mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-22 15:02:32 +00:00
31a6605de0
Serge Vasilugin reports: To improve mt7620 built-in wifi performance some changes: 1. Correct BW20/BW40 switching (see comments with mark (1)) 2. Correct TX_SW_CFG1 MAC reg from v3 of vendor driver see https://gitlab.com/dm38/padavan-ng/-/blob/master/trunk/proprietary/rt_wifi/rtpci/3.0.X.X/mt76x2/chips/rt6352.c#L531 3. Set bbp66 for all chains. 4. US_CYC_CNT init based on Programming guide, default value was 33 (pci), set chipset bus clock with fallback to cpu clock/3. 5. Don't overwrite default values for mt7620. 6. Correct some typos. 7. Add support for external LNA: a) RF and BBP regs never be corrected for this mode b) eLNA is driven the same way as ePA with mt7620's pin PA but vendor driver explicitly pin PA to gpio mode (for forrect calibration?) so I'm not sure that request for pa_pin in dts-file will be enough First 5 changes (really 2) improve performance for boards w/o eLNA/ePA. Changes 7 add support for eLNA Configuration w/o eLAN/ePA and with eLNA show results tx/rx (from router point of view) for each stream: 35-40/30-35 Mbps for HT20 65-70/60-65 Mbps for HT40 Yes. Max results for 2T2R client is 140-145/135-140 with peaks 160/150, It correspond to mediatek driver results. Boards with ePA untested. Reported-by: Serge Vasilugin <vasilugin@yandex.ru> Signed-off-by: Daniel Golle <daniel@makrotopia.org>
613 lines
10 KiB
Plaintext
613 lines
10 KiB
Plaintext
/dts-v1/;
|
|
|
|
/ {
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
compatible = "ralink,mt7620a-soc";
|
|
|
|
aliases {
|
|
spi0 = &spi0;
|
|
spi1 = &spi1;
|
|
serial0 = &uartlite;
|
|
};
|
|
|
|
cpus {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
cpu@0 {
|
|
compatible = "mips,mips24KEc";
|
|
reg = <0>;
|
|
};
|
|
};
|
|
|
|
chosen {
|
|
bootargs = "console=ttyS0,57600";
|
|
};
|
|
|
|
cpuintc: cpuintc {
|
|
#address-cells = <0>;
|
|
#interrupt-cells = <1>;
|
|
interrupt-controller;
|
|
compatible = "mti,cpu-interrupt-controller";
|
|
};
|
|
|
|
palmbus: palmbus@10000000 {
|
|
compatible = "palmbus";
|
|
reg = <0x10000000 0x200000>;
|
|
ranges = <0x0 0x10000000 0x1FFFFF>;
|
|
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
sysc: sysc@0 {
|
|
compatible = "ralink,mt7620a-sysc", "ralink,rt3050-sysc", "syscon";
|
|
reg = <0x0 0x100>;
|
|
};
|
|
|
|
timer: timer@100 {
|
|
compatible = "ralink,mt7620a-timer", "ralink,rt2880-timer";
|
|
reg = <0x100 0x20>;
|
|
|
|
interrupt-parent = <&intc>;
|
|
interrupts = <1>;
|
|
};
|
|
|
|
watchdog: watchdog@120 {
|
|
compatible = "ralink,mt7620a-wdt", "ralink,rt2880-wdt";
|
|
reg = <0x120 0x10>;
|
|
|
|
resets = <&rstctrl 8>;
|
|
reset-names = "wdt";
|
|
|
|
interrupt-parent = <&intc>;
|
|
interrupts = <1>;
|
|
};
|
|
|
|
intc: intc@200 {
|
|
compatible = "ralink,mt7620a-intc", "ralink,rt2880-intc";
|
|
reg = <0x200 0x100>;
|
|
|
|
resets = <&rstctrl 19>;
|
|
reset-names = "intc";
|
|
|
|
interrupt-controller;
|
|
#interrupt-cells = <1>;
|
|
|
|
interrupt-parent = <&cpuintc>;
|
|
interrupts = <2>;
|
|
};
|
|
|
|
memc: memc@300 {
|
|
compatible = "ralink,mt7620a-memc", "ralink,rt3050-memc";
|
|
reg = <0x300 0x100>;
|
|
|
|
resets = <&rstctrl 20>;
|
|
reset-names = "mc";
|
|
|
|
interrupt-parent = <&intc>;
