openwrt/target/linux/lantiq/dts/BTHOMEHUBV5A.dts
Felix Fietkau 022855baf2 lantiq: Move the definition of the xrx200-net node to vr9.dtsi
This removes a lot of duplicate register and interrupt definitions by
moving the xrx200-net definition to vr9.dtsi and making all devices re-
use it.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

SVN-Revision: 48547
2016-01-29 00:42:45 +00:00

291 lines
5.6 KiB
Plaintext

/dts-v1/;
/include/ "vr9.dtsi"
/ {
model = "BTHOMEHUBV5A - BT Home Hub 5A";
chosen {
bootargs = "console=ttyLTQ0,115200 init=/etc/preinit";
leds {
boot = &power_green;
failsafe = &power_red;
running = &power_blue;
internet = &broadband_blue;
wifi = &wireless_blue;
};
};
memory@0 {
reg = <0x0 0x8000000>;
};
fpi@10000000 {
localbus@0 {
nand-parts@0 {
compatible = "gen_nand", "lantiq,nand-xway";
lantiq,cs = <1>;
bank-width = <2>;
reg = <0 0x0 0x2000000>;
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "u-boot";
reg = <0x0 0x40000>;
read-only;
};
partition@40000 {
label = "uboot-env";
reg = <0x40000 0x40000>;
};
caldata: partition@80000 {
label = "caldata";
reg = <0x80000 0x20000>;
read-only;
};
partition@a0000 {
label = "kernel";
reg = <0xa0000 0x200000>;
};
partition@2a0000 {
label = "ubi";
reg = <0x2a0000 0x7d60000>;
};
};
};
gpio: pinmux@E100B10 {
pinctrl-names = "default";
pinctrl-0 = <&state_default>;
interrupt-parent = <&icu0>;
interrupts = <166 135 66 40 41 42 38>;
state_default: pinmux {
mdio {
lantiq,groups = "mdio";
lantiq,function = "mdio";
};
pci_rst {
lantiq,pins = "io21";
lantiq,output = <1>;
lantiq,open-drain;
};
pcie_rst {
lantiq,pins = "io38";
lantiq,pull = <0>;
lantiq,output = <1>;
lantiq,open-drain;
};
usb_vbus {
lantiq,pins = "io33";
lantiq,pull = <0>;
lantiq,open-drain = <0>;
lantiq,output = <1>;
};
nand_out {
lantiq,groups = "nand cle", "nand ale";
lantiq,function = "ebu";
lantiq,output = <1>;
lantiq,open-drain = <0>;
lantiq,pull = <0>;
};
nand_cs1 {
lantiq,groups = "nand cs1";
lantiq,function = "ebu";
lantiq,open-drain = <0>;
lantiq,pull = <0>;
};
};
};
ifxhcd@E101000 {
status = "okay";
gpios = <&gpio 33 0>;
};
pci@E105400 {
status = "okay";
lantiq,bus-clock = <33333333>;
interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
interrupt-map = <0x7000 0 0 1 &icu0 30 1>;
gpio-reset = <&gpio 21 0>;
};
};
gphy-xrx200 {
compatible = "lantiq,phy-xrx200";
firmware1 = "lantiq/vr9_phy11g_a1x.bin"; /*VR9 1.1*/
firmware2 = "lantiq/vr9_phy11g_a2x.bin"; /*VR9 1.2*/
phys = [ 00 01 ];
};
ath9k_eep {
compatible = "ath9k,eeprom";
ath,eep-flash = <&caldata 0x1000>;
ath,mac-offset = <0x110c>;
ath,mac-increment = <2>;
ath,pci-slot = <0xe>; /* 14 */
};
gpio-keys-polled {
compatible = "gpio-keys-polled";
#address-cells = <1>;
#size-cells = <0>;
poll-interval = <100>;
reset {
label = "reset";
gpios = <&gpio 2 1>;
linux,code = <0x198>;
};
wps {
label = "wps";
gpios = <&gpio 25 1>;
linux,code = <0x211>;
};
restart {
label = "restart";
gpios = <&gpio 39 1>;
linux,code = <0x198>;
};
};
gpio-leds {
compatible = "gpio-leds";
/* broadband-* is a single RGB led */
broadband-red {
label = "bthomehubv5a:red:broadband";
gpios = <&gpio 0 1>;
};
broadband-green {
label = "bthomehubv5a:green:broadband";
gpios = <&gpio 3 1>;
};
broadband_blue: broadband-blue {
label = "bthomehubv5a:blue:broadband";
gpios = <&gpio 8 1>;
};
/* wireless-* is a single RGB led */
wireless-red {
label = "bthomehubv5a:red:wireless";
gpios = <&gpio 9 1>;
};
wireless-green {
label = "bthomehubv5a:green:wireless";
gpios = <&gpio 10 1>;
};
wireless_blue: wireless-blue {
label = "bthomehubv5a:blue:wireless";
gpios = <&gpio 11 1>;
};
/* power-* is a single RGB led */
power_red: power-red {
label = "bthomehubv5a:red:power";
gpios = <&gpio 12 1>;
};
power_green: power-green {
label = "bthomehubv5a:green:power";
gpios = <&gpio 14 1>;
default-state = "keep";
};
power_blue: power-blue {
label = "bthomehubv5a:blue:power";
gpios = <&gpio 15 1>;
};
dimmed {
label = "dimmed";
gpios = <&gpio 19 0>;
};
};
};
&eth0 {
lan: interface@0 {
compatible = "lantiq,xrx200-pdi";
#address-cells = <1>;
#size-cells = <0>;
reg = <0>;
mtd-mac-address = <&caldata 0x110c>;
lantiq,switch;
ethernet@0 {
compatible = "lantiq,xrx200-pdi-port";
reg = <0>;
phy-mode = "rgmii";
phy-handle = <&phy0>;
};
ethernet@1 {
compatible = "lantiq,xrx200-pdi-port";
reg = <1>;
phy-mode = "rgmii";
phy-handle = <&phy1>;
};
ethernet@2 {
compatible = "lantiq,xrx200-pdi-port";
reg = <2>;
phy-mode = "gmii";
phy-handle = <&phy11>;
};
ethernet@4 {
compatible = "lantiq,xrx200-pdi-port";
reg = <4>;
phy-mode = "gmii";
phy-handle = <&phy13>;
};
};
wan: interface@1 {
compatible = "lantiq,xrx200-pdi";
#address-cells = <1>;
#size-cells = <0>;
reg = <1>;
mtd-mac-address = <&caldata 0x110c>;
mtd-mac-address-increment = <4>;
lantiq,wan;
ethernet@5 {
compatible = "lantiq,xrx200-pdi-port";
reg = <5>;
phy-mode = "rgmii";
phy-handle = <&phy5>;
};
};
mdio@0 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "lantiq,xrx200-mdio";
phy0: ethernet-phy@0 {
reg = <0x0>;
compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
};
phy1: ethernet-phy@1 {
reg = <0x1>;
compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
};
phy5: ethernet-phy@5 {
reg = <0x5>;
compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
};
phy11: ethernet-phy@11 {
reg = <0x11>;
compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
};
phy13: ethernet-phy@13 {
reg = <0x13>;
compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
};
};
};