mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-30 18:47:06 +00:00
cb3cd52694
Hardware
--------
CPU: Qualcomm Atheros QCA9558
RAM: 128M DDR2
FLASH: 16MiB
ETH: 1x Atheros AR8035 (PoE in)
WiFi2: QCA9558 3T3R
WiFi5: QCA9880 3T3R
BTN: 1x Reset
LED: 1x LED Power (non-controllable)
1x LED Status (internal)
1x LED LAN (controlled by PHY)
1x LED WLAN
BEEP: 1x GPIO attached piezo beeper
UART: 3.3V GND TX RX (115200-N-8) (3.3V is square pad)
Header is located next to external-LED header.
Installation
------------
Make sure you set a password for the root user as prompted on first
setup!
1. Upload OpenWRT sysupgrade image via SSH to the device.
Use /tmp as the destination folder on the device.
User is root, password the one set in the web interface.
2. Install OpenWRT with
> sysupgrade -n -F /tmp/<openwrt-image-name>
Signed-off-by: David Bauer <mail@david-bauer.net>
54 lines
1008 B
Plaintext
54 lines
1008 B
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
/dts-v1/;
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
#include "qca9558_devolo_dvl1xxx.dtsi"
|
|
|
|
/ {
|
|
compatible = "devolo,dvl1750x", "qca,qca9558";
|
|
model = "devolo WiFi pro 1750x";
|
|
|
|
aliases {
|
|
led-boot = &status_red;
|
|
led-failsafe = &status_red;
|
|
led-running = &status_red;
|
|
led-upgrade = &status_red;
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
status_red: status_red {
|
|
/* This LED is not visible on the external casing. */
|
|
label = "dvl1750x:red:status";
|
|
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
wlan {
|
|
label = "dvl1750x:green:wlan";
|
|
gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
|
|
linux,default-trigger = "phy0tpt";
|
|
};
|
|
};
|
|
|
|
beeper {
|
|
compatible = "gpio-beeper";
|
|
gpios = <&gpio 17 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
};
|
|
|
|
ð0 {
|
|
pll-data = <0xbe000000 0x80000101 0x80001313>;
|
|
phy-mode = "rgmii-id";
|
|
};
|
|
|
|
&gmac_config {
|
|
rxdv-delay = <3>;
|
|
rxd-delay = <3>;
|
|
txen-delay = <3>;
|
|
txd-delay = <3>;
|
|
rgmii-enabled = <1>;
|
|
};
|