubinize-kernel
endif
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
endef
TARGET_DEVICES += xiaomi_mi-router-wr30u-stock
define Device/xiaomi_mi-router-wr30u-ubootmod
DEVICE_VENDOR := Xiaomi
DEVICE_MODEL := Mi Router WR30U (OpenWrt U-Boot layout)
DEVICE_DTS := mt7981b-xiaomi-mi-router-wr30u-ubootmod
DEVICE_DTS_DIR := ../dts
UBINIZE_OPTS := -E 5
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware
KERNEL_IN_UBI := 1
UBOOTENV_IN_UBI := 1
IMAGES := sysupgrade.itb
KERNEL_INITRAMFS_SUFFIX := -recovery.itb
KERNEL := kernel-bin | gzip
KERNEL_INITRAMFS := kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k
IMAGE/sysupgrade.itb := append-kernel | \
fit gzip $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb external-static-with-rootfs | append-metadata
ARTIFACTS := preloader.bin bl31-uboot.fip
ARTIFACT/preloader.bin := mt7981-bl2 spim-nand-ddr3
ARTIFACT/bl31-uboot.fip := mt7981-bl31-uboot xiaomi_mi-router-wr30u
ifneq ($(CONFIG_TARGET_ROOTFS_INITRAMFS),)
ARTIFACTS += initramfs-factory.ubi
ARTIFACT/initramfs-factory.ubi := append-image-stage initramfs-recovery.itb | ubinize-kernel
endif
endef
TARGET_DEVICES += xiaomi_mi-router-wr30u-ubootmod
define Device/xiaomi_redmi-router-ax6000-stock
DEVICE_VENDOR := Xiaomi
DEVICE_MODEL := Redmi Router AX6000 (stock layout)
DEVICE_DTS := mt7986a-xiaomi-redmi-router-ax6000-stock
DEVICE_DTS_DIR := ../dts
DEVICE_PACKAGES := kmod-leds-ws2812b kmod-mt7986-firmware mt7986-wo-firmware
UBINIZE_OPTS := -E 5
BLOCKSIZE := 128k
PAGESIZE := 2048
ifneq ($(CONFIG_TARGET_ROOTFS_INITRAMFS),)
ARTIFACTS := initramfs-factory.ubi
ARTIFACT/initramfs-factory.ubi := append-image-stage initramfs-kernel.bin | ubinize-kernel
endif
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
endef
TARGET_DEVICES += xiaomi_redmi-router-ax6000-stock
define Device/xiaomi_redmi-router-ax6000-ubootmod
DEVICE_VENDOR := Xiaomi
DEVICE_MODEL := Redmi Router AX6000 (OpenWrt U-Boot layout)
DEVICE_DTS := mt7986a-xiaomi-redmi-router-ax6000-ubootmod
DEVICE_DTS_DIR := ../dts
DEVICE_PACKAGES := kmod-leds-ws2812b kmod-mt7986-firmware mt7986-wo-firmware
KERNEL_INITRAMFS_SUFFIX := -recovery.itb
IMAGES := sysupgrade.itb
UBINIZE_OPTS := -E 5
BLOCKSIZE := 128k
PAGESIZE := 2048
KERNEL_IN_UBI := 1
UBOOTENV_IN_UBI := 1
KERNEL := kernel-bin | gzip
KERNEL_INITRAMFS := kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k
IMAGE/sysupgrade.itb := append-kernel | \
fit gzip $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb external-static-with-rootfs | append-metadata
ARTIFACTS := preloader.bin bl31-uboot.fip
ARTIFACT/preloader.bin := mt7986-bl2 spim-nand-ddr4
ARTIFACT/bl31-uboot.fip := mt7986-bl31-uboot xiaomi_redmi-router-ax6000
ifneq ($(CONFIG_TARGET_ROOTFS_INITRAMFS),)
ARTIFACTS += initramfs-factory.ubi
ARTIFACT/initramfs-factory.ubi := append-image-stage initramfs-recovery.itb | ubinize-kernel
endif
endef
TARGET_DEVICES += xiaomi_redmi-router-ax6000-ubootmod
define Device/zbtlink_zbt-z8102ax
DEVICE_VENDOR := Zbtlink
DEVICE_MODEL := ZBT-Z8102AX
DEVICE_DTS := mt7981b-zbtlink-zbt-z8102ax
DEVICE_DTS_DIR := ../dts
DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware kmod-usb3 kmod-usb-net-qmi-wwan kmod-usb-serial-option
