Tianling Shen d3c193525e mediatek: add CMCC RAX3000M support ... Hardware specification: SoC: MediaTek MT7981B 2x A53 Flash: 64GB eMMC or 128 MB SPI-NAND RAM: 512MB Ethernet: 4x 10/100/1000 Mbps Switch: MediaTek MT7531AE WiFi: MediaTek MT7976C Button: Reset, Mesh Power: DC 12V 1A - UART: 3.3v, 115200n8 -------------------------- | Layout | | ----------------- | | 4 | GND TX VCC RX | <= | | ----------------- | -------------------------- Gain SSH access: 1. Login into web interface, and download the configuration. 2. Enter fakeroot, decompress the configuration: tar -zxf cfg_export_config_file.conf 3. Edit 'etc/config/dropbear', set 'enable' to '1'. 4. Edit 'etc/shadow', update (remove) root password: 'root::19523:0:99999:7:::' 5. Repack 'etc' directory: tar -zcf cfg_export_config_file.conf etc/ * If you find an error about 'etc/wireless/mediatek/DBDC_card0.dat', just ignore it. 6. Upload new configuration via web interface, now you can SSH to RAX3000M. Check stroage type: Check the label on the back of the device: "CH EC CMIIT ID: xxxx" is eMMC version "CH CMIIT ID: xxxx" is NAND version eMMC Flash instructions: 1. SSH to RAX3000M, and backup everything, especially 'factory' part. ('data' partition can be ignored, it's useless.) 2. Write new GPT table: dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-gpt.bin of=/dev/mmcblk0 bs=512 seek=0 count=34 conv=fsync 3. Erase and write new BL2: echo 0 > /sys/block/mmcblk0boot0/force_ro dd if=/dev/zero of=/dev/mmcblk0boot0 bs=512 count=8192 conv=fsync dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-preloader.bin of=/dev/mmcblk0boot0 bs=512 conv=fsync 4. Erase and write new FIP: dd if=/dev/zero of=/dev/mmcblk0 bs=512 seek=13312 count=8192 conv=fsync dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-bl31-uboot.fip of=/dev/mmcblk0 bs=512 seek=13312 conv=fsync 5. Set static IP on your PC: IP 192.168.1.254, GW 192.168.1.1 6. Serve OpenWrt initramfs image using TFTP server. 7. Cut off the power and re-engage, wait for TFTP recovery to complete. 8. After OpenWrt has booted, perform sysupgrade. 9. Additionally, if you want to have eMMC recovery boot feature: (Don't worry! You will always have TFTP recovery boot feature.) dd if=openwrt-mediatek-filogic-cmcc_rax3000m-initramfs-recovery.itb of=/dev/mmcblk0p4 bs=512 conv=fsync NAND Flash instructions: 1. SSH to RAX3000M, and backup everything, especially 'Factory' part. 2. Erase and write new BL2: mtd erase BL2 mtd write openwrt-mediatek-filogic-cmcc_rax3000m-nand-preloader.bin BL2 3. Erase and write new FIP: mtd erase FIP mtd write openwrt-mediatek-filogic-cmcc_rax3000m-nand-bl31-uboot.fip FIP 4. Set static IP on your PC: IP 192.168.1.254, GW 192.168.1.1 5. Serve OpenWrt initramfs image using TFTP server. 6. Cut off the power and re-engage, wait for TFTP recovery to complete. 7. After OpenWrt has booted, erase UBI volumes: ubidetach -p /dev/mtd0 ubiformat -y /dev/mtd0 ubiattach -p /dev/mtd0 8. Create new ubootenv volumes: ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB 9. Additionally, if you want to have NAND recovery boot feature: (Don't worry! You will always have TFTP recovery boot feature.) ubimkvol /dev/ubi0 -n 2 -N recovery -s 20MiB ubiupdatevol /dev/ubi0_2 openwrt-mediatek-filogic-cmcc_rax3000m-initramfs-recovery.itb 10. Perform sysupgrade. Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org> (cherry picked from commit 423186d7d8) [rebased to 23.05] Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>		2023-11-07 00:46:00 +01:00
..
11_fix_wifi_mac	mediatek: add CMCC RAX3000M support	2023-11-07 00:46:00 +01:00