openwrt/package/firmware
Dirk Buchwalder 26c095cb4d ipq807x: add Dynalink DL-WRX36
Dynalink DL-WRX36 is a AX WIFI router with 4 1G and 1 2.5G ports.

Specifications:

    •     CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz
    •     RAM: 1024MB of DDR3
    •     Storage: 256MB Nand
    •     Ethernet: 4x 1G RJ45 ports (QCA8075) + 1 2.5G Port (QCA8081)
    •     WLAN:
          2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 1174 Mbps PHY rate
          5GHz: Qualcomm QCN5054 4x4 802.11a/b/g/n/ac/ax 2402 PHY rate
    •     1x USB 3.0

    •     1 gpio-controlled dual color led (blue/red)

            • Buttons: 1x soft reset / 1x WPS
            • Power: 12V DC jack

        A poulated serial header is onboard (J1004)
        the connector size is a 4-pin 2.0 mm JST PH.
        RX/TX is working, u-boot bootwait is active, secure boot is enabled.

        Notes:
	- Serial is completely deactivated in the stock firmware image.
	- This commit adds only single partition support, that means
	  sysupgrade is upgrading the current rootfs partition.
	- Installation can be done by serial connection or
	  SSH access on OEM firmware

	Installation Instructions:

	Most part of the installation is performed from an initramfs image
	running OpenWrt, and there are two options to boot it.

	Boot initramfs option 1: Using serial connection (3.3V)
	1. Stop auto boot to get to U-boot shell
	2. Transfer initramfs image to device
	   (openwrt-ipq807x-generic-dynalink_dl-wrx36-initramfs-uImage.itb)
	   Tested using TFTP and a FAT-formatted USB flash drive.
	3. Boot the initramfs image
	   # bootm

	Boot initramfs option 2: From SSH access on OEM firmware
	1. Copy the initramfs image to a FAT-formatted flash drive
	   (tested on single-partition drive) and connect it to device USB port.
	2. Change boot command so it loads the initramfs image on next boot
	   Fallback to OEM firmware is provided.
	   # fw_setenv bootcmd 'usb start && fatload usb 0:1 0x44000000 openwrt-ipq807x-generic-dynalink_dl-wrx36-initramfs-uImage.itb && bootm 0x44000000; bootipq'
	3. Reboot the device to boot the initramfs
	   # reboot

	Install OpenWrt from initramfs image:
	1. Use SCP (or other way) to transfer OpenWrt factory image
	2. Connect to device using SSH (on a LAN port)
	3. Check MTD partition table.
	   rootfs and rootfs_1 should be mtd18 and mtd20
	   depending on current OEM slot.
	   # cat /proc/mtd
	4. Do a ubiformat to both rootfs partitions:
	   # ubiformat /dev/mtd18 -y -f /path_to/factory_image
	   # ubiformat /dev/mtd20 -y -f /path_to/factory_image
	5. Set U-boot env variable: mtdids
	   # fw_setenv mtdids 'nand0=nand0'
	6. Get offset of mtd18 to determine current OEM slot
	   - If current OEM slot is 1, offset is 16777216  (0x1000000)
	   - If current OEM slot is 2, offset is 127926272 (0x7a00000)
	   # cat /sys/class/mtd/mtd18/offset
	7. Set U-boot env variable: mtdparts
	   If current OEM slot is 1, run:
	   # fw_setenv mtdparts 'mtdparts=nand0:0x6100000@0x1000000(fs),0x6100000@0x7a00000(fs_1)'
	   If current OEM slot is 2, run:
	   # fw_setenv mtdparts 'mtdparts=nand0:0x6100000@0x7a00000(fs),0x6100000@0x1000000(fs_1)'
	8. Set U-boot env variable: bootcmd
	   # fw_setenv bootcmd 'setenv bootargs console=ttyMSM0,115200n8 ubi.mtd=rootfs rootfstype=squashfs rootwait; ubi part fs; ubi read 0x44000000 kernel; bootm 0x44000000#config@rt5010w-d350-rev0'
	9. Reboot the device
	   # reboot

        Note: this PR adds only single partition support, that means sysupgrade is
              upgrading the current rootfs partition

Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
2023-01-16 12:42:23 +01:00
..
ath10k-ct-firmware ath10k-ct-firmware: set DL_DIR to package specific subdirectory 2022-09-22 16:48:36 -04:00
ath11k-firmware firmware: add ath11k-firmware package 2023-01-16 12:42:23 +01:00
cypress-firmware cypress-firmware: update to v5.10.9-2022_0909 2022-11-17 16:43:55 +01:00
cypress-nvram cypress-nvram: consolidate NVRAM packages 2022-11-16 20:14:13 +01:00
intel-microcode firmware: intel-microcode: update to 20220809 2022-09-24 23:53:53 +02:00
ipq-wifi ipq807x: add Dynalink DL-WRX36 2023-01-16 12:42:23 +01:00
lantiq/dsl-vrx200-firmware-xdsl treewide: unify OpenWrt hosted source via @OPENWRT 2021-02-05 12:00:24 -10:00
layerscape layerscape: update remaining PKG_HASH / PKG_MIRROR_HASH 2022-07-22 22:03:27 +02:00
linux-firmware linux-firmware: disable stripping 2022-12-29 14:15:55 +01:00
prism54-firmware prism54-firmware: set DL_DIR to package specific subdirectory 2022-09-22 16:48:37 -04:00
wireless-regdb wireless-regdb: update to 2022-08-12 2022-09-17 23:16:43 +02:00