mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-20 14:13:16 +00:00
f2f42a54e8
The qca8k patch series brings the numbering to 799. This patch renames 7xx patches to create space for more backports to be added. Signed-off-by: Matthew Hagan <mnhagan88@gmail.com> [rename 729->719] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
86 lines
3.4 KiB
Diff
86 lines
3.4 KiB
Diff
From 9d5ef190e5615a7b63af89f88c4106a5bc127974 Mon Sep 17 00:00:00 2001
|
|
From: Vladimir Oltean <vladimir.oltean@nxp.com>
|
|
Date: Fri, 5 Feb 2021 15:37:10 +0200
|
|
Subject: [PATCH] net: dsa: automatically bring up DSA master when opening user
|
|
port
|
|
|
|
DSA wants the master interface to be open before the user port is due to
|
|
historical reasons. The promiscuity of interfaces that are down used to
|
|
have issues, as referenced Lennert Buytenhek in commit df02c6ff2e39
|
|
("dsa: fix master interface allmulti/promisc handling").
|
|
|
|
The bugfix mentioned there, commit b6c40d68ff64 ("net: only invoke
|
|
dev->change_rx_flags when device is UP"), was basically a "don't do
|
|
that" approach to working around the promiscuity while down issue.
|
|
|
|
Further work done by Vlad Yasevich in commit d2615bf45069 ("net: core:
|
|
Always propagate flag changes to interfaces") has resolved the
|
|
underlying issue, and it is strictly up to the DSA and 8021q drivers
|
|
now, it is no longer mandated by the networking core that the master
|
|
interface must be up when changing its promiscuity.
|
|
|
|
From DSA's point of view, deciding to error out in dsa_slave_open
|
|
because the master isn't up is
|
|
(a) a bad user experience and
|
|
(b) knocking at an open door.
|
|
Even if there still was an issue with promiscuity while down, DSA could
|
|
still just open the master and avoid it.
|
|
|
|
Doing it this way has the additional benefit that user space can now
|
|
remove DSA-specific workarounds, like systemd-networkd with BindCarrier:
|
|
https://github.com/systemd/systemd/issues/7478
|
|
|
|
And we can finally remove one of the 2 bullets in the "Common pitfalls
|
|
using DSA setups" chapter.
|
|
|
|
Tested with two cascaded DSA switches:
|
|
|
|
$ ip link set sw0p2 up
|
|
fsl_enetc 0000:00:00.2 eno2: configuring for fixed/internal link mode
|
|
fsl_enetc 0000:00:00.2 eno2: Link is Up - 1Gbps/Full - flow control rx/tx
|
|
mscc_felix 0000:00:00.5 swp0: configuring for fixed/sgmii link mode
|
|
mscc_felix 0000:00:00.5 swp0: Link is Up - 1Gbps/Full - flow control off
|
|
8021q: adding VLAN 0 to HW filter on device swp0
|
|
sja1105 spi2.0 sw0p2: configuring for phy/rgmii-id link mode
|
|
IPv6: ADDRCONF(NETDEV_CHANGE): eno2: link becomes ready
|
|
IPv6: ADDRCONF(NETDEV_CHANGE): swp0: link becomes ready
|
|
|
|
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
|
|
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
|
|
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
---
|
|
Documentation/networking/dsa/dsa.rst | 4 ----
|
|
net/dsa/slave.c | 7 +++++--
|
|
2 files changed, 5 insertions(+), 6 deletions(-)
|
|
|
|
--- a/Documentation/networking/dsa/dsa.rst
|
|
+++ b/Documentation/networking/dsa/dsa.rst
|
|
@@ -273,10 +273,6 @@ will not make us go through the switch t
|
|
the Ethernet switch on the other end, expecting a tag will typically drop this
|
|
frame.
|
|
|
|
-Slave network devices check that the master network device is UP before allowing
|
|
-you to administratively bring UP these slave network devices. A common
|
|
-configuration mistake is forgetting to bring UP the master network device first.
|
|
-
|
|
Interactions with other subsystems
|
|
==================================
|
|
|
|
--- a/net/dsa/slave.c
|
|
+++ b/net/dsa/slave.c
|
|
@@ -68,8 +68,11 @@ static int dsa_slave_open(struct net_dev
|
|
struct dsa_port *dp = dsa_slave_to_port(dev);
|
|
int err;
|
|
|
|
- if (!(master->flags & IFF_UP))
|
|
- return -ENETDOWN;
|
|
+ err = dev_open(master, NULL);
|
|
+ if (err < 0) {
|
|
+ netdev_err(dev, "failed to open master %s\n", master->name);
|
|
+ goto out;
|
|
+ }
|
|
|
|
if (!ether_addr_equal(dev->dev_addr, master->dev_addr)) {
|
|
err = dev_uc_add(master, dev->dev_addr);
|