mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-23 15:32:33 +00:00
c27279dc26
Hardware: SoC: MediaTek MT7629 Cortex-A7 (ARMv7 1.25GHz, Dual-Core) RAM: DDR3 128MB Flash: Macronix MX35LF1GE4AB (SPI-NAND 128MB) WiFi: MediaTek MT7761N (2.4GHz) / MediaTek MT7762N (5GHz) - no driver Ethernet: SoC (WAN) / MediaTek MT7531 (LAN x4) UART: [GND, RX, TX, 3.3V] (115200) Installation: - Flash recovery image with TFTP recovery Revert to stock firmware: - Flash stock firmware with TFTP recovery TFTP Recovery method: 1. Unplug the router 2. Hold the reset button and plug in 3. Release when the power LED stops flashing and go off 4. Set your computer IP address manually to 192.168.0.x / 255.255.255.0 5. Flash image with TFTP client to 192.168.0.1 Signed-off-by: Yoonji Park <koreapyj@dcmys.kr>
295 lines
4.8 KiB
Plaintext
295 lines
4.8 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0
|
|
|
|
/dts-v1/;
|
|
#include <dt-bindings/input/input.h>
|
|
#include "mt7629.dtsi"
|
|
|
|
/ {
|
|
model = "ipTIME A6004MX";
|
|
compatible = "iptime,a6004mx", "mediatek,mt7629";
|
|
|
|
aliases {
|
|
led-boot = &led_cpu;
|
|
led-failsafe = &led_cpu;
|
|
led-running = &led_cpu;
|
|
led-upgrade = &led_cpu;
|
|
serial0 = &uart0;
|
|
};
|
|
|
|
chosen {
|
|
stdout-path = "serial0:115200n8";
|
|
bootargs-override = "console=ttyS0,115200n8";
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
led_cpu: cpu {
|
|
label = "orange:cpu";
|
|
gpios = <&pio 57 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
wlan5g {
|
|
label = "orange:wlan5g";
|
|
gpios = <&pio 22 GPIO_ACTIVE_LOW>;
|
|
// linux,default-trigger = "phy0radio";
|
|
};
|
|
|
|
wlan2g {
|
|
label = "orange:wlan2g";
|
|
gpios = <&pio 21 GPIO_ACTIVE_LOW>;
|
|
// linux,default-trigger = "phy1radio";
|
|
};
|
|
|
|
wan {
|
|
label = "orange:wan";
|
|
gpios = <&pio 12 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
reset {
|
|
label = "factory";
|
|
linux,code = <KEY_RESTART>;
|
|
gpios = <&pio 60 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
wps {
|
|
label = "wps";
|
|
linux,code = <KEY_WPS_BUTTON>;
|
|
gpios = <&pio 58 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
memory@40000000 {
|
|
device_type = "memory";
|
|
reg = <0x40000000 0x10000000>;
|
|
};
|
|
|
|
reg_3p3v: regulator-3p3v {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "fixed-3.3V";
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
regulator-boot-on;
|
|
regulator-always-on;
|
|
};
|
|
|
|
reg_5v: regulator-5v {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "fixed-5V";
|
|
regulator-min-microvolt = <5000000>;
|
|
regulator-max-microvolt = <5000000>;
|
|
regulator-boot-on;
|
|
regulator-always-on;
|
|
};
|
|
};
|
|
|
|
ð {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <ð_pins>;
|
|
pinctrl-1 = <&ephy_leds_pins>;
|
|
status = "okay";
|
|
|
|
gmac0: mac@0 {
|
|
compatible = "mediatek,eth-mac";
|
|
reg = <0>;
|
|
phy-mode = "2500base-x";
|
|
nvmem-cells = <&macaddr_factory_4>;
|
|
nvmem-cell-names = "mac-address";
|
|
mac-address-increment = <3>;
|
|
|
|
fixed-link {
|
|
speed = <2500>;
|
|
full-duplex;
|
|
pause;
|
|
};
|
|
};
|
|
|
|
gmac1: mac@1 {
|
