mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-30 10:39:04 +00:00
9db651f4a2
The I/O base address for the timers was hardcoded into the driver, or derived from the HW IRQ number as an even more horrible hack. All supported SoC families have these timers, but with hardcoded addresses the code cannot be reused right now. Request the timer's base address from the DT specification, and store it in a private struct for future reference. Matching the second interrupt specifier, the address range for the second timer is added to the DT specification. Signed-off-by: Sander Vanheule <sander@svanheule.net>
161 lines
2.8 KiB
Plaintext
161 lines
2.8 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
/dts-v1/;
|
|
|
|
/ {
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
compatible = "realtek,rtl838x-soc";
|
|
|
|
cpus {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
frequency = <800000000>;
|
|
|
|
cpu@0 {
|
|
compatible = "mips,mips34Kc";
|
|
reg = <0>;
|
|
};
|
|
};
|
|
|
|
memory@0 {
|
|
device_type = "memory";
|
|
reg = <0x0 0x8000000>;
|
|
};
|
|
|
|
chosen {
|
|
bootargs = "console=ttyS0,115200";
|
|
};
|
|
|
|
cpuintc: cpuintc {
|
|
compatible = "mti,cpu-interrupt-controller";
|
|
#address-cells = <0>;
|
|
#interrupt-cells = <1>;
|
|
interrupt-controller;
|
|
};
|
|
|
|
lx_clk: lx_clk {
|
|
compatible = "fixed-clock";
|
|
#clock-cells = <0>;
|
|
clock-frequency = <175000000>;
|
|
};
|
|
|
|
soc: soc {
|
|
compatible = "simple-bus";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
ranges = <0x0 0x18000000 0x10000>;
|
|
|
|
intc: interrupt-controller@3000 {
|
|
compatible = "realtek,rtl9300-intc", "realtek,rtl-intc";
|
|
reg = <0x3000 0x18>, <0x3018 0x18>;
|
|
interrupt-controller;
|
|
#interrupt-cells = <2>;
|
|
|
|
interrupt-parent = <&cpuintc>;
|
|
interrupts = <2>, <3>, <4>, <5>, <6>, <7>;
|
|
};
|
|
|
|
rtl9300clock: rtl9300clock@3200 {
|
|
compatible = "realtek,rtl9300clock";
|
|
reg = <0x3200 0x10>, <0x3210 0x10>;
|
|
|
|
interrupt-parent = <&intc>;
|
|
interrupts = <7 5>, <8 5>;
|
|
};
|
|
|
|
spi0: spi@1200 {
|
|
compatible = "realtek,rtl8380-spi";
|
|
reg = <0x1200 0x100>;
|
|
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
};
|
|
|
|
uart0: uart@2000 {
|
|
compatible = "ns16550a";
|
|
reg = <0x2000 0x100>;
|
|
|
|
clocks = <&lx_clk>;
|
|
|
|
interrupt-parent = <&intc>;
|
|
interrupts = <30 1>;
|
|
|
|
reg-io-width = <1>;
|
|
reg-shift = <2>;
|
|
fifo-size = <1>;
|
|
no-loopback-test;
|
|
};
|
|
|
|
uart1: uart@2100 {
|
|
compatible = "ns16550a";
|
|
reg = <0x2100 0x100>;
|
|
|
|
clocks = <&lx_clk>;
|
|
|
|
interrupt-parent = <&intc>;
|
|
interrupts = <31 0>;
|
|
|
|
reg-io-width = <1>;
|
|
reg-shift = <2>;
|
|
fifo-size = <1>;
|
|
no-loopback-test;
|
|
|
|
status = "disabled";
|
|
};
|
|
|
|
watchdog0: watchdog@3260 {
|
|
compatible = "realtek,rtl9300-wdt";
|
|
reg = <0x3260 0xc>;
|
|
|
|
realtek,reset-mode = "soc";
|
|
|
|
clocks = <&lx_clk>;
|
|
timeout-sec = <30>;
|
|
|
|
interrupt-parent = <&intc>;
|
|
interrupt-names = "phase1", "phase2";
|
|
interrupts = <5 4>, <6 4>;
|
|
};
|
|
|
|
gpio0: gpio-controller@3300 {
|
|
compatible = "realtek,rtl9300-gpio", "realtek,otto-gpio";
|
|
reg = <0x3300 0x1c>, <0x3338 0x8>;
|
|
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
ngpios = <24>;
|
|
|
|
interrupt-controller;
|
|
#interrupt-cells = <2>;
|
|
interrupt-parent = <&intc>;
|
|
interrupts = <13 1>;
|
|
};
|
|
|
|
};
|
|
|
|
ethernet0: ethernet@1b00a300 {
|
|
compatible = "realtek,rtl838x-eth";
|
|
reg = <0x1b00a300 0x100>;
|
|
|
|
interrupt-parent = <&intc>;
|
|
interrupts = <24 3>;
|
|
|
|
phy-mode = "internal";
|
|
|
|
fixed-link {
|
|
speed = <1000>;
|
|
full-duplex;
|
|
};
|
|
};
|
|
|
|
switch0: switch@1b000000 {
|
|
compatible = "realtek,rtl83xx-switch";
|
|
status = "okay";
|
|
|
|
interrupt-parent = <&intc>;
|
|
interrupts = <23 2>;
|
|
};
|
|
};
|