mirror of
https://github.com/openwrt/openwrt.git
synced 2025-04-20 09:02:06 +00:00
cd09f26660
Hardware: * SoC: Qualcomm Atheros QCA9558 * RAM: 256MB * Flash: 16MB SPI NOR * Ethernet: 2x 10/100/1000 (1x 802.3at PoE-PD) * WiFi 2.4GHz: Qualcomm Atheros QCA9558 * WiFi 5GHz: Qualcomm Ahteros QCA9880-2R4E * LEDS: 1x 5GHz, 1x 2.4GHz, 1x LAN1(POE), 1x LAN2, 1x POWER * Buttons: 1x RESET * UART: 1x RJ45 RS-232 Console port Installation via stock firmware: * Install the factory image via the stock firmware web interface Installation via bootloader Emergency Web Server: * Connect your PC to the LAN1(PoE) port * Configure your PC with IP address 192.168.0.90 * Open a serial console to the Console port (115200,8n1) * Press "q" within 2s when "press 'q' to stop autoboot" appears * Open http://192.168.0.50 in a browser * Upload either the factory or the sysupgrade image * Once you see "write image into flash...OK,dest addr=0x9f070000" you can power-cycle the device. Ignore "checksum bad" messages. Setting the MAC addresses for the ethernet interfaces via /etc/board.d/02_network adds the following snippets to /etc/config/network: config device 'lan_eth0_1_dev' option name 'eth0.1' option macaddr 'xx:xx:xx:xx:xx:xx' config device 'wan_eth1_2_dev' option name 'eth1.2' option macaddr 'xx:xx:xx:xx:xx:xx' This would result in the proper MAC addresses being set for the VLAN subinterfaces, but the parent interfaces would still have a random MAC address. Using untagged VLANs could solve this, but would still leave those extra snippets in /etc/config/network, and then the device VLAN setup would differ from the one used in ar71xx. Therefore, the MAC addresses of the ethernet interfaces are being set via preinit instead. The bdcfg partition contains 4 MAC address labels: - lanmac - wanmac - wlanmac - wlanmac_a The first 3 all contain the same MAC address, which is also the one on the label. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
This is the buildsystem for the OpenWrt Linux distribution.
To build your own firmware you need a Linux, BSD or MacOSX system (case
sensitive filesystem required). Cygwin is unsupported because of the lack
of a case sensitive file system.
You need gcc, binutils, bzip2, flex, python3.5+, perl, make, find, grep, diff,
unzip, gawk, getopt, subversion, libz-dev and libc headers installed.
1. Run "./scripts/feeds update -a" to obtain all the latest package definitions
defined in feeds.conf / feeds.conf.default
2. Run "./scripts/feeds install -a" to install symlinks for all obtained
packages into package/feeds/
3. Run "make menuconfig" to select your preferred configuration for the
toolchain, target system & firmware packages.
4. Run "make" to build your firmware. This will download all sources, build
the cross-compile toolchain and then cross-compile the Linux kernel & all
chosen applications for your target system.
Sunshine!
Your OpenWrt Community
http://www.openwrt.org