mirror of
https://github.com/openwrt/openwrt.git
synced 2025-01-08 22:12:49 +00:00
bc18c2bfe7
This board was used in dual-band 802.11n enterprise access points, models BSAP-1800v2 and BSAP-1840, introduced in 2010 by Bluesocket, which was acquired by Adtran in 2011, who has now EOL'ed them. They differed only in that the BSAP-1840's antennae were detachable, while the BSAP-1800v2's were inside the case. They have an external RJ-45 console port, which works with standard Cisco 72-3383-01 console cables. Specification: - System-On-Chip: AR7161 - CPU/Speed: 600 MHz - Flash-Chip: Macronix MX25L12845E - Flash size: 16 MiB - RAM: 64 MiB - Wireless No1: Lite-On WN2601A card: AR9160/AR9103 2.4GHz 802.11bgn - Wireless No2: Lite-On WN2502A card: AR9160/AR9106 5GHz 802.11an - PHY: Vitesse VSC8601, Rev. B Installation: 1. Connect to the serial console using a terminal that supports YMODEM at 115200 bps, 8 data bits, no parity, 1 stop bit 2. Interrupt the bootloader using its password, which is: r00t 3. Issue the "fis init" command, confirming if prompted 4. Look at the length of the openwrt-ath79-generic-*-squashfs-kernel.bin file, and substitute it below, instead of where I have "LeNgTh" 5. Issue the following command, and upload this file using YMODEM protocol load -r -v -b 0x80060000 -m ymodem 6. Issue the following commands, substituting as mentioned above: fis create -b 0x80060000 -l LeNgTh vmlinux_2 load -r -v -b 0x80100000 -m ymodem 7. Using YMODEM, upload openwrt-ath79-generic-*-squashfs-rootfs.bin 8. Issue the "fis free" command, and for the first range in its response, use a hexadecimal calculator to subtract the start from the end in order to substitute it below, with the leading "0x" to specify it in hexadecimal, instead of where I have "LeNgTh" 9. Issue the following commands, substituting as mentioned above: fis create -b 0x80100000 -l LeNgTh -e 0 -r 0 rootfs reset 10.Wait for the status LED to go solid green Tested-by: Brian Gonyer <bgonyer@gmail.com> Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us> [fixed obsolete $ARGV in platform_do_upgrade] Signed-off-by: Petr Štetiar <ynezz@true.cz>
59 lines
1.3 KiB
Bash
59 lines
1.3 KiB
Bash
#
|
|
# Copyright (C) 2011 OpenWrt.org
|
|
#
|
|
|
|
PART_NAME=firmware
|
|
REQUIRE_IMAGE_METADATA=1
|
|
|
|
redboot_fis_do_upgrade() {
|
|
local append
|
|
local sysup_file="$1"
|
|
local kern_part="$2"
|
|
local magic=$(get_magic_word "$sysup_file")
|
|
|
|
if [ "$magic" = "4349" ]; then
|
|
local kern_length=0x$(dd if="$sysup_file" bs=2 skip=1 count=4 2>/dev/null)
|
|
|
|
[ -f "$CONF_TAR" -a "$SAVE_CONFIG" -eq 1 ] && append="-j $CONF_TAR"
|
|
dd if="$sysup_file" bs=64k skip=1 2>/dev/null | \
|
|
mtd -r $append -F$kern_part:$kern_length:0x80060000,rootfs write - $kern_part:rootfs
|
|
|
|
elif [ "$magic" = "7379" ]; then
|
|
local board_dir=$(tar tf $sysup_file | grep -m 1 '^sysupgrade-.*/$')
|
|
local kern_length=$(tar xf $sysup_file ${board_dir}kernel -O | wc -c)
|
|
|
|
[ -f "$CONF_TAR" -a "$SAVE_CONFIG" -eq 1 ] && append="-j $CONF_TAR"
|
|
tar xf $sysup_file ${board_dir}kernel ${board_dir}root -O | \
|
|
mtd -r $append -F$kern_part:$kern_length:0x80060000,rootfs write - $kern_part:rootfs
|
|
|
|
else
|
|
echo "Unknown image, aborting!"
|
|
return 1
|
|
fi
|
|
}
|
|
|
|
platform_check_image() {
|
|
return 0
|
|
}
|
|
|
|
platform_do_upgrade() {
|
|
local board=$(board_name)
|
|
|
|
case "$board" in
|
|
adtran,bsap1800-v2|\
|
|
adtran,bsap1840)
|
|
redboot_fis_do_upgrade "$1" vmlinux_2
|
|
;;
|
|
jjplus,ja76pf2)
|
|
redboot_fis_do_upgrade "$1" linux
|
|
;;
|
|
ubnt,routerstation|\
|
|
ubnt,routerstation-pro)
|
|
redboot_fis_do_upgrade "$1" kernel
|
|
;;
|
|
*)
|
|
default_do_upgrade "$1"
|
|
;;
|
|
esac
|
|
}
|