c13263ca07
Add support for D-Link DIR-1935 A1 based on similarities to DIR-882 A1, DIR-867 A1 and other DIR-8xx A1 models. Existing DIR-882 A1 openwrt "factory" firmware installs without modificaitons via the D-Link Recovery GUI and has no known incompatibilities with the DIR-1935 A1. Changes to be committed: new file: target/linux/ramips/dts/mt7621_dlink_dir-1935-a1.dts modified: target/linux/ramips/image/mt7621.mk modified: target/linux/ramips/mt7621/base-files/etc/board.d/01_leds Specifications: * Board: Not known * SoC: MediaTek MT7621 Family * RAM: 128 MB (DDR3) * Flash: 16 MB (SPI NOR) * WiFi: MediaTek MT7615 Family (x2) * Switch: 1 WAN, 4 LAN (Gigabit) * Ports: 1 USB 3.0 * Buttons: Reset, WiFi Toggle, WPS * LEDs: Power (green/orange), Internet (green/orange), WiFi 2.4G (green), WiFi 5G (green) Notes: * 160MHz 5GHz is available in LuCi but does not appear to work (i.e. no SSID is visible in wifi scanning apps on other devices) with either official DIR-882 A1 firmware or a test build for the DIR-1935 A1 based on the 22.03.2 branch. 80 MHz 5GHz works. Serial port: * Untested (potential user damage/error) * Expected to be identical to other DIR-8xx A1 models: * Parameters: 57600, 8N1 * Location: J1 header (close to the Reset, WiFi and WPS buttons) * Pinout: 1 - VCC 2 - RXD 3 - TXD 4 - GND Installation: * D-Link Recovery GUI: power down the router, press and hold the reset button, then re-plug it. Keep the reset button pressed until the power LED starts flashing orange, manually assign a static IP address under the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1 * Some modern browsers may have problems flashing via the Recovery GUI, if that occurs consider uploading the firmware through cURL: curl -v -i -F "firmware=@file.bin" 192.168.0.1 Signed-off-by: Keith Harrison <keithh@protonmail.com> |
||
---|---|---|
.github | ||
config | ||
include | ||
LICENSES | ||
package | ||
scripts | ||
target | ||
toolchain | ||
tools | ||
.gitattributes | ||
.gitignore | ||
BSDmakefile | ||
Config.in | ||
COPYING | ||
feeds.conf.default | ||
Makefile | ||
README.md | ||
rules.mk |
OpenWrt Project is a Linux operating system targeting embedded devices. Instead of trying to create a single, static firmware, OpenWrt provides a fully writable filesystem with package management. This frees you from the application selection and configuration provided by the vendor and allows you to customize the device through the use of packages to suit any application. For developers, OpenWrt is the framework to build an application without having to build a complete firmware around it; for users this means the ability for full customization, to use the device in ways never envisioned.
Sunshine!
Download
Built firmware images are available for many architectures and come with a package selection to be used as WiFi home router. To quickly find a factory image usable to migrate from a vendor stock firmware to OpenWrt, try the Firmware Selector.
If your device is supported, please follow the Info link to see install instructions or consult the support resources listed below.
An advanced user may require additional or specific package. (Toolchain, SDK, ...) For everything else than simple firmware download, try the wiki download page:
Development
To build your own firmware you need a GNU/Linux, BSD or MacOSX system (case sensitive filesystem required). Cygwin is unsupported because of the lack of a case sensitive file system.
Requirements
You need the following tools to compile OpenWrt, the package names vary between distributions. A complete list with distribution specific packages is found in the Build System Setup documentation.
binutils bzip2 diff find flex gawk gcc-6+ getopt grep install libc-dev libz-dev
make4.1+ perl python3.6+ rsync subversion unzip which
Quickstart
-
Run
./scripts/feeds update -a
to obtain all the latest package definitions defined in feeds.conf / feeds.conf.default -
Run
./scripts/feeds install -a
to install symlinks for all obtained packages into package/feeds/ -
Run
make menuconfig
to select your preferred configuration for the toolchain, target system & firmware packages. -
Run
make
to build your firmware. This will download all sources, build the cross-compile toolchain and then cross-compile the GNU/Linux kernel & all chosen applications for your target system.
Related Repositories
The main repository uses multiple sub-repositories to manage packages of
different categories. All packages are installed via the OpenWrt package
manager called opkg
. If you're looking to develop the web interface or port
packages to OpenWrt, please find the fitting repository below.
-
LuCI Web Interface: Modern and modular interface to control the device via a web browser.
-
OpenWrt Packages: Community repository of ported packages.
-
OpenWrt Routing: Packages specifically focused on (mesh) routing.
-
OpenWrt Video: Packages specifically focused on display servers and clients (Xorg and Wayland).
Support Information
For a list of supported devices see the OpenWrt Hardware Database
Documentation
Support Community
- Forum: For usage, projects, discussions and hardware advise.
- Support Chat: Channel
#openwrt
on oftc.net.
Developer Community
- Bug Reports: Report bugs in OpenWrt
- Dev Mailing List: Send patches
- Dev Chat: Channel
#openwrt-devel
on oftc.net.
License
OpenWrt is licensed under GPL-2.0