openwrt/target/linux/ipq806x/files/arch/arm/boot/dts
Yanase Yuki 3bb1618573 ipq806x: add support for NEC Platforms Aterm WG2600HP3
NEC Platforms Aterm WG2600HP3 is a dual-band router based on Qualcomm IPQ8062.

Specification
-------------
- SoC: Qualcomm IPQ8062
- RAM: 512MiB
- Flash memory: SPI-NOR 32MiB (Cypress S25FL256S)
- Wi-Fi: Qualcomm QCA9984 (2.4GHz, 1ch - 13ch)
- Wi-Fi: Qualcomm QCA9984 (5GHz, 36ch - 64ch, 100ch - 140ch)
- Ethernet: 4x 100/1000 Mbps (1x WAN, 4x LAN)
- LED: 6x green LED, 6x red LED
- Input: 2x tactile switch, 1x SP3T slide switch
- Serial console: 115200bps, through-hole J3
  - [  ] [GND] [  ] [TX] [RX] ----> DC jack
- Power: DC 12V 1.5A

This device does not support VHT160 and VHT80+80.
Custom BDFs are required to limit VHT capabilities.

Flash instructions
------------------
1. Setup TFTP server (IP address: 192.168.1.2)
2. Put initramfs image into TFTP server directory
3. Connect WG2600HP3 lan port and computer that runs TFTP server
4. Connect to the serial console
5. Interrupt booting by Esc key (password: chiron)
6. Execute the following commands
    # setenv bootcmd "nboot 0x44000000 1 0x860000"
    # saveenv
    # setenv ipaddr 192.168.1.1
    # setenv serverip 192.168.1.2
    # tftpboot 0x44000000 openwrt-ipq806x-generic-nec_wg2600hp3-initramfs-uImage
7. After booting OpenWrt initramfs image, backup SPI-NOR flash memory
8. Erase firmware partition
    # mtd erase firmware
9. Run sysupgrade

Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
2020-12-25 10:38:13 +01:00
..
qcom-ipq8062-wg2600hp3.dts ipq806x: add support for NEC Platforms Aterm WG2600HP3 2020-12-25 10:38:13 +01:00
qcom-ipq8062.dtsi ipq806x: add support for Qualcomm IPQ8062 SoC 2020-12-25 10:38:13 +01:00
qcom-ipq8064-ap148.dts ipq806x: remove support for kernel 4.19 2020-10-19 15:37:54 +02:00
qcom-ipq8064-ap161.dts ipq806x: remove support for kernel 4.19 2020-10-19 15:37:54 +02:00
qcom-ipq8064-c2600.dts ipq806x: remove support for kernel 4.19 2020-10-19 15:37:54 +02:00
qcom-ipq8064-d7800.dts ipq806x: Fix gmac1 (WAN) on Netgear D7800 2020-12-22 18:59:10 +01:00
qcom-ipq8064-db149.dts ipq806x: remove support for kernel 4.19 2020-10-19 15:37:54 +02:00
qcom-ipq8064-ea7500-v1.dts ipq806x: remove support for kernel 4.19 2020-10-19 15:37:54 +02:00
qcom-ipq8064-ea8500.dts ipq806x: remove support for kernel 4.19 2020-10-19 15:37:54 +02:00
qcom-ipq8064-eax500.dtsi ipq806x: remove support for kernel 4.19 2020-10-19 15:37:54 +02:00
qcom-ipq8064-r7500.dts ipq806x: remove support for kernel 4.19 2020-10-19 15:37:54 +02:00
qcom-ipq8064-r7500v2.dts ipq806x: remove support for kernel 4.19 2020-10-19 15:37:54 +02:00
qcom-ipq8064-v2.0.dtsi ipq806x: remove support for kernel 4.19 2020-10-19 15:37:54 +02:00
qcom-ipq8064-vr2600v.dts ipq806x: remove support for kernel 4.19 2020-10-19 15:37:54 +02:00
qcom-ipq8064-wg2600hp.dts ipq806x: disable SPC of IPQ8064 on NEC WG2600HP to fix boot issue 2020-12-22 19:11:50 +01:00
qcom-ipq8064-wpq864.dts ipq806x: remove support for kernel 4.19 2020-10-19 15:37:54 +02:00
qcom-ipq8064-wxr-2533dhp.dts ipq806x: remove support for kernel 4.19 2020-10-19 15:37:54 +02:00
qcom-ipq8065-nbg6817.dts ipq806x: remove support for kernel 4.19 2020-10-19 15:37:54 +02:00
qcom-ipq8065-r7800.dts ipq806x: remove support for kernel 4.19 2020-10-19 15:37:54 +02:00
qcom-ipq8065.dtsi ipq806x: remove support for kernel 4.19 2020-10-19 15:37:54 +02:00
qcom-ipq8068-ecw5410.dts ipq806x: remove support for kernel 4.19 2020-10-19 15:37:54 +02:00