KERNEL_IN_UBI := 1
UBINIZE_OPTS := -E 5
BLOCKSIZE := 128k
PAGESIZE := 2048
IMAGE_SIZE := 65536k
IMAGES += factory.bin
IMAGE/factory.bin := append-ubi | check-size $$(IMAGE_SIZE)
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
endef
TARGET_DEVICES += zbtlink_zbt-z8102ax
define Device/zyxel_ex5601-t0-stock
DEVICE_VENDOR := Zyxel
DEVICE_MODEL := EX5601-T0
DEVICE_VARIANT := (stock layout)
DEVICE_DTS := mt7986a-zyxel-ex5601-t0-stock
DEVICE_DTS_DIR := ../dts
DEVICE_PACKAGES := kmod-mt7986-firmware mt7986-wo-firmware kmod-usb3
SUPPORTED_DEVICES := mediatek,mt7986a-rfb-snand
UBINIZE_OPTS := -E 5
BLOCKSIZE := 256k
PAGESIZE := 4096
IMAGE_SIZE := 65536k
KERNEL_IN_UBI := 1
IMAGES += factory.bin
IMAGE/factory.bin := append-ubi | check-size $$$$(IMAGE_SIZE)
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
KERNEL = kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
KERNEL_INITRAMFS = kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd
endef
TARGET_DEVICES += zyxel_ex5601-t0-stock
define Device/zyxel_ex5601-t0-ubootmod
DEVICE_VENDOR := Zyxel
DEVICE_MODEL := EX5601-T0
DEVICE_VARIANT := (OpenWrt U-Boot layout)
DEVICE_DTS := mt7986a-zyxel-ex5601-t0-ubootmod
DEVICE_DTS_DIR := ../dts
DEVICE_PACKAGES := kmod-mt7986-firmware mt7986-wo-firmware kmod-usb3
KERNEL_INITRAMFS_SUFFIX := -recovery.itb
IMAGES := sysupgrade.itb
UBINIZE_OPTS := -E 5
BLOCKSIZE := 256k
PAGESIZE := 4096
KERNEL_IN_UBI := 1
UBOOTENV_IN_UBI := 1
KERNEL := kernel-bin | lzma
KERNEL_INITRAMFS := kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd
IMAGE/sysupgrade.itb := append-kernel | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb external-static-with-rootfs | append-metadata
ARTIFACTS := preloader.bin bl31-uboot.fip
ARTIFACT/preloader.bin := mt7986-bl2 spim-nand-4k-ddr4
ARTIFACT/bl31-uboot.fip := mt7986-bl31-uboot zyxel_ex5601-t0
ifneq ($(CONFIG_TARGET_ROOTFS_INITRAMFS),)
ARTIFACTS += initramfs-factory.ubi
ARTIFACT/initramfs-factory.ubi := append-image-stage initramfs-recovery.itb | ubinize-kernel
endif
endef
TARGET_DEVICES += zyxel_ex5601-t0-ubootmod
define Device/zyxel_ex5700-telenor
DEVICE_VENDOR := ZyXEL
DEVICE_MODEL := EX5700 (Telenor)
DEVICE_DTS := mt7986a-zyxel-ex5700-telenor
DEVICE_DTS_DIR := ../dts
DEVICE_PACKAGES := kmod-mt7916-firmware kmod-ubootenv-nvram kmod-usb3 kmod-mt7986-firmware mt7986-wo-firmware
UBINIZE_OPTS := -E 5
BLOCKSIZE := 128k
PAGESIZE := 2048
IMAGE_SIZE := 65536k
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
endef
TARGET_DEVICES += zyxel_ex5700-telenor
define Device/zyxel_nwa50ax-pro
DEVICE_VENDOR := ZyXEL
DEVICE_MODEL := NWA50AX Pro
DEVICE_DTS := mt7981b-zyxel-nwa50ax-pro
DEVICE_DTS_DIR := ../dts
DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware zyxel-bootconfig
DEVICE_DTS_LOADADDR := 0x44000000
UBINIZE_OPTS := -E 5
BLOCKSIZE := 128k
PAGESIZE := 2048
IMAGE_SIZE := 51200k
KERNEL_IN_UBI := 1
IMAGES += factory.bin
IMAGE/factory.bin := append-ubi | check-size $$$$(IMAGE_SIZE) | zyxel-nwa-fit-filogic
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
endef
TARGET_DEVICES += zyxel_nwa50ax-pro
Reference in New Issue View Git Blame Copy Permalink