openwrt/target/linux/ramips/dts/WN-AC1167GR.dts
INAGAKI Hiroshi f305ce5c35 ramips: add support for I-O DATA WN-AC1167GR
I-O DATA WN-AC1167GR is a 2.4/5 GHz band 11ac router, based on
MediaTek MT7620A.

Specification:

- SoC     : MediaTek MT7620A
- RAM     : DDR2 64 MB
- Flash   : SPI-NOR 8MB
- WLAN    : 2.4/5 GHz, 2T2R
  - 2.4 GHz: MT7620A (SoC)
  - 5 GHz  : MT7612E
- Ethernet: 10/100/1000 Mbps (ext. MT7530)
- LED/key : 4x/3x (2x buttons, 1x slide-switch)
- UART    : through-hole on PCB
  - J2: TX, GND, RX, Vcc from SoC side
  - 115200n8

Flash instruction using factory image:

1. Boot WN-AC1167GR normaly
2. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
3. Select the OpenWrt factory image and click update ("更新") button
to perform firmware update
4. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2019-02-14 16:56:14 +01:00

217 lines
3.4 KiB
Plaintext

// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;
#include "mt7620a.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
/ {
compatible = "iodata,wn-ac1167gr", "ralink,mt7620a-soc";
model = "I-O DATA WN-AC1167GR";
aliases {
led-boot = &led_power;
led-failsafe = &led_power;
led-running = &led_power;
led-upgrade = &led_power;
};
memory@0 {
device_type = "memory";
reg = <0x0 0x4000000>;
};
leds {
compatible = "gpio-leds";
led_power: power {
label = "wn-ac1167gr:green:power";
gpios = <&gpio0 7 GPIO_ACTIVE_LOW>;
default-state = "on";
};
wlan2g {
label = "wn-ac1167gr:green:wlan2g";
gpios = <&gpio0 10 GPIO_ACTIVE_LOW>;
};
notification {
label = "wn-ac1167gr:green:notification";
gpios = <&gpio0 11 GPIO_ACTIVE_LOW>;
};
wlan5g {
label = "wn-ac1167gr:green:wlan5g";
gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
};
};
keys {
compatible = "gpio-keys-polled";
poll-interval = <20>;
wps {
label = "wps";
gpios = <&gpio0 1 GPIO_ACTIVE_LOW>;
linux,code = <KEY_WPS_BUTTON>;
};
reset {
label = "reset";
gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
};
auto {
label = "auto";
gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
linux,code = <BTN_0>;
linux,input-type = <EV_SW>;
};
};
};
&spi0 {
status = "okay";
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <10000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "u-boot";
reg = <0x0 0x30000>;
read-only;
};
partition@30000 {
label = "u-boot-env";
reg = <0x30000 0x10000>;
read-only;
};
Factory: partition@40000 {
label = "Factory";
reg = <0x40000 0x8000>;
read-only;
};
iNIC_rf: partition@48000 {
label = "iNIC_rf";
reg = <0x48000 0x8000>;
read-only;
};
partition@50000 {
label = "NoUsed";
reg = <0x50000 0x20000>;
read-only;
};
partition@70000 {
compatible = "denx,uimage";
label = "firmware";
reg = <0x70000 0x6b4000>;
};
partition@724000 {
label = "manufacture";
reg = <0x724000 0x8c000>;
read-only;
};
partition@7b0000 {
label = "backup";
reg = <0x7b0000 0x10000>;
read-only;
};
partition@7c0000 {
label = "storage";
reg = <0x7c0000 0x40000>;
read-only;
};
};
};
};
&ethernet {
pinctrl-names = "default";
pinctrl-0 = <&rgmii1_pins &mdio_pins>;
mtd-mac-address = <&Factory 0x4>;
port@5 {
status = "okay";
mediatek,fixed-link = <1000 1 1 1>;
phy-mode = "rgmii";
};
mdio-bus {
#address-cells = <1>;
#size-cells = <0>;
status = "okay";
ethernet-phy@0 {
reg = <0>;
phy-mode = "rgmii";
};
ethernet-phy@1 {
reg = <1>;
phy-mode = "rgmii";
};
ethernet-phy@2 {
reg = <2>;
phy-mode = "rgmii";
};
ethernet-phy@3 {
reg = <3>;
phy-mode = "rgmii";
};
ethernet-phy@4 {
reg = <4>;
phy-mode = "rgmii";
};
ethernet-phy@1f {
reg = <0x1f>;
phy-mode = "rgmii";
};
};
};
&pinctrl {
state_default: pinctrl0 {
gpio {
ralink,group = "i2c", "uartf";
ralink,function = "gpio";
};
};
};
&pcie {
status = "okay";
};
&pcie0 {
wifi@0,0 {
reg = <0x0000 0 0 0 0>;
mediatek,mtd-eeprom = <&iNIC_rf 0x0>;
ieee80211-freq-limit = <5000000 6000000>;
};
};
&wmac {
ralink,mtd-eeprom = <&Factory 0x0>;
};