|
|
interrupts = <3>;
|
|
};
|
|
|
|
uart: uart@500 {
|
|
compatible = "ralink,mt7620a-uart", "ralink,rt2880-uart", "ns16550a";
|
|
reg = <0x500 0x100>;
|
|
|
|
resets = <&rstctrl 12>;
|
|
reset-names = "uart";
|
|
|
|
interrupt-parent = <&intc>;
|
|
interrupts = <5>;
|
|
|
|
reg-shift = <2>;
|
|
|
|
status = "disabled";
|
|
};
|
|
|
|
gpio0: gpio@600 {
|
|
compatible = "ralink,mt7620a-gpio", "ralink,rt2880-gpio";
|
|
reg = <0x600 0x34>;
|
|
|
|
resets = <&rstctrl 13>;
|
|
reset-names = "pio";
|
|
|
|
interrupt-parent = <&intc>;
|
|
interrupts = <6>;
|
|
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
|
|
ngpios = <24>;
|
|
ralink,gpio-base = <0>;
|
|
ralink,register-map = [ 00 04 08 0c
|
|
20 24 28 2c
|
|
30 34 ];
|
|
};
|
|
|
|
gpio1: gpio@638 {
|
|
compatible = "ralink,mt7620a-gpio", "ralink,rt2880-gpio";
|
|
reg = <0x638 0x24>;
|
|
|
|
interrupt-parent = <&intc>;
|
|
interrupts = <6>;
|
|
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
|
|
ngpios = <16>;
|
|
ralink,gpio-base = <24>;
|
|
ralink,register-map = [ 00 04 08 0c
|
|
10 14 18 1c
|
|
20 24 ];
|
|
|
|
status = "disabled";
|
|
};
|
|
|
|
gpio2: gpio@660 {
|
|
compatible = "ralink,mt7620a-gpio", "ralink,rt2880-gpio";
|
|
reg = <0x660 0x24>;
|
|
|
|
interrupt-parent = <&intc>;
|
|
interrupts = <6>;
|
|
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
|
|
ngpios = <32>;
|
|
ralink,gpio-base = <40>;
|
|
ralink,register-map = [ 00 04 08 0c
|
|
10 14 18 1c
|
|
20 24 ];
|
|
|
|
status = "disabled";
|
|
};
|
|
|
|
gpio3: gpio@688 {
|
|
compatible = "ralink,mt7620a-gpio", "ralink,rt2880-gpio";
|
|
reg = <0x688 0x24>;
|
|
|
|
interrupt-parent = <&intc>;
|
|
interrupts = <6>;
|
|
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
|
|
ngpios = <1>;
|
|
ralink,gpio-base = <72>;
|
|
ralink,register-map = [ 00 04 08 0c
|
|
10 14 18 1c
|
|
20 24 ];
|
|
|
|
status = "disabled";
|
|
};
|
|
|
|
i2c: i2c@900 {
|
|
compatible = "ralink,rt2880-i2c";
|
|
reg = <0x900 0x100>;
|
|
|
|
resets = <&rstctrl 16>;
|
|
reset-names = "i2c";
|
|
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
status = "disabled";
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&i2c_pins>;
|
|
};
|
|
|
|
i2s: i2s@a00 {
|
|
compatible = "mediatek,mt7620-i2s";
|
|
reg = <0xa00 0x100>;
|
|
|
|
resets = <&rstctrl 17>;
|
|
reset-names = "i2s";
|
|
|
|
interrupt-parent = <&intc>;
|
|
interrupts = <10>;
|
|
|
|
txdma-req = <2>;
|
|
rxdma-req = <3>;
|
|
|
|
dmas = <&gdma 4>,
|
|
<&gdma 6>;
|
|
dma-names = "tx", "rx";
|
|
|
|
status = "disabled";
|
|
};
|
|
|
|
spi0: spi@b00 {
|
|
compatible = "ralink,mt7620a-spi", "ralink,rt2880-spi";
|
|
reg = <0xb00 0x40>;
|
|
|
|
resets = <&rstctrl 18>;
|
|
reset-names = "spi";
|
|
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
status = "disabled";
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&spi_pins>;
|
|
};
|
|
|
|
spi1: spi@b40 {
|
|
compatible = "ralink,rt2880-spi";
|
|
reg = <0xb40 0x60>;
|
|
|
|
resets = <&rstctrl 18>;
|
|
reset-names = "spi";
|
|
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
status = "disabled";
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&spi_cs1>;
|
|
};
|
|
|
|
uartlite: uartlite@c00 {
|
|
compatible = "ralink,mt7620a-uart", "ralink,rt2880-uart", "ns16550a";
|
|