|
compatible = "mediatek,eth-mac";
|
|
reg = <1>;
|
|
phy-mode = "gmii";
|
|
phy-handle = <&phy0>;
|
|
nvmem-cells = <&macaddr_factory_4>;
|
|
nvmem-cell-names = "mac-address";
|
|
mac-address-increment = <1>;
|
|
};
|
|
|
|
mdio: mdio-bus {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
phy0: ethernet-phy@0 {
|
|
reg = <0>;
|
|
};
|
|
|
|
switch@2 {
|
|
compatible = "mediatek,mt7531";
|
|
reg = <2>;
|
|
reset-gpios = <&pio 28 0>;
|
|
interrupt-controller;
|
|
#interrupt-cells = <1>;
|
|
interrupt-parent = <&pio>;
|
|
interrupts = <6 IRQ_TYPE_LEVEL_HIGH>;
|
|
|
|
ports {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
port@0 {
|
|
reg = <0>;
|
|
label = "lan1";
|
|
};
|
|
|
|
port@1 {
|
|
reg = <1>;
|
|
label = "lan2";
|
|
};
|
|
|
|
port@2 {
|
|
reg = <2>;
|
|
label = "lan3";
|
|
};
|
|
|
|
port@3 {
|
|
reg = <3>;
|
|
label = "lan4";
|
|
};
|
|
|
|
port@6 {
|
|
reg = <6>;
|
|
label = "cpu";
|
|
ethernet = <&gmac0>;
|
|
phy-mode = "2500base-x";
|
|
|
|
fixed-link {
|
|
speed = <2500>;
|
|
full-duplex;
|
|
pause;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&bch {
|
|
status = "okay";
|
|
};
|
|
|
|
&snfi {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&serial_nand_pins>;
|
|
status = "okay";
|
|
flash@0 {
|
|
compatible = "spi-nand";
|
|
reg = <0>;
|
|
spi-tx-bus-width = <4>;
|
|
spi-rx-bus-width = <4>;
|
|
nand-ecc-engine = <&snfi>;
|
|
mediatek,bmt-v2;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "Bootloader";
|
|
reg = <0x0 0x100000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@100000 {
|
|
label = "Config";
|
|
reg = <0x100000 0x40000>;
|
|
};
|
|
|
|
partition@140000 {
|
|
label = "factory";
|
|
reg = <0x140000 0x80000>;
|
|
read-only;
|
|
|
|
compatible = "nvmem-cells";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
macaddr_factory_4: macaddr@4 {
|
|
reg = <0x4 0x6>;
|
|
};
|
|
};
|
|
|
|
partition@1c0000 {
|
|
label = "firmware";
|
|
reg = <0x1c0000 0x7400000>;
|
|
compatible = "denx,fit";
|
|
openwrt,fit-offset = <0x800>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&pio {
|
|
eth_pins: eth-pins {
|
|
mux {
|
|
function = "eth";
|
|
groups = "mdc_mdio";
|
|
};
|
|
};
|
|
|
|
ephy_leds_pins: ephy-leds-pins {
|
|
mux {
|
|
function = "led";
|
|
groups = "ephy_leds";
|
|
};
|
|
};
|
|
|
|
/* Serial NAND is shared pin with SPI-NOR */
|
|
serial_nand_pins: serial-nand-pins {
|
|
mux {
|
|
function = "flash";
|
|
groups = "snfi";
|
|
};
|
|
};
|
|
|
|
uart0_pins: uart0-pins {
|
|
mux {
|
|
function = "uart";
|
|
groups = "uart0_txd_rxd" ;
|
|
};
|
|
};
|
|
|
|
watchdog_pins: watchdog-pins {
|
|
mux {
|
|
function = "watchdog";
|
|
groups = "watchdog";
|
|
};
|
|
};
|
|
};
|
|
|
|
&ssusb {
|
|
vusb33-supply = <®_3p3v>;
|
|
vbus-supply = <®_5v>;
|
|
status = "okay";
|
|
};
|
|
|
|
&uart0 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&uart0_pins>;
|
|
status = "okay";
|
|
};
|
|
|
|
&watchdog {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&watchdog_pins>;
|
|
status = "okay";
|
|
|
|
interrupt-controller;
|
|
#interrupt-cells = <1>;
|
|
interrupt-parent = <&pio>;
|
|
interrupts = <GIC_SPI 0x80 IRQ_TYPE_EDGE_FALLING>;
|
|
};
|