openwrt/target/linux/rtl838x/patches-5.4/700-net-dsa-add-support-for-rtl838x-switch.patch
Birger Koblitz df8e6be59a rtl838x: add new architecture
This adds support for the RTL838x Architecture.
SoCs of this type are used in managed and un-managed Switches and Routers
with 8-28 ports. Drivers are provided for SoC initialization, GPIOs, Flash,
Ethernet including a DSA switch driver and internal and external PHYs used
with these switches.

Supported SoCs:

	RTL8380M
	RTL8381M
	RTL8382M

The kernel will also boot on the following RTL839x SoCs, however driver
support apart from spi-nor is missing:

	RTL8390
	RTL8391
	RTL8393

The following PHYs are supported:

	RTL8214FC (Quad QSGMII multiplexing GMAC and SFP port)
	RTL8218B internal: internal PHY of the RTL838x chips
	RTL8318b external (QSGMII 8-port GMAC phy)
	RTL8382M SerDes for 2 SFP ports
	Initialization sequences for the PHYs are provided in the form of
	firmware files.

Flash driver supports 3 / 4 byte access

DSA switch driver supports VLANs, port isolation, STP and port mirroring.

The ALLNET ALL-SG8208M is supported as Proof of Concept:

	RTL8382M SoC
	1 MIPS 4KEc core @ 500MHz
	8 Internal PHYs (RTL8218B)
	128MB DRAM (Nanya NT5TU128MB)
	16MB NOR Flash (MXIC 25L128)
	8 GBEthernet ports with one green status LED each (SoC controlled)
	1 Power LED (not configurable)
	1 SYS LED (configurable)
	1 On-Off switch (not configurable)
	1 Reset button at the right behind right air-vent (not configurable)
	1 Reset button on front panel (configurable)
	12V 1A barrel connector
	1 serial header with populated standard pin connector and with markings
	  GND TX RX Vcc(3.3V), connection properties: 115200 8N1

To install, upload the sysupgrade image to the OEM webpage.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2020-09-14 07:54:30 +02:00

27 lines
974 B
Diff

--- a/drivers/net/dsa/Kconfig
+++ b/drivers/net/dsa/Kconfig
@@ -74,6 +74,13 @@ config NET_DSA_REALTEK_SMI
This enables support for the Realtek SMI-based switch
chips, currently only RTL8366RB.
+config NET_DSA_RTL838X
+ tristate "Realtek rtl838x switch support"
+ depends on RTL838X
+ select NET_DSA_TAG_TRAILER
+ ---help---
+ Say Y here if you want to use the Realtek rtl838x switch.
+
config NET_DSA_SMSC_LAN9303
tristate
select NET_DSA_TAG_LAN9303
--- a/drivers/net/dsa/Makefile
+++ b/drivers/net/dsa/Makefile
@@ -11,6 +11,7 @@ obj-$(CONFIG_NET_DSA_MV88E6060) += mv88e
obj-$(CONFIG_NET_DSA_QCA8K) += qca8k.o
obj-$(CONFIG_NET_DSA_REALTEK_SMI) += realtek-smi.o
realtek-smi-objs := realtek-smi-core.o rtl8366.o rtl8366rb.o
+obj-$(CONFIG_NET_DSA_RTL838X) += rtl838x_sw.o rtl838x_phy.o
obj-$(CONFIG_NET_DSA_SMSC_LAN9303) += lan9303-core.o
obj-$(CONFIG_NET_DSA_SMSC_LAN9303_I2C) += lan9303_i2c.o
obj-$(CONFIG_NET_DSA_SMSC_LAN9303_MDIO) += lan9303_mdio.o