mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-27 09:12:39 +00:00
8eeb57acb7
This adds support for the D-Link DSL-2750u rev C1. (https://deviwiki.com/wiki/D-Link_DSL-2750U_rev_C1) It uses the same hardware as ADB P.DG A4001N. CPU: Broadcom BCM63281 (320 MHz) RAM: 32M (Winbond W9725G6JB) Flash: 8M (MXIC MX25L6445E) Ethernet: 4x 100 Mbps Wireless: 802.11b/g/n: BCM43225 USB: 1x 2.0 Flash instructions: 1. Assign static IP 192.168.1.100 to PC 2. Unplug the power source 3. Press the RESET button at the router, don't release it yet! 4. Plug the power source.Wait some seconds 5. Release the RESET button 6. Browse to http://192.168.1.1 7. Send the openwrt-bcm63xx-generic-DSL2750U-C1-squashfs-cfe.bin and wait some minutes until the firmware upgrade finish. Signed-off-by: Ahmed Naseef <naseefkm@gmail.com> [DTS improvements, proper board patch, refresh patches] Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
147 lines
2.2 KiB
Plaintext
147 lines
2.2 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
#include "bcm6328.dtsi"
|
|
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
model = "D-Link DSL-2750U rev C1";
|
|
compatible = "d-link,dsl-2750u-c1", "brcm,bcm6328";
|
|
|
|
aliases {
|
|
led-boot = &led_power_green;
|
|
led-failsafe = &led_power_green;
|
|
led-running = &led_power_green;
|
|
led-upgrade = &led_power_green;
|
|
};
|
|
|
|
chosen {
|
|
bootargs = "rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200";
|
|
stdout-path = "serial0:115200n8";
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys-polled";
|
|
poll-interval = <20>;
|
|
|
|
wifi {
|
|
label = "wifi";
|
|
gpios = <&pinctrl 12 1>;
|
|
linux,code = <KEY_WLAN>;
|
|
debounce-interval = <60>;
|
|
};
|
|
|
|
reset {
|
|
label = "reset";
|
|
gpios = <&pinctrl 23 1>;
|
|
linux,code = <KEY_RESTART>;
|
|
debounce-interval = <60>;
|
|
};
|
|
|
|
wps {
|
|
label = "wps";
|
|
gpios = <&pinctrl 24 1>;
|
|
linux,code = <KEY_WPS_BUTTON>;
|
|
debounce-interval = <60>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&hsspi {
|
|
status = "okay";
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
spi-max-frequency = <16666667>;
|
|
spi-tx-bus-width = <2>;
|
|
spi-rx-bus-width = <2>;
|
|
reg = <0>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
cfe@0 {
|
|
reg = <0x000000 0x010000>;
|
|
label = "cfe";
|
|
read-only;
|
|
};
|
|
|
|
linux@10000 {
|
|
reg = <0x010000 0x7e0000>;
|
|
label = "linux";
|
|
compatible = "brcm,bcm963xx-imagetag";
|
|
};
|
|
|
|
nvram@7f0000 {
|
|
reg = <0x7f0000 0x010000>;
|
|
label = "nvram";
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&leds {
|
|
status = "okay";
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_leds>;
|
|
|
|
led@1 {
|
|
reg = <1>;
|
|
active-low;
|
|
label = "green:inet";
|
|
};
|
|
|
|
led_power_green: led@4 {
|
|
reg = <4>;
|
|
active-low;
|
|
label = "green:power";
|
|
default-state = "on";
|
|
};
|
|
|
|
led@7 {
|
|
reg = <7>;
|
|
active-low;
|
|
label = "red:inet";
|
|
};
|
|
|
|
led@8 {
|
|
reg = <8>;
|
|
active-low;
|
|
label = "red:power";
|
|
};
|
|
|
|
led@9 {
|
|
reg = <9>;
|
|
active-low;
|
|
label = "green:wps";
|
|
};
|
|
|
|
led@10 {
|
|
reg = <10>;
|
|
active-low;
|
|
label = "green:usb";
|
|
};
|
|
|
|
led@11 {
|
|
reg = <11>;
|
|
active-low;
|
|
label = "green:dsl";
|
|
};
|
|
};
|
|
|
|
&pinctrl {
|
|
pinctrl_leds: leds {
|
|
function = "led";
|
|
pins = "gpio1", "gpio4", "gpio7",
|
|
"gpio8", "gpio9", "gpio10",
|
|
"gpio11";
|
|
};
|
|
};
|
|
|
|
&uart0 {
|
|
status = "okay";
|
|
};
|