mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-22 06:57:57 +00:00
3d6cbe287a
The WLR-1230 (ZX-5207) is an AC1200 Wave 2 outdoor repeater with sector antennas for wall or pole mounting. The device is manufactured by Todaair and meant to be used with a tuya-based app, there is no webinterface for configuration. Specifications: - MT7628AN, 8 MiB SPI NOR flash, 64 MiB RAM, 2x2 802.11n - MT7613 2x2 802.11ac Wave 2 - 802.3af PoE or 12V 1A 5.5x2.1 power supply (included) - 3 LEDs WLAN, LAN, RES; PWR LED is not software-controllable TFTP installation: - rename sysupgrade to `firmware_auto.bin` - provide at 192.168.1.10 during boot HTTP installation: - keep reset button pressed for 5 seconds during power on (LEDs flash slowly, then quickly to confirm, then remain steady on) - recovery web interface is at 192.168.1.1, upload sysupgrade Opening the device - two screws are located in the bottom left and right corners underneath the label, inner tray slides out easily initramfs boot - open device, connect serial console (pins are labelled) - keep pressing `4` during second tftp attempt to enter uboot shell - run `tftpboot 82000000` to avoid memory overlap, then `bootm` Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
131 lines
2.0 KiB
Plaintext
131 lines
2.0 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
/dts-v1/;
|
|
|
|
#include "mt7628an.dtsi"
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
#include <dt-bindings/leds/common.h>
|
|
|
|
/ {
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
reset {
|
|
label = "reset";
|
|
gpios = <&gpio 38 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_RESTART>;
|
|
};
|
|
};
|
|
|
|
chosen {
|
|
bootargs = "console=ttyS0,115200";
|
|
};
|
|
};
|
|
|
|
&spi0 {
|
|
status = "okay";
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <50000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x0 0x30000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@30000 {
|
|
label = "u-boot-env";
|
|
reg = <0x30000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@40000 {
|
|
label = "factory";
|
|
reg = <0x40000 0x10000>;
|
|
read-only;
|
|
|
|
nvmem-layout {
|
|
compatible = "fixed-layout";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
eeprom_factory_0: eeprom@0 {
|
|
reg = <0x0 0x400>;
|
|
};
|
|
|
|
macaddr_factory_4: macaddr@4 {
|
|
reg = <0x4 0x6>;
|
|
};
|
|
|
|
eeprom_factory_8000: eeprom@8000 {
|
|
reg = <0x8000 0x4da8>;
|
|
};
|
|
};
|
|
};
|
|
|
|
partition@50000 {
|
|
label = "firmware";
|
|
reg = <0x50000 0x7b0000>;
|
|
compatible = "denx,uimage";
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&state_default {
|
|
gpio {
|
|
groups = "gpio", "refclk", "wdt", "wled_an";
|
|
function = "gpio";
|
|
};
|
|
};
|
|
|
|
&pcie {
|
|
status = "okay";
|
|
};
|
|
|
|
&pcie0 {
|
|
wifi@0,0 {
|
|
compatible = "mediatek,mt76";
|
|
reg = <0x0000 0 0 0 0>;
|
|
ieee80211-freq-limit = <5000000 6000000>;
|
|
nvmem-cells = <&eeprom_factory_8000>;
|
|
nvmem-cell-names = "eeprom";
|
|
};
|
|
};
|
|
|
|
ðernet {
|
|
nvmem-cells = <&macaddr_factory_4>;
|
|
nvmem-cell-names = "mac-address";
|
|
};
|
|
|
|
&esw {
|
|
mediatek,portdisable = <0x2f>;
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
nvmem-cells = <&eeprom_factory_0>;
|
|
nvmem-cell-names = "eeprom";
|
|
};
|
|
|
|
&usbphy {
|
|
status = "disabled";
|
|
};
|
|
|
|
&ehci {
|
|
status = "disabled";
|
|
};
|
|
|
|
&ohci {
|
|
status = "disabled";
|
|
};
|
|
|