reg = <0xc00 0x100>;
|
|
|
|
resets = <&rstctrl 19>;
|
|
reset-names = "uartl";
|
|
|
|
interrupt-parent = <&intc>;
|
|
interrupts = <12>;
|
|
|
|
reg-shift = <2>;
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&uartlite_pins>;
|
|
};
|
|
|
|
systick: systick@d00 {
|
|
compatible = "ralink,mt7620a-systick", "ralink,cevt-systick";
|
|
reg = <0xd00 0x10>;
|
|
|
|
resets = <&rstctrl 28>;
|
|
reset-names = "intc";
|
|
|
|
interrupt-parent = <&cpuintc>;
|
|
interrupts = <7>;
|
|
};
|
|
|
|
pcm: pcm@2000 {
|
|
compatible = "ralink,mt7620a-pcm";
|
|
reg = <0x2000 0x800>;
|
|
|
|
resets = <&rstctrl 11>;
|
|
reset-names = "pcm";
|
|
|
|
interrupt-parent = <&intc>;
|
|
interrupts = <4>;
|
|
|
|
status = "disabled";
|
|
};
|
|
|
|
gdma: gdma@2800 {
|
|
compatible = "ralink,mt7620a-gdma", "ralink,rt3883-gdma";
|
|
reg = <0x2800 0x800>;
|
|
|
|
resets = <&rstctrl 14>;
|
|
reset-names = "dma";
|
|
|
|
interrupt-parent = <&intc>;
|
|
interrupts = <7>;
|
|
|
|
#dma-cells = <1>;
|
|
#dma-channels = <16>;
|
|
#dma-requests = <16>;
|
|
|
|
status = "disabled";
|
|
};
|
|
};
|
|
|
|
pinctrl: pinctrl {
|
|
compatible = "ralink,rt2880-pinmux";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&state_default>;
|
|
|
|
state_default: pinctrl0 {
|
|
};
|
|
|
|
pcm_i2s_pins: pcm_i2s {
|
|
pcm_i2s {
|
|
groups = "uartf";
|
|
function = "pcm i2s";
|
|
};
|
|
};
|
|
|
|
uartf_gpio_pins: uartf_gpio {
|
|
uartf_gpio {
|
|
groups = "uartf";
|
|
function = "gpio uartf";
|
|
};
|
|
};
|
|
|
|
gpio_i2s_pins: gpio_i2s {
|
|
gpio_i2s {
|
|
groups = "uartf";
|
|
function = "gpio i2s";
|
|
};
|
|
};
|
|
|
|
spi_pins: spi_pins {
|
|
spi_pins {
|
|
groups = "spi";
|
|
function = "spi";
|
|
};
|
|
};
|
|
|
|
spi_cs1: spi1 {
|
|
spi1 {
|
|
groups = "spi refclk";
|
|
function = "spi refclk";
|
|
};
|
|
};
|
|
|
|
i2c_pins: i2c_pins {
|
|
i2c_pins {
|
|
groups = "i2c";
|
|
function = "i2c";
|
|
};
|
|
};
|
|
|
|
uartlite_pins: uartlite {
|
|
uart {
|
|
groups = "uartlite";
|
|
function = "uartlite";
|
|
};
|
|
};
|
|
|
|
mdio_pins: mdio {
|
|
mdio {
|
|
groups = "mdio";
|
|
function = "mdio";
|
|
};
|
|
};
|
|
|
|
mdio_refclk_pins: mdio_refclk {
|
|
mdio_refclk {
|
|
groups = "mdio";
|
|
function = "refclk";
|
|
};
|
|
};
|
|
|
|
ephy_pins: ephy {
|
|
ephy {
|
|
groups = "ephy";
|
|
function = "ephy";
|
|
};
|
|
};
|
|
|
|
wled_pins: wled {
|
|
wled {
|
|
groups = "wled";
|
|
function = "wled";
|
|
};
|
|
};
|
|
|
|
rgmii1_pins: rgmii1 {
|
|
rgmii1 {
|
|
groups = "rgmii1";
|
|
function = "rgmii1";
|
|
};
|
|
};
|
|
|
|
rgmii2_pins: rgmii2 {
|
|
rgmii2 {
|
|
groups = "rgmii2";
|
|
function = "rgmii2";
|
|
};
|
|
};
|
|
|
|
pcie_pins: pcie {
|
|
pcie {
|
|
groups = "pcie";
|
|
function = "pcie rst";
|
|
};
|
|
};
|
|
|
|
pa_pins: pa {
|
|
pa {
|
|
groups = "pa";
|
|
function = "pa";
|
|
};
|
|
};
|
|
|
|
pa_gpio_pins: pa_gpio {
|
|
pa {
|
|
groups = "pa";
|
|
function = "gpio";
|
|
};
|
|
};
|
|
|
|
sdhci_pins: sdhci {
|
|
sdhci {
|
|
groups = "nd_sd";
|
|
function = "sd";
|
|
};
|
|
};
|
|
};
|
|
|
|
rstctrl: rstctrl {
|
|
compatible = "ralink,mt7620a-reset", "ralink,rt2880-reset";
|
|
#reset-cells = <1>;
|
|
};
|
|
|
|
clkctrl: clkctrl {
|
|
compatible = "ralink,rt2880-clock";
|
|
#clock-cells = <1>;
|
|
};
|
|
|
|
usbphy: usbphy {
|
|
