mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-28 01:28:59 +00:00
23ac1ad951
General hardware info:
----------------------
D-Link DGS-1210-28P rev. F1 is a switch with 24 ethernet ports and 4
combo ports, all ports Gbit capable. It is based on a RTL8382 SoC
@500MHz, DRAM 128MB and 32MB flash. 24 ethernet ports are 802.3af/at PoE
capable with a total PoE power budget of 193W.
Power over Ethernet:
--------------------
The PSE hardware consists of three BCM59121 PSE chips, serving 8 ports
each. They are controlled by a Nuvoton MCU. In order to enable PoE, the
realtek-poe package is required. It is installed by default, but
currently it requires the manual editing of /etc/config/poe. Keep in
mind that the port number assignment does not match on this switch,
alway 8 ports are in reversed order: 8-1, 16-9 and 24-17.
LEDs and Buttons:
-----------------
On stock firmware, the mode button is supposed to switch the LED
indicators of all port LEDs between Link Activity and PoE status. The
currently selected mode is visualized using the respective LEDs. PoE Max
indicates that the maximum PoE budget has been reached. Since there is
currently no support for this behavior, these LEDs and the mode button
can be used independently.
Serial connection:
------------------
The UART for the SoC (115200 8N1) is available via unpopulated standard
0.1" pin header marked J6. Pin1 is marked with arrow and square.
Pin 1: Vcc 3.3V
Pin 2: Tx
Pin 3: Rx
Pin 4: Gnd
OEM installation from Web Interface:
------------------------------------
1. Make sure you are booting using OEM in image 2 slot. If not,
switch to
image2 using the menus
System > Firmware Information > Boot from image2
Tools > reboot
2. Upload image in vendor firmware via Tools > Backup / Upgrade
Firmware > image1
3. Toggle startup image via System > Firmware Information > Boot
from
image1
4. Tools > reboot
Other installation methods not tested, but since the device shares the
board with the DGS-1210-28, the following should work:
Boot initramfs image from U-Boot:
---------------------------------
1. Press Escape key during `Hit Esc key to stop autoboot` prompt
2. Press CTRL+C keys to get into real U-Boot prompt
3. Init network with `rtk network on` command
4. Load image with `tftpboot 0x8f000000
openwrt-rtl838x-generic-d-link_dgs-1210-28p-f-initramfs-kernel.bin`
command
5. Boot the image with `bootm` command
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15938
Signed-off-by: Sander Vanheule <sander@svanheule.net>
27 lines
572 B
Plaintext
27 lines
572 B
Plaintext
#
|
|
# Copyright (C) 2024 openwrt.org
|
|
#
|
|
|
|
. /lib/functions.sh
|
|
|
|
board=$(board_name)
|
|
|
|
case "$board" in
|
|
d-link,dgs-1210-28p-f|d-link,dgs-1210-28mp-f)
|
|
# Enable fan control
|
|
FAN_CTRL='/sys/class/hwmon/hwmon0'
|
|
echo 1 > "$FAN_PATH/pwm1_enable"
|
|
|
|
# Set fan script execution in crontab
|
|
grep -s -q fan_ctrl.sh /etc/crontabs/root && exit 0
|
|
|
|
echo "# dlink fan script runs every 5 minutes" >> /etc/crontabs/root
|
|
echo "*/5 * * * * /sbin/fan_ctrl.sh" >> /etc/crontabs/root
|
|
|
|
# Execute one time after initial flash (instead of waiting 5 min for cron)
|
|
/sbin/fan_ctrl.sh
|
|
;;
|
|
esac
|
|
|
|
exit 0
|