mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-30 18:47:06 +00:00
8961d2268e
This converts all remaining devices to use interrupt-driven gpio-keys compatible instead of gpio-keys-polled. The poll-interval is removed. Only ar7240_netgear_wnr612-v2 is kept at gpio-keys-polled, as this one is using ath9k keys. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Tested-by: Karl Palsson <karlp@etactica.com> Tested-by: Dmitry Tunin <hanipouspilot@gmail.com>
174 lines
2.8 KiB
Plaintext
174 lines
2.8 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
/dts-v1/;
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
#include "qca956x.dtsi"
|
|
|
|
/ {
|
|
compatible = "avm,fritz4020", "qca,qca9560";
|
|
model = "AVM FRITZ!Box 4020";
|
|
|
|
aliases {
|
|
led-boot = &power;
|
|
led-failsafe = &info_red;
|
|
led-running = &power;
|
|
led-upgrade = &info_red;
|
|
};
|
|
|
|
chosen {
|
|
bootargs = "console=ttyS0,115200n8";
|
|
};
|
|
|
|
led_spi {
|
|
compatible = "spi-gpio";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
sck-gpios = <&gpio 20 GPIO_ACTIVE_HIGH>;
|
|
mosi-gpios = <&gpio 19 GPIO_ACTIVE_HIGH>;
|
|
num-chipselects = <0>;
|
|
|
|
led_gpio: led_gpio@0 {
|
|
compatible = "fairchild,74hc595";
|
|
reg = <0>;
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
registers-number = <1>;
|
|
spi-max-frequency = <10000000>;
|
|
|
|
gpio_latch_bit {
|
|
gpio-hog;
|
|
gpios = <7 GPIO_ACTIVE_HIGH>;
|
|
output-high;
|
|
line-name = "gpio-latch-bit";
|
|
};
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
power: power {
|
|
label = "fritz4020:green:power";
|
|
gpios = <&led_gpio 2 GPIO_ACTIVE_LOW>;
|
|
default-state = "on";
|
|
};
|
|
|
|
wlan {
|
|
label = "fritz4020:green:wlan";
|
|
gpios = <&led_gpio 3 GPIO_ACTIVE_LOW>;
|
|
linux,default-trigger = "phy0tpt";
|
|
};
|
|
|
|
lan {
|
|
label = "fritz4020:green:lan";
|
|
gpios = <&led_gpio 0 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
wan {
|
|
label = "fritz4020:green:wan";
|
|
gpios = <&led_gpio 4 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
info {
|
|
label = "fritz4020:green:info";
|
|
gpios = <&led_gpio 6 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
info_red: info_red {
|
|
label = "fritz4020:red:info";
|
|
gpios = <&led_gpio 1 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
wps_button {
|
|
label = "WPS button";
|
|
linux,code = <KEY_WPS_BUTTON>;
|
|
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
wlan_button {
|
|
label = "WLAN button";
|
|
linux,code = <KEY_RFKILL>;
|
|
gpios = <&gpio 21 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&uart {
|
|
status = "okay";
|
|
};
|
|
|
|
&gpio {
|
|
status = "okay";
|
|
};
|
|
|
|
&spi {
|
|
status = "okay";
|
|
num-cs = <1>;
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <25000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "urlader";
|
|
reg = <0x000000 0x020000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@1 {
|
|
compatible = "avm,eva-firmware";
|
|
label = "firmware";
|
|
reg = <0x020000 0xee0000>;
|
|
};
|
|
|
|
partition@2 {
|
|
label = "tffs (1)";
|
|
reg = <0xf00000 0x080000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@3 {
|
|
label = "tffs (2)";
|
|
reg = <0xf80000 0x080000>;
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
|
|
phy-mode = "mii";
|
|
phy-handle = <&swphy0>;
|
|
|
|
gmac-config {
|
|
device = <&gmac>;
|
|
|
|
switch-phy-addr-swap = <1>;
|
|
switch-phy-swap = <1>;
|
|
};
|
|
};
|
|
|
|
ð1 {
|
|
status = "okay";
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
qca,no-eeprom;
|
|
};
|