compatible = "mediatek,mt7620-usbphy";
|
|
#phy-cells = <0>;
|
|
|
|
ralink,sysctl = <&sysc>;
|
|
resets = <&rstctrl 22 &rstctrl 25>;
|
|
reset-names = "host", "device";
|
|
|
|
clocks = <&clkctrl 22 &clkctrl 25>;
|
|
clock-names = "host", "device";
|
|
};
|
|
|
|
ethernet: ethernet@10100000 {
|
|
compatible = "mediatek,mt7620-eth";
|
|
reg = <0x10100000 0x10000>;
|
|
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
interrupt-parent = <&cpuintc>;
|
|
interrupts = <5>;
|
|
|
|
resets = <&rstctrl 21 &rstctrl 23>;
|
|
reset-names = "fe", "esw";
|
|
|
|
mediatek,switch = <&gsw>;
|
|
|
|
port@4 {
|
|
compatible = "mediatek,mt7620a-gsw-port", "mediatek,eth-port";
|
|
reg = <4>;
|
|
|
|
status = "disabled";
|
|
};
|
|
|
|
port@5 {
|
|
compatible = "mediatek,mt7620a-gsw-port", "mediatek,eth-port";
|
|
reg = <5>;
|
|
|
|
status = "disabled";
|
|
};
|
|
|
|
mdio-bus {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
status = "disabled";
|
|
};
|
|
};
|
|
|
|
gsw: gsw@10110000 {
|
|
compatible = "mediatek,mt7620-gsw";
|
|
reg = <0x10110000 0x8000>;
|
|
|
|
resets = <&rstctrl 23>;
|
|
reset-names = "esw";
|
|
|
|
interrupt-parent = <&intc>;
|
|
interrupts = <17>;
|
|
};
|
|
|
|
sdhci: sdhci@10130000 {
|
|
compatible = "ralink,mt7620-sdhci";
|
|
reg = <0x10130000 0x4000>;
|
|
|
|
interrupt-parent = <&intc>;
|
|
interrupts = <14>;
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&sdhci_pins>;
|
|
|
|
status = "disabled";
|
|
};
|
|
|
|
ehci: ehci@101c0000 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
compatible = "generic-ehci";
|
|
reg = <0x101c0000 0x1000>;
|
|
|
|
interrupt-parent = <&intc>;
|
|
interrupts = <18>;
|
|
|
|
phys = <&usbphy>;
|
|
phy-names = "usb";
|
|
|
|
status = "disabled";
|
|
|
|
ehci_port1: port@1 {
|
|
reg = <1>;
|
|
#trigger-source-cells = <0>;
|
|
};
|
|
};
|
|
|
|
ohci: ohci@101c1000 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
compatible = "generic-ohci";
|
|
reg = <0x101c1000 0x1000>;
|
|
|
|
interrupt-parent = <&intc>;
|
|
interrupts = <18>;
|
|
|
|
phys = <&usbphy>;
|
|
phy-names = "usb";
|
|
|
|
status = "disabled";
|
|
|
|
ohci_port1: port@1 {
|
|
reg = <1>;
|
|
#trigger-source-cells = <0>;
|
|
};
|
|
};
|
|
|
|
pcie: pcie@10140000 {
|
|
compatible = "mediatek,mt7620-pci";
|
|
reg = <0x10140000 0x100
|
|
0x10142000 0x100>;
|
|
|
|
#address-cells = <3>;
|
|
#size-cells = <2>;
|
|
|
|
resets = <&rstctrl 26>;
|
|
reset-names = "pcie0";
|
|
|
|
clocks = <&clkctrl 26>;
|
|
clock-names = "pcie0";
|
|
|
|
interrupt-parent = <&cpuintc>;
|
|
interrupts = <4>;
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pcie_pins>;
|
|
|
|
device_type = "pci";
|
|
|
|
bus-range = <0 255>;
|
|
ranges = <
|
|
0x02000000 0 0x00000000 0x20000000 0 0x10000000 /* pci memory */
|
|
0x01000000 0 0x00000000 0x10160000 0 0x00010000 /* io space */
|
|
>;
|
|
|
|
status = "disabled";
|
|
|
|
pcie0: pcie@0,0 {
|
|
reg = <0x0000 0 0 0 0>;
|
|
|
|
#address-cells = <3>;
|
|
#size-cells = <2>;
|
|
|
|
device_type = "pci";
|
|
|
|
ranges;
|
|
};
|
|
};
|
|
|
|
wmac: wmac@10180000 {
|
|
compatible = "ralink,rt7620-wmac", "ralink,rt2880-wmac";
|
|
reg = <0x10180000 0x40000>;
|
|
|
|
interrupt-parent = <&cpuintc>;
|
|
interrupts = <6>;
|
|
|
|
ralink,eeprom = "soc_wmac.eeprom";
|
|
};
|
|
};
|