mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-26 17:01:14 +00:00
c6ddf8d502
Many changes were done in drivers/pinctrl/bcm/pinctrl-bcm2835.c between
5.4.171 and 5.4.179.
The following 3 patches do not apply any more:
* target/linux/bcm27xx/patches-5.4/950-0316-pinctrl-bcm2835-Add-support-for-BCM2711-pull-up-func.patch
This was already integrated in kernel v5.4-rc1, it was never needed.
* target/linux/bcm27xx/patches-5.4/950-0328-Revert-pinctrl-bcm2835-Pass-irqchip-when-adding-gpio.patch
* target/linux/bcm27xx/patches-5.4/950-0362-pinctrl-bcm2835-Change-init-order-for-gpio-hogs.patch
I think these were done to fix the problem which was really fixed in
commit 75278f1aff5e ("pinctrl: bcm2835: Change init order for gpio
hogs") from v5.4.175
target/linux/generic/backport-5.4/716-v5.5-net-sfp-move-fwnode-parsing-into-sfp-bus-layer.patch
Move fwnode_device_is_available to the same position as in kernel 5.10.
target/linux/layerscape/patches-5.4/302-dts-0083-arm64-ls1028a-qds-correct-bus-of-rtc.patch
Applied in commit 65816c1034769e714edb70f59a33bc5472d9e55f ("arm64: dts:
ls1028a-qds: move rtc node to the correct i2c bus")
Compile-tested: lantiq/xrx200, bcm27xx/bcm2710
Run-tested: lantiq/xrx200
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
39 lines
1.3 KiB
Diff
39 lines
1.3 KiB
Diff
From 9eeebf9e7bb7a25a81f72c0e21793614fab49ec4 Mon Sep 17 00:00:00 2001
|
|
From: Eric Anholt <eric@anholt.net>
|
|
Date: Mon, 9 May 2016 17:28:18 -0700
|
|
Subject: [PATCH] clk: bcm2835: Mark GPIO clocks enabled at boot as
|
|
critical.
|
|
|
|
These divide off of PLLD_PER and are used for the ethernet and wifi
|
|
PHYs source PLLs. Neither of them is currently represented by a phy
|
|
device that would grab the clock for us.
|
|
|
|
This keeps other drivers from killing the networking PHYs when they
|
|
disable their own clocks and trigger PLLD_PER's refcount going to 0.
|
|
|
|
v2: Skip marking as critical if they aren't on at boot.
|
|
|
|
Signed-off-by: Eric Anholt <eric@anholt.net>
|
|
---
|
|
drivers/clk/bcm/clk-bcm2835.c | 9 +++++++++
|
|
1 file changed, 9 insertions(+)
|
|
|
|
--- a/drivers/clk/bcm/clk-bcm2835.c
|
|
+++ b/drivers/clk/bcm/clk-bcm2835.c
|
|
@@ -1468,6 +1468,15 @@ static struct clk_hw *bcm2835_register_c
|
|
init.flags = data->flags | CLK_IGNORE_UNUSED;
|
|
|
|
/*
|
|
+ * Some GPIO clocks for ethernet/wifi PLLs are marked as
|
|
+ * critical (since some platforms use them), but if the
|
|
+ * firmware didn't have them turned on then they clearly
|
|
+ * aren't actually critical.
|
|
+ */
|
|
+ if ((cprman_read(cprman, data->ctl_reg) & CM_ENABLE) == 0)
|
|
+ init.flags &= ~CLK_IS_CRITICAL;
|
|
+
|
|
+ /*
|
|
* Pass the CLK_SET_RATE_PARENT flag if we are allowed to propagate
|
|
* rate changes on at least of the parents.
|
|
*/
|