openwrt/target/linux/bcm63xx/patches-5.4/513-board-bcm6338.patch
Daniele Castro c143fbc5f1 bcm63xx: add support for Technicolor TG582n Telecom Italia branded
Technicolor TG582n Telecom Italia branded a.k.a.
Telecom Italia ADSL2+ Wi-Fi N (AGTWI)
has the same PCB as the unbranded Technicolor TG582n with LEDs
connected to different GPIO PINs in active low configuration and
different LED names. It has a PCB similar to the OpenWrt's ADB P.DG A4001N1 one.

Hardware:
* Board ID: DANT-V
* SoC: Broadcom BCM6328 (rev b0) @ 320MHz, CPU BMIPS4350
* RAM DDR2: 64 Mbyte - EtronTech EM68B16CWQD-25H
* Serial flash: 16 Mbyte - Spansion FL 128SAIF00
* Ethernet: 4x Ethernet 10/100 baseT
* Wifi 2.4GHz: Broadcom Corporation BCM43227 Wireless Network Adapter (rev 30)
* LEDs: 2x Power, 1x ADSL, 2x Internet, 2x Wi-Fi, 2x Service, 4x ethernet
* Buttons: 1x Reset, 1x WPS (named WiFi/LED)
* UART: 1x TTL 115200n8, VCC GND TX RX, on J3 connector (short R62 and R63)

Installation via CFE:
* Stock CFE has to be overwritten with a generic 6328 one that can upload
  .bin images with no signature check (cfe6328_configured.bin)
* Connect a serial port to the board
* Stop the CFE boot process after power on by pressing enter
* Set static IP 192.168.2.10 and subnet mask 255.255.255.0
* Navigate to http://192.168.2.50/
* Upload the OpenWrt image file

PCB:   |GPIO:   |TG582n:          |AGTWI:

LED2R  |488(08) |red    Power     |red   Power
LED2G  |484(04) |green  Power     |green Power

LED10R |486(06) |                 |missing R85 end LED
LED13G |485(05) |green  Ethernet  |green ADSL

LED11R |494(14) |                 |red   Internet
LED14G |491(11) |green  Broadband |green Internet

LED5R  |487(07) |red    Internet  |red   Wi-Fi
LED5G  |481(01) |green  Internet  |green Wi-Fi

LED12R |498(18) |                 |red   Service
LED12G |499(19) |                 |green Service

LED6R  |482(02) |red    Wi-Fi     |missing R108 end LED
LED6G  |483(03) |green  Wi-Fi     |missing R107 end LED

LED7R  |490(10) |red    WPS       |missing R91 end LED
LED7G  |489(09) |green  WPS       |missing R92 end LED

LED4   |508(28) |ethernet port 4  |ethernet port 4
LED3   |507(27) |ethernet port 3  |ethernet port 3

LED9   |506(26) |ethernet port 2  |ethernet port 2
LED8   |505(25) |ethernet port 1  |ethernet port 1

SW3    |503(23) |key Reset        |key Reset

SW5    |504(24) |key WPS          |key Wi-Fi/LED

SW4    |495(15) |key Wi-Fi        |missing R127 end key

SW6    |493(13) |                 |missing R171 end key

SW1    |492(12) |                 |missing R1 end key

Signed-off-by: Daniele Castro <danielecastro@hotmail.it>
[DT fixes, base-files fixes and device variant]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-12-06 19:17:41 +01:00

54 lines
1.4 KiB
Diff

--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
@@ -943,6 +943,32 @@ static struct board_info __initdata boar
.force_duplex_full = 1,
},
};
+
+static struct board_info __initdata board_96338w2_e7t = {
+ .name = "96338W2_E7T",
+ .expected_cpu_id = 0x6338,
+
+ .has_enet0 = 1,
+ .enet0 = {
+ .has_phy = 1,
+ .phy_id = 0,
+ .force_speed_100 = 1,
+ .force_duplex_full = 1,
+ },
+};
+
+static struct board_info __initdata board_rta1320_16m = {
+ .name = "RTA1320_16M",
+ .expected_cpu_id = 0x6338,
+
+ .has_enet0 = 1,
+ .enet0 = {
+ .has_phy = 1,
+ .phy_id = 0,
+ .force_speed_100 = 1,
+ .force_duplex_full = 1,
+ },
+};
#endif /* CONFIG_BCM63XX_CPU_6338 */
/*
@@ -1281,6 +1307,8 @@ static const struct board_info __initcon
#ifdef CONFIG_BCM63XX_CPU_6338
&board_96338gw,
&board_96338w,
+ &board_96338w2_e7t,
+ &board_rta1320_16m,
#endif /* CONFIG_BCM63XX_CPU_6338 */
#ifdef CONFIG_BCM63XX_CPU_6345
&board_96345gw2,
@@ -1335,6 +1363,8 @@ static struct of_device_id const bcm963x
#ifdef CONFIG_BCM63XX_CPU_6338
{ .compatible = "brcm,bcm96338gw", .data = &board_96338gw, },
{ .compatible = "brcm,bcm96338w", .data = &board_96338w, },
+ { .compatible = "d-link,dsl-2640u", .data = &board_96338w2_e7t, },
+ { .compatible = "dynalink,rta1320", .data = &board_rta1320_16m, },
#endif /* CONFIG_BCM63XX_CPU_6338 */
#ifdef CONFIG_BCM63XX_CPU_6345
{ .compatible = "brcm,bcm96345gw2", .data = &board_96345gw2, },